high beam MAZDA MODEL RX 8 2004 Owners Manual (in English)

5-36
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C
Signal Warning/Indicator Lights Page
Low Fuel Warning Light 5-41
Seat Belt Warning Light 5-41
Door-Ajar Warning Light 5-41
Low Washer Fluid Level Warning Light 5-41
Automatic Transmission Warning Light 5-42
Tire Pressure Monitoring System Warning Light 5-42
Security Indicator Light 5-43
Headlight High-Beam Indicator Light 5-43
Shift Position Indicator Light 5-44
TCS/DSC Indicator Light 5-44
DSC OFF Indicator Light 5-44
Cruise Main Indicator Light 5-45
Cruise Set Indicator Light 5-45
Light-On Indicator Light 5-45
Power Steering Malfunction Indicator Light 5-45
Headlight Auto-Leveling Malfunction Indicator Light 5-46
Turn-Signal/Hazard Warning Indicator Lights 5-46
J60E_8R65-EA-03C_Edition2.book Page 36 Saturday, April 26, 2003 1:48 PM

5-43
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C
If the warning light illuminates again even
after the tire pressures are adjusted, there
may be a tire puncture.
Vehicles with Instant Mobility System
(IMS) emergency flat tire repair kit
If an emergency tire repair is needed,
repair the punctured tire with the
emergency flat tire repair kit (page 7-5).
Vehicles with optional temporary spare
tire
If you have bought the optional temporary
spare tire, replace the punctured tire with
the temporary spare tire . Refer to the
manufacturer’s instructions.
Warning light flashes
When the warning light flashes, there may
be a system malfunction. Consult an
Authorized Mazda Dealer.

Security Indicator Light
This indicator light starts flashing every
2 seconds when the ignition switch is
turned from the ON to the ACC position
and the immobilizer system is armed.
The light stops flashing when the ignition
switch is turned to the ON position with
the correct ignition key.
At this time, the immobilizer system is
disarmed and the light illuminates for
about 3 seconds and then goes out.
If the engine doesn’t start with the correct
ignition key, and the security indicator
light keeps illuminating or flashing, the
system may have a malfunction. Consult
an Authorized Mazda Dealer.

Headlight High-Beam Indicator
Light
This light indicates one of two things:
•The high-beam headlights are on.
•The turn signal lever is in the flash-to-
pass position. When replacing/repairing the tires or
wheels or both, have the work done by
an Authorized Mazda Dealer, or the
tire pressure sensors may be damaged.
Do not use non-genuine tire sealant. It
may damage the tire pressure sensor.
NOTE
A tire pressure sensor is not installed
to the temporary spare tire. The
warning light will flash continuously
while the temporary spare tire is being
used.
CAUTION
CAUTION
J60E_8R65-EA-03C_Edition2.book Page 43 Saturday, April 26, 2003 1:48 PM

5-48
Driving Your Mazda
Form No. 8R65-EA-03C
Switches and Controls

Headlights
To turn on the lights, turn the headlight
switch on the end of the control lever.
Xenon fusion headlight bulbs*
The low-beam bulbs of the headlights
have xenon fusion bulbs that produce a
bright white beam over a wide area.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when the driver’s door is opened.

Headlight High-Low Beam
Push the lever forward for high beam.
Pull it back for low.
Lighting Control
Switch Position OFF
Headlights Off Off On
Taillights
Parking lights
License lights
Side-marker lightsOff On On
NOTE
To prevent discharging the battery,
don’t leave the lights on while the
engine is off.
Xenon Fusion Bulb Replacement:
Replacing the xenon fusion bulbs by
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Do not replace the xenon
fusion bulbs by yourself. Consult an
Authorized Mazda Dealer when the
replacement is necessary.
NOTE
If the headlights flash, or the
brightness weakens, the bulb-life may
be depleted and a replacement is
necessary. Consult an Authorized
Mazda Dealer.
WARNING
Low beamHigh beam
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 48 Saturday, April 26, 2003 1:48 PM

5-50
Driving Your Mazda
Switches and Controls
Form No. 8R65-EA-03C

Turn Signal
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to flash
after a turn, manually return the lever to
its original position.
Green indicators on the dashboard show
which signal is working.
Lane-change signals
Move the lever slightly toward the
direction of the change —until the
indicator flashes— and hold it there. It
will return to the off position when
released.Use this switch to turn on the fog lights.
They help you to see as well as to be seen.
To turn the front fog lights on, rotate the
fog light switch to the position.
The headlight switch must be in the
position to turn on the front fog lights.
To turn them off, rotate the fog light
switch to the or OFF position or turn
the headlight switch to the OFF position.
Turn and Lane-Change
Signals
NOTE
If an indicator light stays on without
flashing or if it flashes abnormally, the
turn signal bulb may be burned out.
Right turn
Left turn Right lane
change
Left lane
changeOFF
Fog Lights*
NOTE
The fog lights will turn off when the
headlights are set at high beam.
Fog light switch
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 50 Saturday, April 26, 2003 1:48 PM

6-11
Interior Comfort
Au di o S ys t em
Form No. 8R65-EA-03C
Signals from an FM transmitter are
similar to beams of light because they do
not bend around corners, but they do
reflect. Unlike AM signals, FM signals
cannot travel beyond the horizon.
Therefore, FM stations cannot be received
at the great distances possible with AM
reception.
Atmospheric conditions can also affect
FM reception. High humidity will cause
poor reception. However, cloudy days
may provide better reception than clear
days.
Multipath noise
Since FM signals can be reflected by
obstructions, it is possible to receive both
the direct signal and the reflected signal at
the same time. This causes a slight delay
in reception and may be heard as a broken
sound or a distortion. This problem may
also be encountered when in close
proximity to the transmitter.Flutter/Skip noise
Signals from an FM transmitter move in
straight lines and become weak in valleys
between tall buildings, mountains, and
other obstacles. When a vehicle passes
through such an area, the reception
conditions may change suddenly,
resulting in annoying noise.
Weak signal noise
In suburban areas, broadcast signals
become weak because of distance from
the transmitter. Reception in such fringe
areas is characterized by sound breakup.
Ionosphere
100—200 km (60—120 miles) FM wave
FM waveAM wave
DirectReflected wave
J60E_8R65-EA-03C_Edition2.book Page 11 Saturday, April 26, 2003 1:48 PM

8-27
Maintenance and Care
Owner Maintenance
Form No. 8R65-EA-03C
Light Bulbs
Headlights (High-beam)Front side-marker lights
Front turn signal lights
Headlights (Low-beam)
Fog lights*
Parking lights Overhead light/Map lights (Front)
Vanity mirror lights
Courtesy lights
Overhead light (Rear)
Trunk light
High-mount brake light
License plate light
Brake lights/Taillights
Reverse lights
Rear side-marker lights
Rear turn signal lights
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 27 Saturday, April 26, 2003 1:48 PM

8-28
Maintenance and Care
Owner Maintenance
Form No. 8R65-EA-03C
Your Mazda’s headlights and fog lights
have replaceable halogen bulbs.
Replacing a Headlight Bulb
1. Make sure the ignition switch is turned
off and the headlight switch is off.
2. Lift the hood and find the high and low
beam bulbs in the rear of the headlight
unit.
The outboard bulb is the LOW beam,
and the inboard one is the HIGH
beam.(page 8-27)
3. If you are changing the right headlight
bulb, start the engine, turn the steering
wheel all the way to the right, and turn
off engine. If you are changing the left
headlight bulb, turn the steering wheel
to the left.
4. Turn the center section of the plastic
retainer counterclockwise and remove
the retainers and partially peel back the
mudguard.
Xenon Fusion Bulb Replacement:
Replacing the xenon fusion bulbs by
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Do not replace the xenon
fusion bulbs by yourself. Consult an
Authorized Mazda Dealer when the
replacement is necessary.
Handling Halogen Bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when lit.
Never touch the glass portion of the
bulb with your bare hands and always
wear eye protection when handling or
working around halogen bulbs.
Children and Halogen Bulbs:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
Always keep halogen bulbs out of the
reach of children.
WARNING
Removal
Installation
J60E_8R65-EA-03C_Edition2.book Page 28 Saturday, April 26, 2003 1:48 PM

8-29
Maintenance and Care
Owner Maintenance
Form No. 8R65-EA-03C
High-beam bulb
1. Turn the socket and bulb assembly
counterclockwise and remove it.
Carefully remove the headlight bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.
2. Disconnect the bulb from the electrical
connector by pressing the tab on the
connector with your finger and pulling
the bulb upward.
3. Install the new bulb in the reverse order
of removal.Low-beam bulb(Xenon fusion bulb)
You cannot replace the low beam bulbs by
yourself.
The bulbs must be replaced at an
Authorized Mazda Dealer.
(Halogen bulbs)
1. Detach the electrical connector from
the sealing cover by pulling it to the
rear.
2. Detach the sealing cover from the bulb.
3. Unhook the bulb retaining spring.
4. Swing the retaining spring out and
away to free the headlight bulb.
NOTE
Use the protective cover and carton of
the replacement bulb to dispose of the
old bulb promptly out of the reach of
children.
Ta b
Socket
Sealing
cover
J60E_8R65-EA-03C_Edition2.book Page 29 Saturday, April 26, 2003 1:48 PM

8-36
Maintenance and Care
Owner Maintenance
Form No. 8R65-EA-03C

Fuse Panel Description
Fuse block (Engine compartment)
(Next to air filter)
(Near battery)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 MAIN 120AFor protection
of all circuits
2 HEATER 40A Heater
3 AIR PUMP 60A Air pump
4BTN 30APower
windows,
Power door
locks,
Illuminated
entry system,
Sunroof
*
5DEFOG 50ARear window
defroster
6 FAN 40A Electric fan
7ABS/DSC 60A
ABS, DSC
*
8ACC 30ALighter, Power
control mirror,
Accessory
socket, Audio
system
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
9HEAD 15AHeadlight high
beams
*,
Headlight
cleaner
*
10HEAD LOW
R15AHeadlight low
beam (RH)
11HEAD LOW
L15AHeadlight low
beam (LH)
12 DRL 15A
DRL*(Headlight
high beams)
13 DSC 30A
DSC*
14SEAT
WA R M20A
Seat warmer*
15 H/CLEAN 20AHeadlight
cleaner*
16 R.FOG 10A—
17 FOG 15A
Fog lights*
18 A/C MAG 10A Air conditioner
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 36 Saturday, April 26, 2003 1:48 PM

10-6
Specifications
Form No. 8R65-EA-03C

We i g h t s

Air Conditioner

Light Bulbs
Exterior light
The rear side-marker light bulbs cannot be replaced because they are an LED-type bulb.
The rear combination component must be replaced.
Interior light
ItemWe i g h t
Manual transmission Automatic transmission
GVWR (Gross Vehicle Weight Rating) 1,728 kg (3,809 lb) 1,748 kg (3,854 lb)
GAWR (Gross Axle Weight Rating)Front 827 kg (1,823 lb) 841 kg (1,854 lb)
Rear 901 kg (1,986 lb) 907 kg (2,000 lb)
CW (Curb Weight)USA 1,374 kg (3,029 lb) 1,385 kg (3,053 lb)
Canada 1,384 kg (3,051 lb) 1,394 kg (3,073 lb)
Gas complies with SAE J639 Maximum operating charge
HFC134a (R-134a) 0.42 kg (14.8 oz)
Light bulb WattageCategory
ECE R SAE
HeadlightsHigh beam 65 H9—
Low beamHalogen 55 H7—
Xenon fusion 35 D2S—
Front turn signal lights 21 WY21W—
Parking lights 5 W5W—
Fog lights
*55 H11—
Front side-marker lights 3.8—#194
High-mount brake light 21 W21W #7440
Rear turn signal lights 21 WY21W—
Brake lights/Taillights 21/5 W21/5W #7443
Reverse lights 21 W21W #7440
License plate light 5 W5W—
Rear side-marker lights 0.57——
Light bulb WattageCategory
ECE R
Trunk light 5 W5W
Overhead light/Map lights (Front) 5 W5W
Overhead light (Rear) 10—
Courtesy lights 5 W5W
Vanity mirror lights 1.8—
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 6 Saturday, April 26, 2003 1:48 PM