maintenance schedule MAZDA MODEL PROTÉGÉ 2002 Owners Manual (in English)

4-6
Before Driving Your Mazda
Form No. 8Q36-EA-01F
Driving Tips
No special break-in is necessary, but a few
precautions in the first 1,000 km (600
miles) may add to the performance,
economy, and life of your Mazda.
•Don’t race the engine.
•Don’t maintain one constant speed for
long.
•Don’t drive constantly at full-throttle or
high engine rpm for extended periods
of time.
•Avoid unnecessary hard stops.
•Avoid full-throttle starts.How you operate your Mazda determines
how far it will travel on a tank of fuel. Use
these suggestions to help save money on
fuel and repairs.
•Avoid long warm-ups. Once the engine
runs smoothly, begin driving.
•Avoid fast starts.
•Keep the engine tuned. Follow the
maintenance schedule (page 8-3) and
have an Authorized Mazda Dealer
perform inspections and servicing.
•Use the air conditioner only when
necessary.
•Slow down on rough roads.
•Keep the tires properly inflated.
•Don’t carry unnecessary weight.
•Don’t rest your foot on the brake pedal
while driving.
•Keep the wheels in correct alignment.
•Keep windows closed at high speeds.
•Slow down when driving in crosswinds
and headwinds.
Break-In PeriodMoney-Saving Suggestions
Coasting:
Turning off the engine to coast down
a hill is dangerous. This causes the
loss of power steering and power
brake control. Any loss of steering or
braking control could cause an
accident. Never turn off the engine
and coast down a hill.
WARNING
J39L(02MY).book Page 6 Thursday, November 1, 2001 10:49 AM

8-1
Form No. 8Q36-EA-01F
8Maintenance and Care
How to keep your Mazda in top condition.
Introduction
................................................................................. 8- 2
Introduction ............................................................................. 8- 2
Scheduled Maintenance
.............................................................. 8- 3
Scheduled Maintenance (Except Chile) .................................. 8- 3
Scheduled Maintenance (Chile) .............................................. 8- 6
Owner Maintenance
.................................................................... 8- 8
Owner Maintenance Schedule ................................................. 8- 8
Owner Maintenance Precautions ............................................. 8- 9
Engine Compartment Overview .............................................. 8-10
Engine Oil ................................................................................ 8-11
Engine Coolant ........................................................................ 8-14
Brake/Clutch Fluid .................................................................. 8-16
Power Steering Fluid ............................................................... 8-18
Automatic Transaxle Fluid (ATF) ........................................... 8-18
Washer Fluid ............................................................................ 8-20
Body Lubrication ..................................................................... 8-21
Air Filter .................................................................................. 8-21
Wiper Blades ........................................................................... 8-22
Battery ..................................................................................... 8-25
Tires ......................................................................................... 8-26
Light Bulbs .............................................................................. 8-30
Fuses ........................................................................................ 8-39
Appearance Care
......................................................................... 8-43
How to Minimize Environmental Paint Damage ..................... 8-43
Exterior Care ........................................................................... 8-45
Interior Care ............................................................................ 8-48
J39L(02MY).book Page 1 Thursday, November 1, 2001 10:49 AM

8-3
Maintenance and Care
Form No. 8Q36-EA-01F
Scheduled Maintenance
Follow Schedule 1 if the vehicle is operated mainly where none of the following conditions
apply.
If any do apply, follow Schedule 2 (Canada and Puerto Rico residents follow Schedule 2).
•Repeated short-distance driving
•Driving in dusty conditions
•Driving with extended use of brakes
•Driving in areas where salt or other corrosive materials are being used
•Driving on rough or muddy roads
•Extended periods of idling or low-speed operation
•Driving for long periods in cold temperatures or extremely humid climates
Scheduled Maintenance (Except Chile)
NOTE
After the described period, continue to follow the described maintenance at the
recommended intervals.
J39L(02MY).book Page 3 Thursday, November 1, 2001 10:49 AM

8-4
Maintenance and Care
Scheduled Maintenance
Form No. 8Q36-EA-01F

Schedule 1
I
: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R
: Replace
L
: Lubricate
*1: According to state and federal regulations, failure to perform maintenance on these items will not void your
emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometrage (mileage) period to ensure long-term reliability.
Maintenance
Interval
Maintenance
ItemNumber of months or kilometers (miles), whichever comes first
Months 6 12182430364248
×1000 Km 12 24 36 48 60 72 84 96
(×1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60)
Engine valve clearanceI
Engine timing belt Inspect at 96,000 km (60,000 miles)
Replace every 168,000 km (105,000 miles)
Drive belts (tension) II
Engine oilRRRRRRRR
Engine oil filterRRRRRRRR
Cooling systemII
Engine coolantReplace at first 72,000 km (45,000 miles) or 36 months ;
after that, every 48,000 km (30,000 miles) or 24 months
Idle speedII
Air filterRR
Fuel lines & hoses*
1II
Hoses & tubes for emission*1I
Spark plugsRR
Brake lines, hoses & connectionsII
Disc brakesII
Drum brakesII
Steering operation & linkagesII
Front suspension ball jointsII
Driveshaft dust bootsII
Bolts & nuts on chassis & bodyII
Exhaust system heat shieldsII
All locks & hingesLLLLLLLL
Refrigerant amount (if installed) IIII
Compressor operation (if installed) IIII
J39L(02MY).book Page 4 Thursday, November 1, 2001 10:49 AM

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8Q36-EA-01F

Schedule 2
I
: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R
: Replace
L
: Lubricate
*1: According to state and federal regulations, failure to perform maintenance on these items will not void your
emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometrage (mileage) period to ensure long-term reliability.
*2: If the vehicle is operated in cold districts { below -18 degrees C (0 degrees F) }, replace the timing belt at
96,000 km (60,000 miles).
Maintenance
Interval
Maintenance
ItemNumber of months or kilometers (miles), whichever comes first
Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 Km 8 1624324048566472808896
(×1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60)
Engine valve clearanceI
Engine timing belt
*2Inspect at 96,000 km (60,000 miles)
Replace every 168,000 km (105,000 miles)
Drive belts (tension) II
Engine oilExcept Puerto RicoRRRRRRRRRRRR
Puerto RicoReplace every 5,000 km (3,000 miles) (or 3 months)
Engine oil filterRRRRRRRRRRRR
Cooling systemII
Engine coolantReplace at first 72,000 km (45,000 miles) or 36 months ;
after that, every 48,000 km (30,000 miles) or 24 months
Engine coolant levelIIIIIIIIIIII
Idle speedII
Air filter
I
*1R
I *1R
Fuel lines & hoses*1II
Hoses & tubes for emission*1I
Spark plugsRR
Function of all lightsIIIIIIIIIIII
Brake lines, hoses & connectionsII
Brake & clutch fluid level IIIIIIIIIIII
Disc brakesIIII
Drum brakesII
Tire inflation pressure and tire wearIIIIIIIIIIII
Steering operation & linkagesII
Power steering fluid levelIIIIIIIIIIII
Front suspension ball jointsII
Driveshaft dust bootsII
Bolts & nuts on chassis & bodyIIII
Exhaust system heat shieldsII
All locks & hingesLLLLLLLLLLLL
Washer fluid levelIIIIIIIIIIII
Refrigerant amount (if installed) IIII
Compressor operation (if installed) IIII
J39L(02MY).book Page 5 Thursday, November 1, 2001 10:49 AM

8-6
Maintenance and Care
Scheduled Maintenance
Form No. 8Q36-EA-01F
Emission control and related systems
The ignition and fuel systems are highly important to the emission control system and to
efficient engine operation. Don’t tamper with them.
All inspections and adjustments must be made by a qualified technician. We strongly
recommend that all servicing related to these systems be done by an Authorized Mazda
Dealer.
I
: Inspect: Inspect and clean, repair, adjust, or replace if necessary . R: Replace
*1: Also inspect and adjust the power steering and air conditioner drive belts, if installed.
*2: Replacement of the timing belt is required at every 100,000 km (60,000 miles). Failure to replace the timing
belt may result in damage to the engine.
*3: If the vehicle is operated under any of the following conditions, change the engine oil and oil filter more often
than recommended intervals.
a) Driving in dusty conditions.
b) Extended periods of idling or low speed operation.
c) Driving for long period in cold temperatures or driving regularly at short distance only.
*4: If the vehicle is operated in very dusty or sandy areas, inspect and if necessary, clean or replace the air filter
more often than the recommended intervals.
Scheduled Maintenance (Chile)
NOTE
•After the described period, continue to follow the described maintenance at the
recommended intervals.
•As the result of visual examination or functional measurement of a system’s
operation (performance), correct, clean, or replace as required. (Inspect, and if
necessary replace the air filter)
Maintenance
Interval
Maintenance
ItemNumber of months or km (miles), whichever comes first
Months 6 121824303642485460667278849096
×1000 Km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
(×1000 Miles) (6) (12) (18) (24) (30) (36) (42) (48) (54) (60) (66) (72) (78) (84) (90) (96)
Engine valve clearance
Ins
pect every 100,000 km (60,000 miles) or 60 months
Idle speedIIIIIIII
Fuel filterRRRR
Spark plugsRRRRR
Evaporative system (if installed)
IIIIIIII
Drive belts*
1IIIIIIIIIIIIIIII
Engine timing belt*2Replace every 100,000 km (60,000 miles)
Engine oil*3RRRRRRRRRRRRRRRR
Oil filter*3RRRRRRRRRRRRRRRR
Cooling systemIIIIIIII
Engine coolant
Re
place every 2 years
Air filter*4IRIRIRIR
Fuel line and hosesIIIIIIII
J39L(02MY).book Page 6 Thursday, November 1, 2001 10:49 AM

8-7
Maintenance and Care
Scheduled Maintenance
Form No. 8Q36-EA-01F
I
: Inspect: Inspect and clean, repair, adjust, or replace if necessary . R: Replace
L
: Lubricate T
: Tightenan
*5: If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle
is operated in extremely humid climates, change the brake fluid annually.
*6: This is a full function check of electrical systems such as lights, wiper and washer systems (including wiper
blades), and power windows.
Maintenance
Interval
Maintenance
ItemNumber of months or km (miles), whichever comes first
Months 6 121824303642485460667278849096
×1000 Km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
(×1000 Miles) (6) (12) (18) (24) (30) (36) (42) (48) (54) (60) (66) (72) (78) (84) (90) (96)
E.G.R. system (if installed)IIIIIIII
Battery electrolyte level
and specific gravityIIIIIIII
Brake and clutch pedalsIIIIIIIIIIIIIIII
Brake lines, hoses and
connectionsIIIIIIII
Brake fluid*
5I I IRI I IRI I IRI I IR
Clutch fluidIIIIIIIIIIIIIIII
Parking brakeIIIIIIIIIIIIIIII
Power brake unit and hosesIIIIIIII
Disc brakesIIIIIIIIIIIIIIII
Drum brakesIIIIIIII
Power steering fluid and linesIIIIIIIIIIIIIIII
Steering operation and gear
housingIIIIIIII
Steering linkage, tie rod ends and
armsIIIIIIII
Manual transaxle oilRR
Automatic transaxle fluid levelIIII III
Automatic transaxle fluid
RRR
Front and rear suspension and
ball jointsIIII
Driveshaft dust bootsIIII
Exhaust system heat shieldsIIII
Wheel nutsTTTTTTTT
Bolts and nuts on chassis and
bodyTTTTTTTT
All electrical system
*6 IIIIIIII
Headlight alignmentIIIII
Body condition (for rust,
corrosion and perforation)Ins
pect annually
Tires
(including spare tire, with
inflation pressure adjustment)IIIIIIII
Hinges and catchesLLLLLLLL
Road testIIIIIIIIIIIIIIII
J39L(02MY).book Page 7 Thursday, November 1, 2001 10:49 AM

8-8
Maintenance and Care
Form No. 8Q36-EA-01F
Owner Maintenance
The owner or a qualified service technician should make these vehicle inspections at the
indicated intervals to ensure safe and dependable operation.
Bring any problem to the attention of an Authorized Mazda Dealer or qualified service
technician as soon as possible.

When Refueling
•Brake and clutch fluid level (page 8-16)
•Engine coolant level (page 8-14)
•Engine oil level (page 8-11)
•Washer fluid level (page 8-20)

At Least Monthly
•Tire inflation pressures (page 8-27)

At Least Twice a Year (For Example, Every Spring and Fall)
•Automatic transaxle fluid level (page 8-18)
•Power steering fluid level (page 8-18)
You can do the following scheduled maintenance items if you have some mechanical
ability and a few basic tools and if you closely follow the directions in this manual.
•Air filter (page 8-21)
•Engine coolant (page 8-14)
•Engine oil (page 8-12)
Owner Maintenance Schedule
J39L(02MY).book Page 8 Thursday, November 1, 2001 10:49 AM

8-12
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F
5. Pull it out again and examine the level.
It’s OK between L and F.
But if it’s near at or below L, add
enough oil to bring the level to F.
6. Make sure the O-ring is positioned
properly before reinserting the
dipstick.
The distance between L and F on the
dipstick represents the following:

Changing Engine Oil and Filter
Change engine oil and filter according to
Scheduled Maintenance (page 8-3).
Please act responsibly—protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.
Changing engine oil
Don’t add engine oil over F. This may
cause engine damage.
L (US qt, Imp qt) 1.0 (1.05, 0.87)
Full 1.8 and 2.0-liter engines
Low OK
CAUTION
Handling Used Engine Oil:
Continuous contact with used engine
oil is dangerous. It could cause skin
cancer. Always wash with soap and
water immediately after changing oil
and filter.
Checking or Changing Engine Oil:
Hot engine oil is dangerous. If the
engine has been running, the engine
oil becomes very hot. You could be
seriously burned. Don’t check or
change the engine oil when the
engine is hot.
WARNING
WARNING
1.6-liter engine
Loosen Tighten
Front
Drain
plug
J39L(02MY).book Page 12 Thursday, November 1, 2001 10:49 AM

8-14
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F

Inspecting Coolant Level
Inspect the antifreeze protection and
coolant level in the coolant reservoir at
least once a year—at the beginning of the
winter season—and before traveling
where temperatures may drop below
freezing.
Inspect the condition and connections of
all cooling system and heater hoses.
Replace any that are swollen or
deteriorated.
The coolant should be at full in the
radiator and between the FULL and LOW
marks on the coolant reservoir when the
engine is cool.If it’s at or near LOW, add enough coolant
to the coolant reservoir to provide
freezing and corrosion protection and to
bring the level to FULL.
Do not overfill.
If new coolant is required frequently,
consult an Authorized Mazda Dealer.

Changing Coolant
Change coolant according to Scheduled
Maintenance (page 8-3).
Engine Coolant
Hot Engine:
A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become very
hot. You could be burned. Don’t
inspect the coolant system or add
coolant when the engine is hot.
WARNING
Radiator coolant will damage paint.
Rinse it off quickly.
•Use only soft (demineralized) water
in the coolant mixture. Water that
contains minerals will cut down on
the coolant’s effectiveness.
•Don’t add only water. Always add a
proper coolant mixture.
•The engine has aluminum parts and
must be protected by an ethylene-
glycol-based coolant to prevent
corrosion and freezing.
•DO NOT USE alcohol or methanol
antifreeze. DO NOT MIX alcohol
or methanol with the coolant. This
could damage the cooling system.
•Don’t use a solution that contains
more than 60 % antifreeze.
This would reduce effectiveness.
CAUTION
CAUTION
J39L(02MY).book Page 14 Thursday, November 1, 2001 10:49 AM