maintenance schedule MAZDA MODEL RX 8 2004 Owners Manual (in English)

4-7
Before Driving Your Mazda
Form No. 8R65-EA-03C
Driving Tips
No special break-in is necessary, but a
few precautions in the first 1,000 km
(600 miles) may add to the performance,
economy, and life of your Mazda.
•Don’t race the engine.
•Don’t maintain one constant speed for
long.
•Don’t drive constantly at full-throttle or
high engine rpm (over 7,000 rpm) for
extended periods of time.
•Avoid unnecessary hard stops.
•Avoid full-throttle starts.How you operate your Mazda determines
how far it will travel on a tank of fuel. Use
these suggestions to help save money on
fuel and repairs.
•Avoid long warm-ups. Once the engine
runs smoothly, begin driving.
•Avoid fast starts.
•Keep the engine tuned. Follow the
maintenance schedule (page 8-3) and
have an Authorized Mazda Dealer
perform inspections and servicing.
•Use the air conditioner only when
necessary.
•Slow down on rough roads.
•Keep the tires properly inflated.
•Don’t carry unnecessary weight.
•Don’t rest your foot on the brake pedal
while driving.
•Keep the wheels in correct alignment.
•Keep windows closed at high speeds.
•Slow down when driving in crosswinds
and headwinds.
Break-In PeriodMoney-Saving Suggestions
Coasting:
Stopping the engine when going down
a hill is dangerous. This causes the
loss of power steering and power
brake control, and may cause damage
to the drivetrain. Any loss of steering
or braking control could cause an
accident. Never stop the engine when
going down a hill.
WARNING
J60E_8R65-EA-03C_Edition2.book Page 7 Saturday, April 26, 2003 1:48 PM

6-2
Interior Comfort
Form No. 8R65-EA-03C
Climate Control System

Operating the Climate Control
System
Operate the climate control system with
the engine running.

Clearing the Air Inlet
Clear all obstructions like leaves, snow
and ice from the hood and the air inlet in
the cowling grille to improve the system
efficiency.

Foggy Windows
The windows may fog up easily in humid
weather. Use the climate control system to
defog the windows.
To help defog the windows, operate the air
conditioner to dehumidify the air.

Outside/Recirculated Air
Position
Use the outside air position in normal
conditions. The recirculated air position
can be used temporarily when driving on
dusty roads or for quick cooling of the
interior.

Parking in Direct Sunlight
If the vehicle has been parked in direct
sunlight during hot weather, open the
windows to let warm air escape, then run
the climate control system.

Not Using for a Long Period
Run the air conditioner at least once a
month to keep internal parts lubricated.

Check the Refrigerant before the
Weather Gets Hot
Have the air conditioner checked before
the weather gets hot. Lack of refrigerant
may make the air conditioner less
efficient. Consult an Authorized Mazda
Dealer for refrigerant inspection.
The air conditioner is filled with
HFC134a (R134a), a refrigerant that will
not damage the ozone layer.
If the air conditioner is low on refrigerant
or has a malfunction, consult an
Authorized Mazda Dealer.

Replacement of the Cabin Air
Filter
If your vehicle is equipped with an air
filter for the air conditioner, it is necessary
to change the filter periodically as
indicated in scheduled maintenance (page
8-3). Consult an Authorized Mazda
Dealer for replacement of the cabin air
filter.
Operating Tips
J60E_8R65-EA-03C_Edition2.book Page 2 Saturday, April 26, 2003 1:48 PM

8-1
Form No. 8R65-EA-03C
8Maintenance and Care
How to keep your Mazda in top condition.
Introduction
................................................................................... 8-2
Introduction ............................................................................... 8-2
Scheduled Maintenance
................................................................ 8-3
Scheduled Maintenance ............................................................. 8-3
Owner Maintenance
...................................................................... 8-6
Owner Maintenance Schedule ................................................... 8-6
Owner Maintenance Precautions ............................................... 8-7
Engine Compartment Overview ................................................ 8-8
Engine Oil .................................................................................. 8-9
Engine Coolant ........................................................................ 8-12
Brake/Clutch Fluid .................................................................. 8-14
Automatic Transmission Fluid (ATF) ...................................... 8-15
Washer Fluid ............................................................................ 8-17
Body Lubrication ..................................................................... 8-18
Air Filter .................................................................................. 8-18
Wiper Blades ........................................................................... 8-19
Battery ..................................................................................... 8-21
Tires ......................................................................................... 8-23
Light Bulbs .............................................................................. 8-27
Fuses ........................................................................................ 8-33
Appearance Care
......................................................................... 8-39
How to Minimize Environmental Paint Damage ..................... 8-39
Exterior Care ........................................................................... 8-41
Interior Care ............................................................................ 8-44
J60E_8R65-EA-03C_Edition2.book Page 1 Saturday, April 26, 2003 1:48 PM

8-3
Maintenance and Care
Form No. 8R65-EA-03C
Scheduled Maintenance
Follow Schedule 1 if the vehicle is operated mainly where none of the following conditions
apply.
If any do apply, follow Schedule 2 (Canada and Puerto Rico residents follow Schedule 2).
•Repeated short-distance driving
•Driving in dusty conditions
•Driving with extended use of brakes
•Driving in areas where salt or other corrosive materials are being used
•Driving on rough or muddy roads
•Extended periods of idling or low-speed operation
•Driving for long periods in cold temperatures or extremely humid climates
Scheduled Maintenance
NOTE
After the prescribed period, continue to follow the described maintenance at the
recommended intervals.
J60E_8R65-EA-03C_Edition2.book Page 3 Saturday, April 26, 2003 1:48 PM

8-4
Maintenance and Care
Scheduled Maintenance
Form No. 8R65-EA-03C

Schedule 1
I
: Inspect and repair, clean, adjust, or replace if necessary.
R
: Replace
L
: Lubricate
C
:Clean
ENGINE
AIR CLEANER
IGNITION SYSTEM
FUEL SYSTEM
COOLING SYSTEM
CHASSIS & BODY
AIR CONDITIONER SYSTEM
*1 According to state / provincial and federal regulations, failure to perform maintenance on these items will not
void your emissions warranties. However, Mazda recommends that all maintenance services be performed at
the recommended time or mileage / kilometer period to ensure long-term reliability.
*2 Check the tire repair fluid expiration date every year when performing the periodic maintenance. Replace the
tire repair fluid bottle with new one before the expiration date.
Maintenance Interval
(Number of months or kilometers
(miles), whichever comes first)Months 6 12182430364248
×1000 km 12 24 36 48 60 72 84 96
×1000 miles 7.5 15 22.5 30 37.5 45 52.5 60
Engine oilRRRRRRRR
Engine oil filterRRRRRRRR
Drive beltII
Air filterCCRC
Spark plugsR
Fuel filterReplace every 160,000km (100,000miles)
Fuel lines, hoses and connections
*1II
Cooling systemII
Engine coolantR e p l a c e a t f i r s t 9 6 , 0 0 0 k m ( 6 0 , 0 0 0 m i l e s ) o r 4 8 m o n t h s ;
after that, every 24 months
Brake line, hoses and connectionII
Disk brakesIIII
Steering operation and linkagesII
Front and rear suspension and ball jointsII
Manual transmission oilR
Rear differential oilR
Driveshaft dust bootsII
Bolts and nut on seatsII
Exhaust system heat shieldsII
All locks and hingesLLLLLLLL
Flat tire repair kit
*2Inspect every year
Cabin air filter (If installed)Replace every 40,000km (25,000miles) or 24 months
J60E_8R65-EA-03C_Edition2.book Page 4 Saturday, April 26, 2003 1:48 PM

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8R65-EA-03C

Schedule 2
I
: Inspect and repair, clean, adjust, or replace if necessary.
R
: Replace
L
:Lubricate
C
:Clean
ENGINE
AIR CLEANER
IGNITION SYSTEM
FUEL SYSTEM
COOLING SYSTEM
CHASSIS & BODY
AIR CONDITIONER SYSTEM
*1 According to state / provincial and federal regulations, failure to perform maintenance on these items will not
void your emissions warranties. However, Mazda recommends that all maintenance services be performed at
the recommended time or mileage / kilometer period to ensure long-term reliability.
*2 Check the tire repair fluid expiration date every year when performing the periodic maintenance. Replace the
tire repair fluid bottle with new one before the expiration date.
Maintenance Interval
(Number of months or kilometers
(miles), whichever comes first)Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 km 8 1624324048566472808896
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Engine oilPuerto RicoReplace every 5,000km (3,000miles) or 3 months
OthersRRRRRRRRRRRR
Engine oil filterRRRRRRRRRRRR
Drive beltII
Air filterCCRC
Spark plugsR
Fuel filterReplace every 160,000km (100,000miles)
Fuel lines, hoses and connections
*1II
Cooling systemII
Engine coolantReplace at first 96,000km (60,000miles) or 48 months ;
after that, every 24 months
Brake line, hoses and connectionII
Brake fluidRR
Disk brakesIIII
Steering operation and linkagesII
Front and rear suspension and ball jointsII
Manual transmission oilRR
Rear differential oilRR
Driveshaft dust bootsII
Bolts and nut on seatsII
Exhaust system heat shieldsII
All locks and hingesLLLLLLLLLLLL
Flat tire repair kit
*2Inspect every year
Cabin air filter (If installed)Replace every 40,000km (25,000miles) or 24 months
J60E_8R65-EA-03C_Edition2.book Page 5 Saturday, April 26, 2003 1:48 PM

8-6
Maintenance and Care
Form No. 8R65-EA-03C
Owner Maintenance
The owner or a qualified service technician should make these vehicle inspections at the
indicated intervals to ensure safe and dependable operation.
Bring any problem to the attention of an Authorized Mazda Dealer or qualified service
technician as soon as possible.

When Refueling
•Brake and clutch fluid level (page 8-14)
•Engine coolant level (page 8-12)
•Engine oil level (page 8-10)
•Washer fluid level (page 8-17)

At Least Monthly
•Tire inflation pressures (page 8-23)

At Least Twice a Year (For Example, Every Spring and Fall)
•Automatic transmission fluid level (page 8-15)
You can do the following scheduled maintenance items if you have some mechanical
ability and a few basic tools and if you closely follow the directions in this manual.
•Air filter (page 8-18)
•Engine coolant (page 8-12)
•Engine oil (page 8-10)
Owner Maintenance Schedule
J60E_8R65-EA-03C_Edition2.book Page 6 Saturday, April 26, 2003 1:48 PM

8-10
Maintenance and Care
Owner Maintenance
Form No. 8R65-EA-03C


Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal
operating temperature.
3. Turn it off and wait 5 minutes for the
oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
5. Pull it out again and examine the level.
It’s OK between L and F.
But if it’s near or below L, add enough
oil to bring the level to F.
The distance between L and F on the
dipstick represents the following:


Changing Engine Oil and Filter
Change engine oil and filter according to
Scheduled Maintenance (page 8-3).
Please act responsibly—protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.
Changing engine oil
Don’t add engine oil over F. This may
cause engine damage.
L (US qt, Imp qt) 1.7 (1.8, 1.5)
Full
Low OK
CAUTION
Handling Used Engine Oil:
Continuous contact with used engine
oil is dangerous. It could cause skin
cancer. Always wash with soap and
water immediately after changing oil
and filter.
Checking or Changing Engine Oil:
Hot engine oil is dangerous. If the
engine has been running, the engine
oil becomes very hot. You could be
seriously burned. Don’t check or
change the engine oil when the
engine is hot.
WARNING
WARNING
08.fm Page 10 Friday, July 4, 2003 11:45 AM

8-13
Maintenance and Care
Owner Maintenance
Form No. 8R65-EA-03C

Changing Coolant
Change coolant according to Scheduled
Maintenance (page 8-3).
For mixture percentage:To change coolant
1. Remove the cooling system cap.
2. Only when the engine is cool, loosen
the radiator drain plug and drain the
coolant into a suitable container.
Properly dispose of the used coolant. •Use only soft (demineralized) water
in the coolant mixture. Water that
contains minerals will cut down on
the coolant’s effectiveness.
•Don’t add only water. Always add a
proper coolant mixture.
•The engine has aluminum parts and
must be protected by an ethylene-
glycol-based coolant to prevent
corrosion and freezing.
•DO NOT USE alcohol or methanol
antifreeze. DO NOT MIX alcohol
or methanol with the coolant. This
could damage the cooling system.
•Don’t use a solution that contains
more than 60 % antifreeze.
This would reduce effectiveness.
ProtectionVo l u m e
Antifreeze
solutionWa t e r
Above -16°
C (3°
F) 35% 65%
Above -26°
C (-15°
F) 45% 55%
Above -40°
C (-40°
F) 55% 45%
CAUTIONRemoving the Cooling System Cap:
Removing the cooling system cap or
drain plug while the engine is
running or hot is dangerous. This
might lead to cooling system and
engine damage and could result in
serious injury from escaping hot
coolant or steam. Turn off the engine
and wait until it’s cool. Even then, be
very careful when removing the cap
or drain plug. Wrap a thick cloth
around it and slowly turn it
counterclockwise to the first stop.
Step back while the pressure escapes.
When you’re sure all the pressure is
gone, press down on the cap — still
using a cloth — turn the cap, and
remove it.
WARNING
J60E_8R65-EA-03C_Edition2.book Page 13 Saturday, April 26, 2003 1:48 PM

8-19
Maintenance and Care
Owner Maintenance
Form No. 8R65-EA-03C
3. Unfasten the clamps.
4. Lift off the air filter cover and remove
the filter.
5. Wipe inside the air cleaner housing
with a damp cloth.
6. Clean or replace the filter.
7. Install in the reverse order of removal.
Replace the filter according to Scheduled
Maintenance (page 8-3).Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.

Replacing Windshield Wiper
Blades
When the wipers no longer clean well, the
blades are probably worn or cracked.
Replace them.
NOTE
After installing the air filter cover,
make sure the electrical connector is
securely connected.
Clamp
Air filter cover
Air filter
Wiper Blades
•Hot waxes applied by automatic car
washers have been known to affect
the cleanability of windows.
•To prevent damage to the wiper
blades, don’t use gasoline,
kerosene, paint thinner, or other
solvents on or near them.
To prevent damage to the wiper arms
and other components, don’t move the
wipers by hand.
CAUTION
CAUTION
J60E_8R65-EA-03C_Edition2.book Page 19 Saturday, April 26, 2003 1:48 PM