ECU MAZDA MODEL SPEED MX-5 MIATA 2004 User Guide

3-13
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L

Opening the Trunk Lid from the
Inside
Pull the illuminated "T" shaped handle.
The handle is made of material that will
glow for hours in the darkness of the trunk
following a brief exposure to ambient
light.
The "T" shaped handle is located on the
inside of the trunk end trim.Open Trunk Lid and Children:
Leaving the trunk lid open or leaving
children in the vehicle with the keys is
dangerous. Children could open the
trunk lid and climb inside resulting in
possible injury or death from heat
exposure. Close the trunk lid and do
not allow children to play inside the
vehicle.
Unattended Children and Pets:
Leaving children or animals
unattended in a parked vehicle is
dangerous. Babies left sleeping and
kids who lock themselves in cars or
trunks can die very quickly from heat
prostration. Don
’t leave your children
or pets alone in a car at any time.
Don ’t leave the car or the trunk
unlocked. Always keep the car from
being a tempting place to play by
locking doors and the trunk, and
keeping the keys where children won ’t
play with them.
WARNING
Always keep the handle firmly
attached to the holder and in the
recessed position. Not securing the
handle this way could allow it to snag
luggage in the trunk and open the trunk
lid.
Handle
CAUTION
J07S_8T02-EA-03L_Edition1.book Page 13 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-16
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L

Fuel-Filler Lid
The remote fuel-filler lid release is
mounted in the center console.
To open the console, unlock it and pull the
release catch.
To open the fuel-filler lid, pull up on the
remote fuel-filler lid release.

Fuel-Filler Cap
To remove the filler cap, turn it
counterclockwise.
To close the filler cap, turn it clockwise
until it clicks.
Remote
fuel-fillerlid release
Make sure the fuel-filler cap is
tightened securely. The check engine
light may illuminate on when the cap
isn ’t tightened securely. If the light
remains on (even after you have
tightened the cap securely, driven, and
restarted the engine several times), it
may indicate a different problem.
Contact an Authorized Mazda Dealer
as soon as possible.
Open
Close
CAUTION
J07S_8T02-EA-03L_Edition1.book Page 16 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-17
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L

Opening the Hood
1. With the vehicle parked, pull the
release handle to unlock the hood. 2. Pull the hood latch up and lift the hood.
3. Use the support rod to hold the hood
open.

Closing the Hood
1. Check under the hood area to make
certain all filler caps are in place and
all loose items (e.g. tools, oil
containers, etc.) have been removed.
2. Insert the support rod in its clip while holding up the hood. Verify that the
support rod is secured in the clip before
closing the hood.
3. Close the hood so that it locks securely.
Hood
Closed and Securely Locked Hood:
A hood that is not closed and securely
locked is dangerous as it could fly
open while the vehicle is moving and
block the driver ’s vision which could
result in a serious accident. Always
check that the hood is closed and
securely locked.
WARNING
Release handleClip
Support rod
J07S_8T02-EA-03L_Edition1.book Page 17 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-19
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
•Before lowering or raising the top, stop
in a safe place off the right-of-way and
park on a level surface.
• Make sure nothing is on the top or near
the back window when raising or
lowering the top.
Even small objects may interfere and
cause damage.
• When lowering the top, make sure
objects inside the vehicle aren
’t blown
away by the wind.
• Secure all loose objects inside before
driving with the top down.
• To help prevent burglary or vandalism
and to ensure that the passenger
compartment stays dry, close the top
securely and lock all doors when
leaving the vehicle.
• Don
’t drive through an automatic car
wash; it may damage the top.
• Don
’t raise or lower the top when the
temperature is below 5 °C (41 °F) ; this
will damage the top material.
• Don
’t lower the top when it ’s wet. If
the top dries while folded, it will
deteriorate and shrink.
• Lowering the top while it
’s wet can
also cause water to drip into the
passenger compartment.
• Don
’t raise or lower the top when the
wind is strong; the wind could damage
the top.
Lowering the Convertible Top
1. Park the vehicle on a level surface and
firmly set the parking brake.
2. Lower the side windows, then turn off the ignition.
3. Pull down the sunvisors.
4. Remove all objects in the top storage area.
Objects in the Storage Area:
Putting heavy or sharp objects in the
top storage area is dangerous.
During a sudden stop or collision,
they can become projectiles that
might hit and injure passengers.
Don ’t place heavy or sharp objects in
the top storage area.
Sunvisor Sunvisor
WARNING
J07S_8T02-EA-03L_Edition1.book Page 19 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-20
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
5. Push the unlock buttons and fully release the top latches.
6. Lift up on the front section of the top to release it from the windshield header. 7. Fold back the front and carefully lower
it to the storage area, then put the
latches in the locked position.

Covering the Convertible Top
1. Cover the convertible top with the top
covering, stored in the trunk.
2. Feed the straps on the bottom of the covering through the lower links and
snap them into position.
3. Secure the top covering with the straps.
4. Affix the top covering fasteners.
Unlock button Top latch
Windshield header
Top covering
Link Strap
J07S_8T02-EA-03L_Edition1.book Page 20 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-21
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
5. Insert the top covering’s rear edge into
the groove in the body molding.

Raising the Convertible Top
1. Park the vehicle on a level surface and
firmly set the parking brake.
2. Lower the side windows, then turn off the ignition.
3. Pull down the sunvisors.
4. Undo the fasteners and straps. 5. Remove the top covering and store it
properly in the trunk.
6. Unlock the top latches and open them fully.
7. Hold the top lift handle and pull the top up and forward until it ’s against the
windshield header.
8. After securely hooking the top latches onto the windshield header, push each
latch up with the palm of your hand
until the lock buttons click and the
latches are locked.
Never drive with the top partially
folded or uncovered. Otherwise the top
and/or the top covering could be
damaged.
Top covering
Body
Molding
CAUTION
Sunvisor Sunvisor
Windshield header
J07S_8T02-EA-03L_Edition1.book Page 21 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-22
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
9. If the rear window defroster coupler is disconnected, connect the coupler.

Taking Care of the Top
Refer to convertible top maintenance
(page 8-45) for information on taking care
of the top.Make sure the top is securely locked
by pushing up on it.
Driving with the top unlocked could
damage the top.
NOTE
Make sure the top is securely locked
by pushing up on it. If it still sounds
loose (rattles) after being locked by the
top latches, have it inspected at an
Authorized Mazda Dealer.
CAUTION
Rear window defroster coupler
J07S_8T02-EA-03L_Edition1.book Page 22 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-24
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
•When removing the hardtop, make sure
the operation is performed by 2
persons.
• Before removing or installing the
hardtop, be sure you are parked out of
traffic in a flat area near the location
your top is to be stored.
• When removing the hardtop, make sure
objects inside the vehicle aren
’t blown
away by the wind.
• Secure all loose objects inside before
driving with the hardtop removed.
• Don
’t drive through an automatic car
wash; it may damage the hardtop.
• Don
’t remove or install the hardtop
when the wind is strong; the wind
could damage the hardtop.
• Before removing the hardtop, lower the
antenna.
• Removing the hardtop while it
’s wet
can cause water to drip into the
passenger compartment.

Removing the Detachable
Hardtop
1. Park the vehicle on a level surface and
firmly set the parking brake.
2. Lower the side windows, then turn off the ignition.
3. Pull down the sunvisors.
4. Push the unlock buttons and fully release the top latches.Fastening Mechanisms:
It is dangerous to place your hands or
fingers near the fastening
mechanisms. Your hands or fingers
could be caught and injured by the
mechanism. Always keep your hands
and fingers away from the fastening
mechanisms when moving the top.
WARNING
Sunvisor Sunvisor
Unlock button
Top latch
J07S_8T02-EA-03L_Edition1.book Page 24 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-27
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
4. Unlock the top latches and the side latches on the hardtop.
5. Align the rear deck latches with the rear deck studs and set the hardtop
squarely onto the body. 6. Slide the hardtop forward while
pressing down on the rear deck latches
to lock the latches, and then verify that
they are secure by attempting to lift the
rear of the hardtop.
Top latch assembly
Slide latch assembly
Rear deck stud
Hardtop Rear deck latch
Rear deck latch
• Be careful not to strike the body
with any of the protruding hardtop
latches.
• The rear defogger grid and the
defogger cord could be damaged
when removing or installing the top.
Make sure the rear defogger grid
isn
’t folded and the defogger cord
isn ’t caught between the vehicle ’s
body and the top.
Rear deck latch
CAUTION
J07S_8T02-EA-03L_Edition1.book Page 27 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

3-28
Knowing Your Mazda
Doors and Locks
Form No. 8T02-EA-03L
7. Push each top latch up with the palm of your hand until the lock buttons click
and the latches are locked.
8. Push each side latch down with the palm of your hand until the lock
buttons click and the latches are
locked. 9. Reconnect the rear window defroster
coupler.

Detachable Hardtop Appearance
Care
Refer to detachable hardtop maintenance
(page 8-46) for information on detachable
hardtop appearance care.
After installation, verify that all latches
are secure. Operating the vehicle with
unlocked latches may cause hardtop
damage or loss.
Side latch
CAUTION
NOTE
If the top rattles even when all latches
are secure, drive slowly and contact an
Authorized Mazda Dealer for
inspection.
Rear window defroster coupler
J07S_8T02-EA-03L_Edition1.book Page 28 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI