warning MAZDA MODEL RX 8 2004 Owners Manual (in English)

7-5
In Case of an Emergency
Flat Tire
Form No. 8R65-EA-03C
The IMS emergency flat tire repair kit
included with your Mazda is for a
temporary repair of a slightly damaged
flat tire resulting from running over nails
or similar sharp objects on the road
surface. To avoid damage to the temporary
spare or to the vehicle, observe the
following precautions:
•Don’t exceed 80 km/h (50 mph).
•Avoid driving over obstacles.
Also, don’t drive through an
automatic car wash. This tire’s
diameter is smaller than a
conventional tire’s, so the ground
clearance is reduced about 25 mm
(1 in).
•Don’t use a tire chain on this tire
because it won’t fit properly.
•Don’t use your temporary spare on
any other vehicle; it has been
designed only for your Mazda.
•Use only one temporary spare tire
on your vehicle at the same time.
(With limited slip differential)

When using the temporary spare tire
on the rear axle, replace it with a
standard tire as soon as possible. The
size difference between the spare and
the standard tire will cause the limited
slip differential to malfunction.
NOTE
(With Tire Pressure Monitoring
System)

A tire pressure sensor is not installed
to the temporary spare tire. The
warning light will flash continuously
while the temporary spare tire is being
used (page 5-25).
CAUTIONInstant Mobility System
(IMS) Emergency Flat Tire
Repair Kit
NOTE
Your vehicle is not equipped with a
spare tire. In the event of a flat tire, use
the emergency flat tire repair kit to
repair the tire temporarily. When doing
the repair, refer to the instructions
included in the emergency flat tire
repair kit. After temporarily repairing a
tire with the emergency flat tire repair
kit, take your vehicle to an Authorized
Mazda Dealer to have the tire replaced.
J60E_8R65-EA-03C_Edition2.book Page 5 Saturday, April 26, 2003 1:48 PM

7-6
In Case of an Emergency
Flat Tire
Form No. 8R65-EA-03C

About the IMS Emergency Flat
Tire Repair Kit
The IMS emergency flat tire repair kit
includes the following items.
Tire sealant
Injection hoseCompressor
Spare valve
coreValve core
tool
CaseSpeed restriction
stickerRepaired tire
sticker
Instruction
Ingestion of Tire Sealant:
Ingestion of tire sealant is dangerous.
In the event tire sealant is
accidentally swallowed, drink large
amounts of water immediately and
seek medical assistance. Do not allow
children to touch the tire sealant.
Tire Sealant Contacting Eyes and
Skin:
Tire sealant that comes into contact
with the eyes and skin is dangerous. If
tire sealant enters the eyes or contacts
the skin, flush immediately with large
amounts of water and seek medical
assistance. Do not allow children to
touch the tire sealant.
WARNING
J60E_8R65-EA-03C_Edition2.book Page 6 Saturday, April 26, 2003 1:48 PM

7-7
In Case of an Emergency
Flat Tire
Form No. 8R65-EA-03C

Using the IMS Emergency Flat
Tire Repair Kit
1. Park on a level surface off the right-of-
way and set the parking brake.
2. Put a vehicle with an automatic
transmission in Park (P), a manual
transmission in Reverse (R) or 1, and
turn off the engine.
3. Turn on the hazard warning flasher.4. Unload passengers and luggage, and
remove the emergency flat tire repair
kit.
5. Shake the tire sealant well.
NOTE
•The tire sealant cannot be reused.
Purchase new tire sealant at an
Authorized Mazda Dealer.
•The emergency flat tire repair kit
cannot be used in the following
cases.
Consult an Authorized Mazda
Dealer.
The period of effective use for
the tire sealant has expired. (The
period of effectiveness is
indicated on the bottle label.)
The tear or puncture exceeds
about 4 mm (0.16 in).
The damage has occurred to an
area of the tire other than the
tread.
The vehicle has been driven with
nearly no air remaining in the
tire.
The tire has come off the wheel
rim.
Damage to the wheel rim has
occurred.
The tire has two or more
punctures.
If the bottle is shaken after the
injection hose is screwed on, tire
sealant could spray out from the
injection hose. Tire sealant contacting
clothing or other objects may be
impossible to remove. Shake the bottle
before screwing on the injection hose.
CAUTION
J60E_8R65-EA-03C_Edition2.book Page 7 Saturday, April 26, 2003 1:48 PM

7-9
In Case of an Emergency
Flat Tire
Form No. 8R65-EA-03C
10. Hold the bottom of the bottle upright,
squeeze the bottle with your hands,
and inject the entire amount of tire
sealant into the tire.
11. Pull out the injection hose from the
valve. Reinsert the valve core into the
valve and turn it clockwise to install
it.
12. Attach the sticker that indicates
completion of the tire repair on a flat
outer surface of the repaired tire.13. Attach the vehicle speed restriction
sticker in a place where the driver can
easily see it.
NOTE
The tire sealant cannot be reused.
Purchase new tire sealant at an
Authorized Mazda Dealer.
Valve
Repaired tire sticker
NOTE
Do not throw away the empty tire
sealant bottle as the sealant in the
bottle can be replenished when
replacing the tire. Take the bottle to an
Authorized Mazda Dealer.
Attaching Sticker to the Steering
Wheel Pad:
Attaching the vehicle speed restriction
sticker to the steering wheel pad is
dangerous. The sticker could interfere
with air bag inflation and cause
serious injury. Also, do not attach the
sticker to the meter panel, as it would
obstruct vision of areas such as
warning light indicators or the
speedometer.
Speed restriction sticker
WARNING
J60E_8R65-EA-03C_Edition2.book Page 9 Saturday, April 26, 2003 1:48 PM

7-10
In Case of an Emergency
Flat Tire
Form No. 8R65-EA-03C
14. Install the compressor hose to the tire
valve.
15. Insert the compressor plug into the
interior accessory socket and turn the
ignition switch to the ACC position
(page 6-48).16. Turn the compressor switch on and
inflate the tire carefully to the correct
inflation pressure.
•Before pulling out the compressor
plug from the electrical socket,
make sure the compressor power
switch is off.
•The compressor turns on and off
with the push-button switch.
Valve
Compressor hose
Compressor Compressor
plug
Center console
CAUTION
Operating the Compressor:
Operating the compressor above 300 kPa
(3.1 kgf/cm2, 3 bar, 43.5 psi) is
dangerous. When the inflation pressure
rises above 300 kPa (3.1 kgf/cm
2,
3 bar, 43.5 psi), heated air will be
exhausted from the back of the
compressor and you could be burned.
Never operate the compressor above
300 kPa (3.1 kgf/cm
2, 3 bar, 43.5 psi).
If the compressor operates slowly or
becomes hot, it indicates overheating.
Turn the compressor off immediately
and leave it turned off for 30 minutes
or longer.
WARNING
CAUTION
J60E_8R65-EA-03C_Edition2.book Page 10 Saturday, April 26, 2003 1:48 PM

7-11
In Case of an Emergency
Flat Tire
Form No. 8R65-EA-03C
17. When the tire has been inflated to the
proper inflation pressure, turn the
compressor switch off and remove the
compressor hose from the tire valve.
18. Install the tire valve cap.
19. Put the emergency flat tire repair kit
in the trunk and continue driving.20. After driving the vehicle for 10 minutes
or 5 km (3 miles), check the tire
pressure with the tire pressure gauge
equipped with the compressor. If the
tire pressure has fallen below the
correct tire pressure, inflate the tire to
the correct pressure again following the
steps from number 15.
NOTE
•Check the tire inflation pressure
label (driver’s door) for the correct
tire inflation pressure.
•Do not use the compressor for
longer than 10 minutes because
using the compressor for long
periods could damage it.
•If the tire does not inflate, repair of
the tire may not be possible. If the
tire does not reach the correct
inflation pressure within a 10-
minute period, it probably has
received more extensive damage.
When this happens, the emergency
flat tire repair kit cannot be used to
repair the tire. Contact an
Authorized Mazda Dealer.
•If the tire has been over-inflated,
loosen the screw cap on the
compressor and bleed some of the
air out.•Drive carefully to an Authorized
Mazda Dealer and keep the vehicle
speed below 80 km/h (50 mph).
•If the vehicle is driven 80 km/h
(50 mph) or higher, the vehicle
might begin to vibrate.
NOTE
(With Tire Pressure Monitoring
System)

If the tire is not properly inflated, the
tire pressure monitoring system
warning light will illuminate (page
5-25).
CAUTION
J60E_8R65-EA-03C_Edition2.book Page 11 Saturday, April 26, 2003 1:48 PM

7-13
In Case of an Emergency
Flat Tire
Form No. 8R65-EA-03C
1. Park on a level surface off the right-of-
way and firmly set the parking brake.
2. Put a vehicle with an automatic
transmission in Park (P), a manual
transmission in Reverse (R) or 1, and
turn off the engine.
3. Turn on the hazard warning flasher.
4. Have everyone get out of the vehicle
and away from the vehicle and traffic.
5. Remove the jack, and tool (page 7-3).
6. Block the wheel diagonally opposite
the tire to be changed. When blocking
a wheel, place a block both in front and
behind the tire.
Changing the Tire
Jacking a Vehicle:
Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure
someone.
Be sure to follow the directions for
changing a tire, and never get under a
vehicle that is supported only by a
jack.
Passenger in Vehicle Supported by a
Jack:
Allowing someone to remain in a
vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury. Never allow anyone inside a
vehicle supported by a jack.
(With Tire Pressure Monitoring
System)

The wheels equipped on your Mazda
are specially designed for installation
of the tire pressure sensors. Do not use
non-genuine wheels, otherwise it may
not be possible to install the tire
pressure sensors.
WARNING
CAUTION
NOTE
•Make sure the jack is well
lubricated before using it.
(With Tire Pressure Monitoring
System)

•Be sure to register the tire pressure
sensor ID signal code whenever tires
or wheels are changed (page 5-27).
J60E_8R65-EA-03C_Edition2.book Page 13 Saturday, April 26, 2003 1:48 PM

7-14
In Case of an Emergency
Flat Tire
Form No. 8R65-EA-03C

Removing the Tire
1. Loosen the lug nuts by turning them
counterclockwise one turn each, but
don’t remove any until the tire has been
raised off the ground.
2. Place the jack under the jacking
position closest to the tire being
changed.
3. Insert the jack handle into the jack.
NOTE
When blocking a tire, use a rock or
wood block of sufficient size to hold
the tire in place.
Jacking position
Incorrect Jacking Position:
Attempting to jack the vehicle in
positions other than those
recommended in this manual is
dangerous. The vehicle could slip off
the jack and seriously injure or even
kill someone. Use only the front and
rear jacking positions recommended
in this manual.
Improper Jack:
Using a jack that isn’t designed for
your Mazda is dangerous. The vehicle
could slip off the jack and seriously
injure someone. Use only the jack
provided with your Mazda.
Placing Objects Under the Jack:
Jacking the vehicle with an object
under the jack is dangerous. The jack
could slip and someone could be
seriously injured by the jack or the
falling vehicle. Never place objects
under the jack.
WARNING
J60E_8R65-EA-03C_Edition2.book Page 14 Saturday, April 26, 2003 1:48 PM

7-16
In Case of an Emergency
Flat Tire
Form No. 8R65-EA-03C
To replace the nut
1. Place the key on top of the nut.
2. Place the lug wrench on top of the key,
apply pressure, and turn it clockwise.

Mounting the Tire
1. Remove dirt and grime from the
mounting surfaces of the wheel and
hub, including the hub bolts, with a
cloth.
2. Mount the tire.3. Install the lug nuts with the beveled
edge inward; tighten them by hand.
Removing Dirt and Grime from
Wheels, Hubs and Hub Bolts:
When changing or replacing a tire,
not removing dirt and grime from the
mounting surfaces of the wheel, hub
and hub bolts is dangerous. The lug
nuts could loosen while driving and
cause the tire to come off, resulting in
an accident. Make sure the mounting
surfaces of the wheel, hub and lug
nuts are clean before changing or
replacing tires.
WARNING
Don’t Apply Oil or Grease to Lug
Nuts, Bolts:
Applying oil or grease to lug nuts and
bolts is dangerous. The lug nuts could
loosen while driving and cause the
tire to come off, resulting in an
accident. In addition, lug nuts and
bolts could be damaged if tightened
more than necessary. Do not apply oil
or grease to lug nuts and bolts and do
not tighten the lug nuts beyond the
recommended tightening torque.
WARNING
J60E_8R65-EA-03C_Edition2.book Page 16 Saturday, April 26, 2003 1:48 PM

7-17
In Case of an Emergency
Flat Tire
Form No. 8R65-EA-03C
4. Turn the jack handle counterclockwise
and lower the vehicle. Use the lug
wrench to tighten the nuts in the order
shown.
If you’re unsure of how tight the nuts
should be, have them inspected at an
Authorized Mazda Dealer.
Nut tightening torque:

N·m (kgf·m, ft·lbf) 88—118 (9—12, 65—87)
Loose Lug Nuts:
Improperly or loosely tightened lug
nuts are dangerous. The wheel could
wobble or come off. This could result
in loss of vehicle control and cause a
serious accident. Always securely and
correctly tighten the lug nuts.
Metric Studs and Lug Nuts:
Because the wheel studs and lug nuts
on your Mazda have metric threads,
using a non-metric nut is dangerous.
On a metric stud, it would not secure
the wheel and would damage the stud,
which could cause the wheel to slip
off and cause an accident. Be sure to
reinstall the same nuts you removed
or replace them with metric nuts of
the same configuration.
Incorrect Tire Air Pressure:
Driving on tires with incorrect air
pressure is dangerous. Tires with
incorrect pressure could affect
handling and result in an accident.
Don’t drive with any tires that have
incorrect air pressure.
NOTE
To prevent the jack and tool from
rattling, store them properly.
WARNING
J60E_8R65-EA-03C_Edition2.book Page 17 Saturday, April 26, 2003 1:48 PM