air condition MAZDA MODEL SPEED MX-5 MIATA 2004 User Guide

6-8
Interior Comfort
Climate Control System
Form No. 8T02-EA-03L

Ventilation
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the position.
3. Set the temperature control dial to the desired position.
4. Set the fan control dial to the desired speed.

Windshield Defrosting and
Defogging
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the position.
3. Set the temperature control dial to the desired position.
4. Set the fan control dial to the desired speed.

Dehumidifying (With Air
Conditioner)*
Operate the air conditioner in cool or cold
weather to help defog the windshield and
side windows.
1. Set the mode selector dial to the
desired position.
2. Set the air intake selector to the position.
3. Set the temperature control dial to the desired position.
4. Set the fan control dial to the desired speed.
5. Turn on the air conditioner.
Foggy Windshield:
Using the position with the
temperature control set to the cold
position will cause the outside of the
windshield to fog up. Your vision will
be hampered, which could lead to a
serious accident. Set the temperature
control to the hot or warm position
when using the position.
WARNING
NOTE
• For maximum defrosting, set the
temperature control dial to the
extreme hot position and the fan
control dial to position 4.
• If warm air is desired at the floor,
set the mode selector dial to the
position.
*Some models.
J07S_8T02-EA-03L_Edition1.book Page 8 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

6-58
Interior Comfort
Au di o S ys t em
Form No. 8T02-EA-03L
This CD player is made and tested to meet exacting safety standards. It meets FCC
requirements and complies with safety performance standards of the U.S. Department of
Health and Human Services.
Safety Certification
•This CD player should not be adjusted or repaired by anyone except qualified service
personnel.
If servicing is required, contact an Authorized Mazda Dealer.
• Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous laser exposure. Never operate the CD player
with the top case of the unit removed.
• Changes or modifications not expressly approved by the party responsible for
compliance could void the user
’s authority to operate this equipment.
NOTE
For CD player section:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
CAUTION
J07S_8T02-EA-03L_Edition1.book Page 58 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

7-11
In Case of an Emergency
Form No. 8T02-EA-03L
Overheating
If the temperature gauge indicates
overheating, the vehicle loses power, or
you hear a loud knocking or pinging
noise, the engine is probably too hot.
If the temperature gauge indicates
overheating:1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic transmission in park (P), a manual
transmission in neutral.
Apply the parking brake.
3. Turn off the air conditioner.
4. Check whether coolant or steam is escaping from under the hood or from
the engine compartment.
If steam is coming from the engine
compartment:
Don ’t go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the hood and start the engine.
If neither coolant nor steam is
escaping:
Open the hood and idle the engine until
it cools.
5. Make sure the cooling fan is operating, then turn off the engine after the
temperature has decreased.
Overheating
Cooling Fan and Engine
Inspection:
Inspecting the engine with the
ignition switch in the ON position is
dangerous. The cooling fan could
turn on unexpectedly even when the
engine isn ’t running. You could be
seriously injured by the fan. Turn the
ignition switch off and remove the key
from the ignition switch when you
inspect the engine.
Cooling System Cap:
When the engine and radiator are
hot, scalding coolant and steam may
shoot out under pressure and cause
serious injury. Don ’t remove the
cooling system cap when the engine
and radiator are hot.
Steam from Overheated Engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you. Open the hood
ONLY after steam is no longer
escaping from the engine.
WARNING
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an Authorized Mazda
Dealer.
CAUTION
J07S_8T02-EA-03L_Edition1.book Page 11 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

8-1
Form No. 8T02-EA-03L
8Maintenance and Care
How to keep your Mazda in top condition.
Introduction ................................................................................... 8-2
Introduction ............................................................................... 8-2
Scheduled Maintenance ................................................................ 8-3
Scheduled Maintenance (North America) ................................. 8-3
Scheduled Maintenance (Except North America) ..................... 8-7
Owner Maintenance .................................................................... 8-10
Owner Maintenance Schedule ................................................. 8-10
Owner Maintenance Precautions ............................................. 8-11
Engine Compartment Overview .............................................. 8-12
Engine Oil ................................................................................ 8-13
Engine Coolant ........................................................................ 8-15
Brake Fluid .............................................................................. 8-18
Clutch Fluid ............................................................................. 8-19
Power Steering Fluid ............................................................... 8-20
Automatic Transmission Fluid (ATF) ...................................... 8-21
Washer Fluid ............................................................................ 8-22
Body Lubrication ..................................................................... 8-23
Air Filter .................................................................................. 8-24
Wiper Blades ........................................................................... 8-25
Battery ..................................................................................... 8-27
Tires ......................................................................................... 8-28
Light Bulbs .............................................................................. 8-32
Fuses ........................................................................................ 8-36
Appearance Care ......................................................................... 8-40
How to Minimize Environmental Paint Damage ..................... 8-40
Exterior Care ........................................................................... 8-42
Interior Care ............................................................................ 8-47
J07S_8T02-EA-03L_Edition1.book Page 1 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

8-8
Maintenance and Care
Scheduled Maintenance
Form No. 8T02-EA-03L
I:Inspect: Inspect and clean, repair, adjust, or replace if necessary.
R: Replace
C: Clean
ENGINE
COOLING SYSTEM
FUEL SYSTEM
IGNITION SYSTEM
*1 Also inspect and adjust the power steering and air conditioner drive belts, if installed.
*2 Replacement of the timing belt is required at every 100,000 km {62,500 miles}. Failure to replace the timing belt may result in damage to the engine.
*3 If the vehicle is operated under any of the following conditions, change the engine oil and oil filter more often than recommended intervals.
a) Driving in dusty conditions.
b) Extended periods of idling or low speed operation.
c) Driving for long period in cold temperatures or driving regularly at short distance only.
*4 If the vehicle is operated in very dusty or sandy areas, inspect and if necessary, clean or replace the air filter more often than the recommended intervals.
Maintenance
Interval
(Number of
months or
kilometers (miles),
whichever
comes first) Months 6 121824303642485460667278849096
× 1000 km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
× 1000 miles
6.25 12.5 18.752531.25 37.5 43.755056.25 62.5 68.757581.25 87.5 93.75100
Engine valve clearance Inspect every 100,000 km (62,500 miles) or 60 months
Drive belts
*1IIIIIIIIIIIIIIII
Engine timing belt
*2Replace every 100,000 km (62,500 miles)
Engine oil*3RRRRRRRRRRRRRRRR
Engine oil filter*3RRRRRRRRRRRRRRRR
Cooling system IIIIIIII
Engine coolant except
Australia,
New Zealand
Replace every 24 months
Australia,
New Zealand Replace at first 80,000 km (50,000 miles) or 48 months ;
after that, every 24 months
Idle speed IIIIIIII
Air filter
*4
except
Australia,
New Zealand CCRCCRCC
Australia,
New Zealand CRCRC
Fuel filter except
Australia,
New Zealand
RRRR
Australia,
New Zealand RRR
Fuel lines and hoses IIIIIIII
Spark plugs Replace every 40,000km (25,000miles)
J07S_8T02-EA-03L_Edition1.book Page 8 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

8-9
Maintenance and Care
Scheduled Maintenance
Form No. 8T02-EA-03L
I:Inspect: Inspect and clean, repair, adjust, or replace if necessary.
R: Replace
T: Tighten
EMISSION CONTROL SYSTEM
ELECTRICAL SYSTEM
CHASSIS and BODY
*5 This is a full function check of electrical systems such as lights, wiper and washer systems (including wiper blades), and power windows.
*6 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle is operated in extremely humid climates, change the brake fluid annually.
Maintenance
Interval
(Number of
months or
kilometers (miles),
whichever
comes first) Months 6 121824303642485460667278849096
× 1000 km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
× 1000 miles
6.25 12.5 18.752531.25 37.5 43.755056.25 62.5 68.757581.25 87.5 93.75100
Evaporative system IIIIIIII
All electrical system
*5IIIIIIII
Brake pedals and clutch pedals IIIIIIIIIIIIIIII
Brake lines, hoses and
connections IIIIIIII
Clutch fluid IIIIIIIIIIIIIIII
Brake fluid
*6IIIRIIIRIIIRIIIR
Parking brake IIIIIIIIIIIIIIII
Power brake unit and hoses IIIIIIII
Disc brakes IIIIIIIIIIIIIIII
Power steering fluid and lines IIIIIIIIIIIIIIII
Steering operation and gear
housing IIIIIIII
Steering linkages, tie rod ends
and arms IIIIIIII
Manual transmission oil R
Rear differential oil RR
Front and rear suspension and
ball joints IIII
Automatic transmission fluid
level IIIIIIII
Drive shaft dust boots IIII
Bolts and nuts on chassis and
body TTTTTTTT
Body condition (for rust,
corrosion and perforation)
(except Australian model) Inspect annually
Exhaust system heat shields Inspect every 80,000 km (50,000 miles)
Tire (including spare tire)(with
inflation pressure adjustment) IIIIIIII
J07S_8T02-EA-03L_Edition1.book Page 9 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

8-24
Maintenance and Care
Owner Maintenance
Form No. 8T02-EA-03L
This air filter may be cleaned with
compressed air and reused, or replaced,
depending on its condition. Unless it is
very dirty, simply shake it to remove
foreign particles. Each time you inspect it,
wipe inside the air cleaner housing with a
damp cloth.

Replacing the Air Filter
1. Loosen the bolt and remove the hose. 2. Unfasten the clamps.
3. Lift off the air filter cover and remove
the filter.
4. Wipe inside the air cleaner housing with a damp cloth.
5. Clean or replace the filter.
6. Install in the reverse order of removal.
Replace the filter according to Scheduled
Maintenance (page 8-3).
Air Filter
Don ’t drive without an air filter. This
could result in excessive engine wear.
NOTE
If the vehicle is operated in very dusty
or sandy areas, replace the filter more
often than recommended intervals.
CAUTION
Bolt
MAZDASPEED MX-5
Clamp
Air filter cover
Air filter
J07S_8T02-EA-03L_Edition1.book Page 24 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

8-29
Maintenance and Care
Owner Maintenance
Form No. 8T02-EA-03L

Tire Rotation
To equalize tread wear, rotate the tires
every 12,000 km (7,500 miles)/8,000 km*
(5,000 miles) or sooner if irregular wear
develops. During rotation, inspect them
for correct balance.
*Unique driving conditions for USA,
Canada and Puerto Rico Also, inspect them for uneven wear and
damage. Abnormal wear is usually caused
by one or a combination of the following:
•
Incorrect tire pressure
• Improper wheel alignment
• Out-of-balance wheel
• Severe braking
After rotation, inflate all tire pressures to
specification (page 10-6) and inspect the
lug nuts for tightness.
NOTE
• Warm tires normally exceed
recommended pressures. Don
’t
release air from warm tires to adjust
the pressure.
• Underinflation can cause reduced
fuel economy and poor sealing of
the tire bead, which will deform the
wheel and cause separation of tire
from rim.
• Overinflation can produce a harsh
ride and a greater possibility of
damage from road hazards.
Keep your tire pressure at the
correct levels. If one frequently
needs inflating, have it inspected.
Front
Do not include (TEMPORARY USE ONLY)
spare tire in rotation.
Rotate unidirectional tires and radial
tires that have an asymmetrical tread
pattern or studs only from front to rear,
not from side to side. Tire performance
will be weakened if rotated from side
to side.
Limited-Slip Differential system;
don ’t use the following:
• Tires not of the designated size
• Tires of different sizes or types at
the same time
• Tires not sufficiently inflated
If these instructions aren ’t followed,
the rotation of the left and right wheels
will be different and will thus apply a
constant load on the limited-slip
differential.
This will cause a malfunction.
CAUTION
CAUTION
J07S_8T02-EA-03L_Edition1.book Page 29 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

8-30
Maintenance and Care
Owner Maintenance
Form No. 8T02-EA-03L

Replacing a Tire
If a tire wears evenly, a wear indicator will
appear as a solid band across the tread.
Replace the tire when this happens.
You should replace it before the band is
across the entire tread.

Temporary Spare Tire
Inspect the temporary spare tire at least
monthly to make sure it
’s properly
inflated and stored.
The temporary spare tire is easier to
handle because of its construction. It is
lighter and smaller than a conventional
tire and should be used only for an
emergency and only for a short distance.
Use the temporary only until the
conventional tire is repaired, which should
be as soon as possible.
Maintain its pressure at 420 kPa (4.2 kgf/
cm
2or bar, 60 psi).
Worn Tires:
Driving with worn tires is dangerous.
Reduced braking, steering, and
traction could result in an accident.
Always use tires that are in good
condition.
WARNING
New tread Worn tread
Tread wear indicator
•
Don
’t use your temporary spare tire
rim with a snow tire or a
conventional tire. Neither will
properly fit and could damage both
tire and rim.
• The temporary spare tire has a tread
life of up to 5,000 km (3,000 miles),
depending on road conditions and
driving habits.
• The temporary spare tire is for
limited use, however, if the tread
wear solid-band indicator appears,
replace the tire with the same type
of temporary spare (page 8-30).
CAUTION
J07S_8T02-EA-03L_Edition1.book Page 30 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

8-38
Maintenance and Care
Owner Maintenance
Form No. 8T02-EA-03L

Fuse Panel Description
Fuse block (Engine compartment)
*1 MX-5/miata*2 MAZDASPEED MX-5
DESCRIPTION FUSE RATING
PROTECTED COMPONENT
1 HEAD 40A Headlights, Rear defroster, Auto antenna
2 FUEL INJ 30A Fuel injection
3 MAIN 100A For protection of all circuits
4 IG KEY 60A All ignition related circuits
5 BLOWER 30A Blower motor
6F AN 30A
*1Cooling fan, Additional fan (air conditioner)
40A*2
7 BTN 1 30A Taillights, Dashboard illumination
8BTN 2 20A Audio amp*, Turn signal lights
9 ABS 20A
Antilock brake system*
10 STOP 15A Brake lights, Horn, Shift lock
*Some models.
J07S_8T02-EA-03L_Edition1.book Page 38 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI