belt MAZDA MODEL RX 8 2004 (in English) Owner's Guide

5-35
Driving Your Mazda
Form No. 8R65-EA-03C
Warning/Indicator Lights and Beeps
Warning/Indicator Lights
Signal Warning/Indicator Lights Page
Brake System Warning Light 5-37
Charging System Warning Light 5-38
Engine Oil Level Warning Light 5-38
Engine Coolant Level Warning Light 5-39
Check Engine Light 5-39
ABS Warning Light 5-40
Air Bag/Front Seat Belt Pretensioner System Warning Light 5-40
Warning/Indicator lights will appear in any of the highlighted areas
J60E_8R65-EA-03C_Edition2.book Page 35 Saturday, April 26, 2003 1:48 PM

5-36
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C
Signal Warning/Indicator Lights Page
Low Fuel Warning Light 5-41
Seat Belt Warning Light 5-41
Door-Ajar Warning Light 5-41
Low Washer Fluid Level Warning Light 5-41
Automatic Transmission Warning Light 5-42
Tire Pressure Monitoring System Warning Light 5-42
Security Indicator Light 5-43
Headlight High-Beam Indicator Light 5-43
Shift Position Indicator Light 5-44
TCS/DSC Indicator Light 5-44
DSC OFF Indicator Light 5-44
Cruise Main Indicator Light 5-45
Cruise Set Indicator Light 5-45
Light-On Indicator Light 5-45
Power Steering Malfunction Indicator Light 5-45
Headlight Auto-Leveling Malfunction Indicator Light 5-46
Turn-Signal/Hazard Warning Indicator Lights 5-46
J60E_8R65-EA-03C_Edition2.book Page 36 Saturday, April 26, 2003 1:48 PM

5-40
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C

ABS Warning Light
The warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
If the ABS warning light stays on while
you’re driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible.
Air Bag/Front Seat Belt
Pretensioner System Warning
Light
If the air bag/front seat belt pretensioner
system is OK, the warning light comes on
when the ignition switch is turned to the
ON position or after the engine is cranked.
After about 6 seconds it goes out.
A system malfunction is indicated when
the warning light constantly flashes, stays
on or doesn’t come on at all when the
ignition switch is turned to the ON
position. If any of these occur, consult an
Authorized Mazda Dealer as soon as
possible. The system may not work in an
accident.
ABS Warning Light and Brake
Warning Light on at the Same Time:
Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
NOTE
When the engine is jump-started to
charge the battery, uneven rpm occurs
and the ABS warning light comes on.
This is due to a weak battery, not a
malfunction.
Recharge the battery.
J60E_8R65-EA-03C_Edition2.book Page 40 Saturday, April 26, 2003 1:48 PM

5-41
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C

Low Fuel Warning Light
This warning light in the fuel gauge
signals that the fuel tank will soon be
empty.
Refuel as soon as possible.

Seat Belt Warning Light
If the driver’s seat belt is not fastened
when the ignition switch is turned to the
ON position, the seat belt warning light
will remain on until the belt is fastened.
If the system does not operate correctly,
consult an Authorized Mazda Dealer.

Door-Ajar Warning Light
This warning light comes on when any
door isn’t securely closed.

Low Washer Fluid Level
Wa r n i n g L i g h t *
This warning light reveals that little
windshield washer fluid remains. Add
fluid (page 8-17).
Self-Servicing the Air Bag/
Pretensioner Systems:
Self-servicing or tampering with the
systems is dangerous. An air bag/
pretensioner could accidentally
activate or become disabled. This
could cause serious injuries. Never
tamper with the systems and always
have an Authorized Mazda Dealer
perform all servicing and repairs.
WARNING
Low fuel warning light
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 41 Saturday, April 26, 2003 1:48 PM

5-47
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C

Seat Belt Warning Beep
If the driver’s seat belt is not fastened
when the ignition switch is turned to the
ON position, a beep will sound for about
6 seconds.

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when the
driver’s door is opened.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when the driver’s door is opened.

Engine Overrev Warning Beep
The beep sounds to indicate engine
overrev when the tachometer needle
enters the striped zone (page 5-31).

Tire Inflation Pressure Warning
Beep*
The warning beep sounds for about 3
seconds when there is any abnormality in
tire inflation pressures.
(page 5-24)
Beeps
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 47 Saturday, April 26, 2003 1:48 PM

7-22
In Case of an Emergency
Emergency Starting
Form No. 8R65-EA-03C
7. Start the engine of the booster vehicle
and run it a few minutes. Then start the
engine of the other vehicle.
8. When finished, carefully disconnect
the cables in the reverse order
described in Step 6.You can’t start a vehicle with an automatic
transmission by pushing it.
Connecting to Negative Terminal:
Connecting the end of the second
cable to the negative ( ) terminal of
the discharged battery is dangerous.
A spark could cause the gas around
the battery to explode and injure
someone. Connect the cable to a point
away from the battery.
Connecting Jumper Cable to Moving
Par ts:
Connecting a jumper cable near or to
moving parts (cooling fans, belts) is
dangerous. The cable could get
caught when the engine starts and
cause serious injury. Never connect a
jumper cable to or near any part that
moves.
NOTE
Verify that the engine cover is securely
installed.
WARNINGPush-Starting
Towing a Vehicle to Start It:
Towing a vehicle to start it is
dangerous. The vehicle being towed
could surge forward when its engine
starts, causing the two vehicles to
collide. The occupants could be
injured. Never tow a vehicle to start it.
You shouldn’t push-start a vehicle that
has a manual transmission. It can
damage the emission control system.
WARNING
CAUTION
J60E_8R65-EA-03C_Edition2.book Page 22 Saturday, April 26, 2003 1:48 PM

8-4
Maintenance and Care
Scheduled Maintenance
Form No. 8R65-EA-03C

Schedule 1
I
: Inspect and repair, clean, adjust, or replace if necessary.
R
: Replace
L
: Lubricate
C
:Clean
ENGINE
AIR CLEANER
IGNITION SYSTEM
FUEL SYSTEM
COOLING SYSTEM
CHASSIS & BODY
AIR CONDITIONER SYSTEM
*1 According to state / provincial and federal regulations, failure to perform maintenance on these items will not
void your emissions warranties. However, Mazda recommends that all maintenance services be performed at
the recommended time or mileage / kilometer period to ensure long-term reliability.
*2 Check the tire repair fluid expiration date every year when performing the periodic maintenance. Replace the
tire repair fluid bottle with new one before the expiration date.
Maintenance Interval
(Number of months or kilometers
(miles), whichever comes first)Months 6 12182430364248
×1000 km 12 24 36 48 60 72 84 96
×1000 miles 7.5 15 22.5 30 37.5 45 52.5 60
Engine oilRRRRRRRR
Engine oil filterRRRRRRRR
Drive beltII
Air filterCCRC
Spark plugsR
Fuel filterReplace every 160,000km (100,000miles)
Fuel lines, hoses and connections
*1II
Cooling systemII
Engine coolantR e p l a c e a t f i r s t 9 6 , 0 0 0 k m ( 6 0 , 0 0 0 m i l e s ) o r 4 8 m o n t h s ;
after that, every 24 months
Brake line, hoses and connectionII
Disk brakesIIII
Steering operation and linkagesII
Front and rear suspension and ball jointsII
Manual transmission oilR
Rear differential oilR
Driveshaft dust bootsII
Bolts and nut on seatsII
Exhaust system heat shieldsII
All locks and hingesLLLLLLLL
Flat tire repair kit
*2Inspect every year
Cabin air filter (If installed)Replace every 40,000km (25,000miles) or 24 months
J60E_8R65-EA-03C_Edition2.book Page 4 Saturday, April 26, 2003 1:48 PM

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8R65-EA-03C

Schedule 2
I
: Inspect and repair, clean, adjust, or replace if necessary.
R
: Replace
L
:Lubricate
C
:Clean
ENGINE
AIR CLEANER
IGNITION SYSTEM
FUEL SYSTEM
COOLING SYSTEM
CHASSIS & BODY
AIR CONDITIONER SYSTEM
*1 According to state / provincial and federal regulations, failure to perform maintenance on these items will not
void your emissions warranties. However, Mazda recommends that all maintenance services be performed at
the recommended time or mileage / kilometer period to ensure long-term reliability.
*2 Check the tire repair fluid expiration date every year when performing the periodic maintenance. Replace the
tire repair fluid bottle with new one before the expiration date.
Maintenance Interval
(Number of months or kilometers
(miles), whichever comes first)Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 km 8 1624324048566472808896
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Engine oilPuerto RicoReplace every 5,000km (3,000miles) or 3 months
OthersRRRRRRRRRRRR
Engine oil filterRRRRRRRRRRRR
Drive beltII
Air filterCCRC
Spark plugsR
Fuel filterReplace every 160,000km (100,000miles)
Fuel lines, hoses and connections
*1II
Cooling systemII
Engine coolantReplace at first 96,000km (60,000miles) or 48 months ;
after that, every 24 months
Brake line, hoses and connectionII
Brake fluidRR
Disk brakesIIII
Steering operation and linkagesII
Front and rear suspension and ball jointsII
Manual transmission oilRR
Rear differential oilRR
Driveshaft dust bootsII
Bolts and nut on seatsII
Exhaust system heat shieldsII
All locks and hingesLLLLLLLLLLLL
Flat tire repair kit
*2Inspect every year
Cabin air filter (If installed)Replace every 40,000km (25,000miles) or 24 months
J60E_8R65-EA-03C_Edition2.book Page 5 Saturday, April 26, 2003 1:48 PM

8-23
Maintenance and Care
Owner Maintenance
Form No. 8R65-EA-03C
For reasons of proper performance, safety,
and better fuel economy, always maintain
recommended tire inflation pressures and
stay within the recommended load limits
and weight distribution.

Tire Inflation Pressure
Inspect all tire pressures monthly
(including the spare*) when the tires are
cold. Maintain recommended pressures
for the best ride, top handling, and
minimum tire wear.
Refer to the specification charts (page
10-7).Tires
Using Different Tire Types:
Driving your vehicle with different
types of tires is dangerous. It could
cause poor handling and poor
braking; leading to loss of control.
Use all radial, all bias-belted, or all
bias-type tires.
Using Wrong-Sized Tires:
Using any other tire size than what is
specified for your Mazda (page 10-7)
is dangerous. It could seriously affect
ride, handling, ground clearance, tire
clearance, and speedometer
calibration. This could cause you to
have an accident. Use only tires that
are the correct size specified for your
Mazda.
Incorrect Tire Inflation:
Overinflation or underinflation of
tires is dangerous. Adverse handling
or unexpected tire failure could result
in a serious accident. Always inflate
the tires to the correct pressure (page
10-7).
WARNING
WARNING
NOTE
•Warm tires normally exceed
recommended pressures. Don’t
release air from warm tires to adjust
the pressure.
•Underinflation can cause reduced
fuel economy and poor sealing of
the tire bead, which will deform the
wheel and cause separation of tire
from rim.
•Overinflation can produce a harsh
ride and a greater possibility of
damage from road hazards.
Keep your tire pressure at the
correct levels. If one frequently
needs inflating, have it inspected.
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 23 Saturday, April 26, 2003 1:48 PM

8-46
Maintenance and Care
Appearance Care
Form No. 8R65-EA-03C

Cleaning the Lap/Shoulder Belt
We b b i n g
Clean the webbing with a mild soap
solution recommended for upholstery or
carpets. Follow instructions. Don’t bleach
or dye the webbing; this may weaken it.
After cleaning the belts, thoroughly dry
the belt webbing and make sure there is
no remaining moisture before retracting
them.

Cleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy film, clean them with
glass cleaner. Follow the directions on the
container.
Damaged Seat Belt:
Using damaged seat belts is
dangerous. In a collision, damaged
belts cannot provide adequate
protection. Have an Authorized
Mazda Dealer replace damaged belts
immediately.
•Don’t scrape or scratch the inside of
the rear window. You may damage
the rear window defroster grid.
•When washing the inside rear
window, use a soft cloth dampened
in lukewarm water, gently wiping
the antenna lines.
Use of glass cleaning products
could damage the antenna.
WARNING
CAUTION
J60E_8R65-EA-03C_Edition2.book Page 46 Saturday, April 26, 2003 1:48 PM