overheating MAZDA MODEL SPEED MX-5 MIATA 2005 Owners Manual
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2005, Model line: MODEL SPEED MX-5 MIATA, Model: MAZDA MODEL SPEED MX-5 MIATA 2005Pages: 298, PDF Size: 3.03 MB
Page 87 of 298
Black plate (87,1)
Hazardous Driving
WARNING
Downshifting on Slippery Surfaces:
Downshifting into lower gear while
driving on slippery surfaces is
dangerous. The sudden change in tire
speed could cause the tires to skid.
This could lead to loss of vehicle
control and an accident. If it is
necessary to downshift on slippery
surfaces, be very careful.
When driving on ice or in water, snow,
mud, sand, or similar hazard:
lBe cautious and allow extra distance
for braking.
lAvoid sudden braking and quick
steering.
lIf your vehicle is not equipped with
ABS, brake with the pedal by using a
light up-down motion. Don't hold the
pedal down constantly.
If your vehicle is equipped with ABS,
don't pump the brakes. Continue to
press down on the brake pedal.
lIf you get stuck, select a lower gear and
accelerate slowly. Don't spin the rear
wheels.
lFor more traction in starting on
slippery surfaces such as ice or packed
snow, use sand, rock salt, chains,
carpeting, or other nonslip material
under the rear wheels.
NOTE
Use snow chains only on the rear
wheels.
Rocking the Vehicle
WARNING
Spinning the Wheels:
When the vehicle is stuck, spinning
the wheels at high speed is dangerous.
The spinning tire could overheat and
explode. This could cause serious
injuries. Don't spin the wheels at more
than 56 km/h (35 mph), and don't
allow anyone to stand behind a wheel
when pushing the vehicle.
CAUTION
Too much rocking may cause engine
overheating, transmission failure, and
tire damage.
If you must rock the vehicle to free it from
snow, sand or mud, depress the
accelerator slightly and slowly move the
shift lever from 1 (D) to R.
Before Driving Your Mazda
Driving Tips
4-9
MX-5 Miata_8T72-EA-04G_Edition2 Page87
Tuesday, August 31 2004 11:24 AM
Form No.8T72-EA-04G
Page 105 of 298
Black plate (105,1)
O/D OFF indicator light
This light comes on when the overdrive
has been turned off.
CAUTION
If the overdrive-off indicator light
flashes, the transmission has an
electrical problem. Continuing to drive
your Mazda in this condition could
cause damage to your transmission.
Consult an Authorized Mazda Dealer as
soon as possible.
qDriving Tips
Passing
For extra power when passing another
vehicle or climbing steep grades, depress
the accelerator fully. The transmission will
shift to a lower gear, depending on vehicle
speed.
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:
1. Depress the brake pedal.
2. Shift to D or 1, depending on the load
weight and grade steepness.
3. Release all brakes while gradually accelerating.
Descending steep grades
When descending a steep grade, shift to 2
or 1, depending on load weight and grade
steepness. Descend slowly, using the
brakes only occasionally to prevent them
from overheating.
Driving Your Mazda
Starting and Driving
5-13
MX-5 Miata_8T72-EA-04G_Edition2 Page105
Tuesday, August 31 2004 11:24 AM
Form No.8T72-EA-04G
Page 112 of 298
Black plate (112,1)
qTachometer
The tachometer shows engine speed in
thousands of revolutions per minute
(rpm).
Red zone
CAUTION
Don't run the engine with the
tachometer needle in the RED ZONE.
This may cause severe engine damage.
qEngine Coolant Temperature
Gauge
The engine coolant temperature gauge
shows the temperature of the engine
coolant.
If the needle exceeds normal range toward
H, it indicates overheating.
CAUTION
Driving with an overheated engine can
cause serious engine damage (page
7-11).
qFuel Gauge
The fuel gauge shows approximately how
much fuel is in the tank. We recommend
keeping the tank over 1/4 full. When the
low fuel warning light illuminates or
when the needle is near E, refuel as soon
as possible.
5-20
Driving Your Mazda
Instrument Cluster and Indicators
MX-5 Miata_8T72-EA-04G_Edition2 Page112
Tuesday, August 31 2004 11:24 AM
Form No.8T72-EA-04G
Page 123 of 298
Black plate (123,1)
Daytime Running Lights
(Canada)
In Canada, vehicles must be driven with
the headlights on during daytime
operation.
For that reason, the daytime running lights
automatically turn on when the ignition
switch is turned to the ON position.
NOTE
The running lights go off when the
parking brake is applied.
Windshield Wipers and
Washer
The ignition switch must be in the ON
position.
WARNING
Frozen Washer Fluid:
Using windshield washer fluid without
anti-freeze protection in freezing
temperatures is dangerous. The
washer fluid could freeze on the
windshield and block your vision. You
could have an accident. Don't use the
washer without first warming the
windshield and never use plain tap
water.
NOTE
Because heavy ice and snow can jam
the wiper blades, the wiper motor is
protected from motor breakdown,
overheating and possible fire by a
circuit breaker. This mechanism will
automatically stop operation of the
blades, but only for about 5 minutes.
If this happens, turn off the wiper
switch and park off the right-of-way,
and remove the snow and ice.
After 5 minutes, turn on the switch and
the blades should operate normally. If
they don't resume functioning, consult
an Authorized Mazda Dealer as soon as
possible.
Driving Your Mazda
Switches and Controls
5-31
MX-5 Miata_8T72-EA-04G_Edition2 Page123
Tuesday, August 31 2004 11:24 AM
Form No.8T72-EA-04G
Page 133 of 298
Black plate (133,1)
Rear window defroster switch
When using the rear window defroster
switch, refer to Rear Window Defroster
(page 5-33).
qHeating
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the hot position.
4. Set the fan control dial to the desired speed.
5. If dehumidified heating is desired, turn on the air conditioner.
NOTE
lIf the windshield fogs up easily, set
the mode selector dial to the
position.
lIf cooler air is desired at face level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
lThe air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
qCooling (With Air Conditioner)í
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the cold position. 3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner.
5. Adjust the fan control dial and temperature control dial to maintain
maximum comfort.
CAUTION
When using the air conditioner while
driving up long hills or in heavy traffic,
closely monitor the temperature gauge
(page 5-20).
The air conditioner may cause engine
overheating. If the gauge indicates
overheating, turn the air conditioner off.
NOTE
lWhen maximum cooling is desired,
set the temperature control dial to the
extreme cold position and set the air
intake selector to the
position,
then set the fan control dial to
position 4.
lIf warmer air is desired at floor level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
lThe air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
Interior Comfort
Climate Control System
6-7íSome models.
MX-5 Miata_8T72-EA-04G_Edition2 Page133
Tuesday, August 31 2004 11:24 AM
Form No.8T72-EA-04G
Page 194 of 298
Black plate (194,1)
Lighter
The ignition switch must be in the ACC
or ON position.
Press the lighter in and release it. When
ready for use, it automatically pops out.
CAUTION
lDon't touch the metal part of the
lighter, you may burn yourself.
lDon't hold the lighter in because it
will overheat.
lDon't use the lighter socket for plug-
in accessories such as shavers and
coffee pots. They may damage it or
cause electrical failure. Use only a
genuine Mazda lighter or the
equivalent.
lIf the lighter doesn't pop out within
30 seconds, remove it to prevent
overheating.
Ashtray
CAUTION
Don't use the ashtray for trash. You
might start a fire.
To remove, open and pull up the ashtray.
6-68
Interior Comfort
Interior Equipment
MX-5 Miata_8T72-EA-04G_Edition2 Page194
Tuesday, August 31 2004 11:24 AM
Form No.8T72-EA-04G
Page 199 of 298
Black plate (199,1)
7In Case of an Emergency
Helpful information on what to do in an emergency.
Parking in an Emergency ............................................................. 7-2Parking in an Emergency .......................................................... 7-2
Flat Tire ......................................................................................... 7-3 Spare Tire and Tool Storage ...................................................... 7-3
Changing a Flat Tire ................................................................. 7-5
Overheating ................................................................................. 7-11 Overheating ............................................................................. 7-11
Emergency Starting .................................................................... 7-13 Starting a Flooded Engine ....................................................... 7-13
Jump-Starting .......................................................................... 7-13
Push-Starting ........................................................................... 7-15
Emergency Towing ..................................................................... 7-16 Towing Description ................................................................. 7-16
Tiedown Hooks ....................................................................... 7-17
Recreational Towing ............................................................... 7-17
7-1
MX-5 Miata_8T72-EA-04G_Edition2 Page199
Tuesday, August 31 2004 11:25 AM
Form No.8T72-EA-04G
Page 209 of 298
Black plate (209,1)
Overheating
If the temperature gauge indicates
overheating, the vehicle loses power, or
you hear a loud knocking or pinging
noise, the engine is probably too hot.
WARNING
Cooling Fan and Engine
Inspection:
Inspecting the engine with the ignition
switch in the ON position is
dangerous. The cooling fan could turn
on unexpectedly even when the engine
isn't running. You could be seriously
injured by the fan. Turn the ignition
switch off and remove the key from the
ignition switch when you inspect the
engine.
Cooling System Cap:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury. Don't remove the cooling
system cap when the engine and
radiator are hot.
Steam from Overheated Engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you. Open the hood
ONLY after steam is no longer
escaping from the engine. If the temperature gauge indicates
overheating:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic transmission in park (P), a manual
transmission in neutral.
Apply the parking brake.
3. Turn off the air conditioner.
4. Check whether coolant or steam is escaping from under the hood or from
the engine compartment.
If steam is coming from the engine
compartment:
Don't go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the hood and start the engine.
If neither coolant nor steam is
escaping:
Open the hood and idle the engine until
it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an Authorized Mazda
Dealer.
5. Make sure the cooling fan is operating, then turn off the engine after the
temperature has decreased.
6. When cool, check the coolant level. If it's low, look for coolant leaks from
the radiator and hoses.
In Case of an Emergency
Overheating
7-11
MX-5 Miata_8T72-EA-04G_Edition2 Page209
Tuesday, August 31 2004 11:25 AM
Form No.8T72-EA-04G
Page 210 of 298
Black plate (210,1)
If you find a leak or other damage, or if
coolant is still leaking:
Stop the engine and call an Authorized
Mazda Dealer.
Cooling system cap
Engine coolant
reservoir
If you find no problems, the engine is
cool, and no leaks are obvious:
Carefully add coolant as required (page
8-18).
CAUTION
If the engine continues to overheat or
frequently overheats, have the cooling
system inspected. The engine could be
seriously damaged unless repairs are
made. Consult an Authorized Mazda
Dealer.
7-12
In Case of an Emergency
Overheating
MX-5 Miata_8T72-EA-04G_Edition2 Page210
Tuesday, August 31 2004 11:25 AM
Form No.8T72-EA-04G
Page 295 of 298
Black plate (295,1)
D
Dimensions ....................................... 10-5
Door Locks ......................................... 3-9
Driving In Flooded Area ................... 4-12
Driving Tips ........................................ 4-8Automatic transmission .............. 5-13
Break-in period ............................ 4-8
Driving in flooded area .............. 4-12
Hazardous driving ........................ 4-9
Money-saving suggestions ........... 4-8
Rocking the vehicle ...................... 4-9
Turbocharged vehicles ............... 4-13
Winter driving ............................ 4-10
E
Emergency Starting ........................... 7-13Flooded engine ........................... 7-13
Jump-starting .............................. 7-13
Push-starting .............................. 7-15
Emergency Towing ........................... 7-16
Emission Control System .................... 4-4
Engine Coolant ....................................... 8-18
Exhaust gas .................................. 4-6
Hood release .............................. 3-18
Oil .............................................. 8-15
Overheating ................................ 7-11
Starting ......................................... 5-3
Engine Compartment Overview ........ 8-14
Engine Coolant Overheating ................................ 7-11
Engine Coolant Temperature
Gauge ................................................ 5-20
Exhaust Gas ........................................ 4-6
Exterior Care ..................................... 8-44
F
Flasher Hazard warning .......................... 5-34
Headlights .................................. 5-29
Flat Tire ............................................... 7-3 Changing ...................................... 7-5
Spare tire and tool storage ............ 7-3
Fluids Classification .............................. 10-4
Owner maintenance ................... 8-12
Fog Lights ......................................... 5-30
Foot Brake .......................................... 5-4
Front seats ........................................... 2-2
Fuel Filler lid and cap ........................ 3-17
Gauge ......................................... 5-20
Requirements ............................... 4-2
Tank capacity ............................. 10-5
Fuses ................................................. 8-38 Panel description ........................ 8-40
Replacement ............................... 8-38
G
Glove Box ......................................... 6-70
H
Hazard Warning Flasher .................... 5-34
Hazardous Driving .............................. 4-9
HeadlightsControl ....................................... 5-29
Flashing ...................................... 5-29
High-low beam .......................... 5-29
On reminder ............................... 5-29
Hood Release .................................... 3-18
Horn .................................................. 5-33
Index
11-3
MX-5 Miata_8T72-EA-04G_Edition2 Page295
Tuesday, August 31 2004 11:25 AM
Form No.8T72-EA-04G