ignition MAZDA MODEL PROTÉGÉ 2003 (in English) Owner's Guide

5-35
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q94-EA-02G

Cruise Set Indicator Light
This light comes on when a cruising speed
is set.

Seat Belt Warning Beep
If the driver’s seat belt is not fastened
when the ignition switch is turned to the
ON position, a beep will sound for about
6 seconds.

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when
any door is opened.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when any door is opened.
Beeps
J39L_EA.book Page 35 Saturday, June 8, 2002 5:35 PM

5-36
Driving Your Mazda
Form No. 8Q94-EA-02G
Switches and Controls

Headlights
To turn on the lights, turn the knob on the
end of the control lever.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when any door is opened.

Headlight High-Low Beams
Push the lever forward for high beams.
Pull it back for low.

Flashing the Headlights
To flash the headlights, pull the lever fully
toward you. The headlight switch need
not be on, and the lever will return to the
normal position when released.
Lighting Control
Lever Position OFF
Headlights Off Off On
Taillights
Parking lights
License lights
Side-marker lightsOff On On
NOTE
To prevent discharging the battery,
don’t leave the lights on while the
engine is off.
High beams
Low beams
J39L_EA.book Page 36 Saturday, June 8, 2002 5:35 PM

5-38
Driving Your Mazda
Switches and Controls
Form No. 8Q94-EA-02G
In Canada, vehicles must be driven with
the headlights on during daytime
operation.
For that reason, the daytime running lights
automatically turn on when the ignition
switch is turned to the ON position.The ignition switch must be in the ON
position.
Daytime Running Lights
NOTE
The running lights go off when the
parking brake is applied.
Windshield Wipers and
Washer
Frozen Washer Fluid:
Using windshield washer fluid in
freezing temperatures is dangerous.
The washer fluid could freeze on the
windshield and block your vision.
You could have an accident. Don’t use
the washer without first warming the
windshield.
NOTE
Because heavy ice and snow can jam
the wiper blades, the wiper motor is
protected by a circuit breaker. This
mechanism will automatically stop
operation of the blades, but only for
about 5 minutes.
If this happens, turn off the wiper
switch and park off the right-of-way,
and remove the snow and ice.
After 5 minutes, turn on the switch and
the blades should operate normally. If
they don’t resume functioning, consult
an Authorized Mazda Dealer as soon
as possible.
WARNING
J39L_EA.book Page 38 Saturday, June 8, 2002 5:35 PM

5-40
Driving Your Mazda
Switches and Controls
Form No. 8Q94-EA-02G
The ignition switch must be in the ON
position.

Rear Window Wiper
Turn the wiper on by turning the knob.
ON
—
Normal
INT
—
Intermittent

Rear Window Washer
To spray washer fluid, turn the knob to the
position. After the knob is released,
the washer will stop.
If the washer doesn’t work, inspect the
fluid level (page 8-18). If it’s OK and the
washer still doesn’t work, consult an
Authorized Mazda Dealer.The rear defroster clears frost, fog, and
thin ice from the rear window.
The ignition switch must be in the ON
position.
Push the switch to turn on the rear
window defroster; the indicator light will
come on.
Push the switch again to turn it off.
Rear Window Wiper and
Washer (Hatchback)
NOTE
There are two washer positions: up and
down. In the down washer position, the
wiper will not be activated.
Washer WasherON
INT
OFF
Rear Window Defroster
Don’t use sharp instruments or
window cleaners with abrasives to
clean the inside of the rear window
surface. They may damage the
defroster grid inside the window.
NOTE
This defroster is not designed for
melting snow. If there is an
accumulation of snow on the rear
window, brush it off before using the
defroster.
CAUTION
J39L_EA.book Page 40 Saturday, June 8, 2002 5:35 PM

6-18
Interior Comfort
Au di o S ys t em
Form No. 8Q94-EA-02G

Power/Volume/Sound Controls
Power ON/OFF
Turn the ignition switch to the ACC or
ON position.
Press the power/volume knob to turn the
audio system on.
Press the power/volume knob again to
turn the audio system off.Volume adjustmentTo adjust the volume, turn the power/
volume knob.
Turn the power/volume knob to the right
to increase volume, to the left to decrease
it.
Display
Audio control knob Power/Volume knob
NOTE
To prevent the battery from being
discharged, do not leave the audio
system on for a long period when the
engine is not running.
J39L_EA.book Page 18 Saturday, June 8, 2002 5:35 PM

6-20
Interior Comfort
Au di o S ys t em
Form No. 8Q94-EA-02G

Clock
Setting the time
The clock can be set at any time when the
ignition switch is in the ACC or ON
position.
1. To adjust the time, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock’s current time will flash.
2. To advance the hours, press the hour
set button ( ). To advance the minutes,
press the minute set button ( ) while
the time is flashing.
3. Press the clock button ( ) again
to start the clock.Exact hour adjustment 1. To set the exact hour, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock’s current time will flash.
2. Press the clock button ( ) again
and the time will be adjusted as
follows:
(Example)
12:01—12:29
→12:00
12:30—12:59
→1:00
Display Clock button
Hour set
button
Minute set
button
NOTE
If the power supply to the unit is
interrupted (if the fuse blows or the
vehicle’s battery is disconnected), the
clock will need to be reset.
J39L_EA.book Page 20 Saturday, June 8, 2002 5:35 PM

6-25
Interior Comfort
Au di o S ys t em
Form No. 8Q94-EA-02G
Dolby and the double-D symbol are
trademarks of Dolby Laboratories
Licensing Corporation.
Ejecting the cassette tape
Press the cassette tape eject button ( ) to
eject the cassette tape.
Fast forward/Rewind
Press the fast-forward button ( ) to
fast-forward.
Press the rewind button ( ) to rewind.
To stop this operation and play the
cassette tape, press the button again.
Reversing
Press the program button ( ) to
change cassette tape-playing direction.
Automatic program control (APC)
APC is used to find the beginning of
either the next program or the one being
played.Press the APC button ( ) to the
beginning of the next selection.
Press the APC button ( ) to the
beginning of the one being played. To
stop this operation and play the cassette
tape, press the button again.
If APC detects 15 seconds of blank space
it will automatically advance the tape to
the next selection.
Repeat play
This operation makes it possible to listen
to a selection repeatedly.
Press the repeat button ( ) during play.
The current selection playing will be
repeated ("RPT" will be displayed).
Press the repeat button ( ) once again
to cancel repeat play.
NOTE
The cassette tape can be ejected when
the ignition switch is in the OFF
position.
NOTE
When the cassette tape ends during
fast forward or rewind, it automatically
stops and starts playing.
NOTE
When the cassette tape ends, the unit
automatically reverses play.
NOTE
APC may not operate properly if
•A tape was recorded at a low level.
•A tape has long, silent intervals.
•A tape is a live recording.
•A tape has very short intervals of
less than 3 seconds.
NOTE
RPT may not operate properly if
•A tape was recorded at a low level.
•A tape has long, silent intervals.
•A tape is a live recording.
•A tape has very short intervals of
less than 3 seconds.
J39L_EA.book Page 25 Saturday, June 8, 2002 5:35 PM

6-31
Interior Comfort
Au di o S ys t em
Form No. 8Q94-EA-02G
Multiple insertion
1. Press and hold the load button ( )
for about 2 seconds until a beep is
heard.
2. When "In" is displayed, insert the CD.
3. When "In" is displayed again, insert
the next CD.
Ejecting the CD
Normal ejection
1. Press the CD eject button ( ). The
disc number and "OUT" will be
displayed.
2. Pull out the CD.
Ejecting CDs from desired tray number
1. Press and hold the CD eject button ( )
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the
desired CD number within 5 seconds
after the beep is heard.
3. Pull out the CD.Multiple ejection
1. Press and hold the CD eject button ( )
for about 2 seconds until a beep is
heard.
2. Wait 5 seconds or press the CD eject
button ( ) again within 5 seconds
after the beep is heard.
3. Pull out the CD, then the next CD will
be ejected.
Playing
Press the CD play button ( ) to start
playing when a CD is in the unit.
Fast-forward/Reverse
Press and hold the fast-forward button
( ) to advance through a track at high
speed.
Press and hold the reverse button ( )
to reverse through a track at high speed.
Tr a c k s e a r c h
Press the track up button ( ) once to
skip forward to the beginning of the next
track.
Press the track down button ( ) once to
skip back to the beginning of the current
track.
NOTE
The first-inserted CD will be played
automatically when:
•No CD is inserted within 15
seconds after "In" is displayed.
•The CD trays are full.
NOTE
When the CD is ejected during play,
the next CD will be played
automatically.
NOTE
•CDs will be ejected starting with the
one with the lowest number.
•All CDs in the tray will be ejected
continuously.
•CDs can be ejected when the
ignition switch is off. Press and hold
the CD eject button ( ) for about 2
seconds and all CDs will eject.
J39L_EA.book Page 31 Saturday, June 8, 2002 5:35 PM

6-35
Interior Comfort
Form No. 8Q94-EA-02G
Interior Equipment
When you need a sunvisor, lower it for use
in front or swing it to the side.

Va n i t y M i r r o r s
To use the vanity mirror, lower the
sunvisor.

Illuminated Entry System
When the switch is in the DOOR position,
the overhead light comes on for:
•about 30 seconds after the driver’s door
is unlocked and the ignition key is
removed.
•about 15 seconds after all doors are
closed.
•about 15 seconds after the key is
removed from the ignition.
The light also goes out when:
•the ignition switch is turned to the ON
position and all doors are closed.
•the driver’s door is locked.
Sunvisors
Sunvisor
Interior Lights
NOTE
If any door is left opened, the light
goes out after about 5 minutes.
The light turns on again when the
ignition switch is turned to the ON
position, or when any door is opened
after all doors have been closed.
J39L_EA.book Page 35 Saturday, June 8, 2002 5:35 PM

6-37
Interior Comfort
Interior Equipment
Form No. 8Q94-EA-02G

Luggage Compartment Light
The ignition switch must be in the ACC or
ON position.
Press the lighter in and release it. When
ready for use, it automatically pops out.
OFF Light off
ON Light on when the liftgate is open
OFF
ON
Lighter
•Don’t touch the metal part of the
lighter, you may burn yourself.
•Don’t hold the lighter in because it
will overheat.
•Don’t use the lighter socket for
plug-in accessories such as shavers
and coffee pots. They may damage
it or cause electrical failure. Use
only a genuine Mazda lighter or the
equivalent.
•If the lighter doesn’t pop out within
30 seconds, remove it to prevent
overheating.
CAUTION
J39L_EA.book Page 37 Saturday, June 8, 2002 5:35 PM