transmission MAZDA MODEL TRIBUTE HEV 2008 Owner's Manual
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2008, Model line: MODEL TRIBUTE HEV, Model: MAZDA MODEL TRIBUTE HEV 2008Pages: 312, PDF Size: 3.68 MB
Page 273 of 312

it from working. Information about your vehicle’s emission system is on
the Vehicle Emission Control Information Decal located on or near the
engine. This decal identifies engine displacement and gives some tune up
specifications.
Please consult yourWarranty Information Booklet for complete
emission warranty information.
On board diagnostics (OBD-II)
Your vehicle is equipped with a computer that monitors the engine’s
emission control system. This system is commonly known as the On
Board Diagnostics System (OBD-II). The OBD-II system protects the
environment by ensuring that your vehicle continues to meet
government emission standards. The OBD-II system also assists your
authorized dealer in properly servicing your vehicle. When the
indicator illuminates, the OBD-II system has detected a malfunction.
Temporary malfunctions may cause the
indicator to illuminate.
Examples are:
1. The vehicle has run out of fuel—the engine may misfire or run poorly.
2. Poor fuel quality or water in the fuel—the engine may misfire or run poorly.
3. The fuel cap may not have been securely tightened. See Fuel filler
cap in this chapter.
4. Driving through deep water—the electrical system may be wet.
These temporary malfunctions can be corrected by filling the fuel tank
with good quality fuel, properly tightening the fuel cap or letting the
electrical system dry out. After three driving cycles without these or any
other temporary malfunctions present, the
indicator should stay off
the next time the engine is started. A driving cycle consists of a cold
engine startup followed by mixed city/highway driving. No additional
vehicle service is required.
If the
indicator remains on, have your vehicle serviced at the first
available opportunity. Although some malfunctions detected by the
OBD-II may not have symptoms that are apparent, continued driving
with the
indicator on can result in increased emissions, lower fuel
economy, reduced engine and transmission smoothness, and lead to more
costly repairs.
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
273
Page 274 of 312

Readiness for Inspection/Maintenance (I/M) testing
Some state/provincial and local governments may have
Inspection/Maintenance (I/M) programs to inspect the emission control
equipment on your vehicle. Failure to pass this inspection could prevent
you from getting a vehicle registration. Your vehicle may not pass the I/M
test if the
indicator is on or not working properly (bulb is burned
out), or if the OBD-II system has determined that some of the emission
control systems have not been properly checked. In this case, the vehicle
is considered not ready for I/M testing.
If the
indicator is on or the bulb does not work, the vehicle may
need to be serviced. Refer to the On board diagnostics (OBD-II)
description in this chapter.
If the vehicle’s engine or transmission has just been serviced, or the
battery has recently run down or been replaced, the OBD-II system may
indicate that the vehicle is not ready for I/M testing. To determine if the
vehicle is ready for I/M testing, turn the ignition key to the ON position
for 15 seconds without cranking the engine. If the
indicator blinks
eight times, it means that the vehicle is not ready for I/M testing; if
the
indicator stays on solid, it means that the vehicle is ready for
I/M testing.
The OBD-II system is designed to check the emission control system
during normal driving. A complete check may take several days. If the
vehicle is not ready for I/M testing, the following driving cycle consisting
of mixed city and highway driving may be performed:
15 minutes of steady driving on an expressway/highway followed by 20
minutes of stop-and-go driving with at least four 30-second idle periods.
Allow the vehicle to sit for at least eight hours without starting the
engine. Then, start the engine and complete the above driving cycle. The
engine must warm up to its normal operating temperature. Once started,
do not turn off the engine until the above driving cycle is complete. If
the vehicle is still not ready for I/M testing, the above driving cycle will
have to be repeated.
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
274
Page 276 of 312

Note:The brake system on this vehicle can only be bled at a authorized
dealer.
TRANSMISSION FLUID
Checking electronically controlled continuously variable
transmission (eCVT)
Refer to your scheduled maintenance information chapter for
scheduled intervals for fluid checks and changes. Your transaxle does not
consume fluid. It is designed to be filled for life. However, the fluid level
should be checked if you notice some sign of fluid leakage.
Automatic transmission fluid expands when warmed. To obtain an
accurate fluid check, drive the vehicle until it is warmed up
(approximately 20 miles [30 km]). If your vehicle has been
operated for an extended period at high speeds, in city traffic
during hot weather or pulling a trailer, the vehicle should be
turned off for about 30 minutes to allow fluid to cool before
checking.
1. Drive the vehicle 20 miles (30 km) or until it reaches normal operating temperature.
2. Park the vehicle on a level surface and engage the parking brake.
3. With the parking brake engaged and your foot on the brake
pedal, turn the key to the
ACCESSORY position but do not
start the engine. Turn the wheel
to the left to gain access to the
check plug.
4. Latch the gearshift lever in P (Park) and make sure that the engine is OFF by placing the ignition in the Lock position.
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
276
Page 277 of 312

5. Using the hole in the splashshield, remove the check plug
from the side of the
transmission.
If this is the first check of the
transmission fluid, it may be
necessary to remove the perforated
section of the splash shield (as
indicated on the splash shield). 6. Be sure the engine has been stopped for at least 3 minutes before performing the fluid level check.
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
277
Page 278 of 312

7. The fluid level should be within1/4 inch (6 mm) of the plug
threads.
8. Replace the check plug.
Adjusting eCVT fluid levels
Before adding any fluid, make sure the correct type is used. The type of
fluid used is indicated in the Maintenance product specifications and
capacities section in this chapter.
Use of a non-approved fluid may cause internal transaxle
component damage.
If the fluid level is low, add fluid through the check port until the level is
correct and fluid begins to run out of the transmission. If an overfill
occurs, excess fluid should be removed by allowing the fluid to run out
of the check port.
A serious overfill condition of transmission fluid may cause
damage.
Do not use supplemental transmission fluid additives, treatments or
cleaning agents. The use of these materials may affect transmission
operation and result in damage to internal transmission components.
AIR FILTER
Refer to scheduled maintenance information for the appropriate
intervals for changing the air filter element.
When changing the air filter element, use only the Mazda air filter
element listed. Refer to Mazda part numbersin this chapter.
WARNING: To reduce the risk of vehicle damage and/or
personal burn injuries do not start your engine with the air
cleaner removed and do not remove it while the engine is
running.
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
278
Page 282 of 312

ItemCapacityMazda Part Name or
equivalent Application
Fuel tank 15 gallons (56.8L) — All
1Add the coolant type originally equipped in your vehicle. Refer to Adding engine coolantin this
chapter.2Indicates only approximate dry-fill capacity.3Using any transmission fluid other than those that meet the recommended specification may cause
internal transaxle damage. Do not use MERCON CVT (blue) ATF. This vehicle uses only
MERCON V ATF.4Fill to 1/4 inch to 9/16 inch (6mm to 14mm) below bottom of fill hole.54WD vehicles exposed for prolonged periods to temperatures less than -40° C (-40° F) should
change out the rear axle fluid to SAE 75W-140 axle lubricant.6The Power Transfer Unit is lubricated for life with synthetic lube. Lubricant levels are not to be
checked or changed unless a leak is suspected or repair required. Replace Power Transfer Unit
lubricant with specified synthetic lubricant anytime the unit is submerged in water.
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
282
Page 285 of 312

The Vehicle Identification Number (VIN) contains the following
information:1. World manufacturer identifier
2. Brake system / Gross Vehicle Weight Rating (GVWR) /
Restraint System
3. Vehicle line, series, body type
4. Engine type
5. Check digit
6. Model year
7. Assembly plant
8. Production sequence number
TRANSMISSION/TRANSAXLE CODE DESIGNATIONS
You can find a
transmission/transaxle code on the
Safety Compliance Certification
Label . The following table tells you
which transmission or transaxle
each code represents.
Description Code
Electronically controlled continuously variable
transmission, eCVT H
MFD. BY FORD MOTOR CO. IN U.S.A.
EXT PNT:
XX RC: XXDSO:
WB BRK INT TR TP/PS R AXLE TR SPR XXXXX
XXX X XX X XX X XX \
XXX
XXXXXXXXXXXXX XXX XXXX-XXXXXXX-XX
THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR
VEHICLE SAFETY AND THEFT PREVENTION STANDARDS IN
EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE.
VIN: XXXXXXXXXXXXXXXXX XXXXX
TYPE: XXX XXXXX
DATE: XX/XX GVWR:XXXXXLB/ XXXXXKG
FRONT GAWR: XXXXL REAR GAWR: XXXXLB
AT XXX kPa/XX PSI COLD AT XXX kPa/XX PSI COLD XXXXKG
WITH
XXXX/XXXXXXX TIRES
XXXX.XX RIMSXXXXKG
WITH
XXXX/XXXXXXX TIRES
XXXX.XX RIMS
FOR MAZDA MOTOR CORPORATION
2008 Tribute Hybrid(thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
285
Page 289 of 312

Genuine Mazda Parts and Service
When planning your maintenance services, consider your Mazda
dealership for all your vehicle’s needs.
Get the most from your service and maintenance visits
There are a lot of reasons why visiting your Mazda Dealership for all
your service needs is a great way to help keep your vehicle running
great.
Convenience
Many Dealerships have extended evening and Saturday hours to make
your service visit more convenient. How’s that for quality service?
Factory-trained Technicians
Mazda service technicians participate in extensive factory-sponsored
certification training to help them become experts on the operation of
your vehicle. Ask your Dealership about the training and certification
their technicians have received.
Factory Authorized Systems Checks
In the event your vehicle experiences a component related concern,
please contact your Mazda dealership. The Mazda Motor Corporation
Trained Technicians who work at Mazda dealerships are specifically
trained to understand your vehicle.
A proper repair begins with a thorough system check. Factory
Authorized Systems Checks can ONLY be found at a Mazda dealership. In
some circumstances, the Technician may need to request your
authorization to perform additional operations to determine the final
diagnosis. The Technician’s goal is to ensure that your vehicle is fixed
right the first time, at the best value to you.
The following list represents several of the Factory Authorized Systems
Checks available at participating Mazda Dealerships:
•Climate Control
• Check Engine Light
• All Wheel Drive/Four-Wheel Drive
• Automatic Transmission
• Engine Cooling/Cabin Heating
• Suspension/Steering
• Charge/Start/Battery
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Service Maintenance Section
289
Page 303 of 312

A
Accessory delay ..........................65
Air cleaner filter ...............278–280
Air conditioningautomatic temperature
control system ..........................42
Airbag supplemental restraint
system ........................120, 129, 131 and child safety seats ............122
description ..............120, 129, 131
disposal ....................................135
driver airbag ............122, 130, 133
indicator light .........128, 131, 134
operation .................122, 130, 133
passenger airbag .....122, 130, 133
side airbag ...............................129
All Wheel Drive (AWD),
driving off road .........................194
Ambulance packages ..................15
Anti-lock brake system
(see Brakes) ......................187–188
Anti-theft system ........................93
Audio system (see Radio) .........27
Automatic transaxle fluid, adding ............................276
fluid, checking ........................276
Automatic transmission driving an automatic
overdrive .................................193
fluid, refill capacities ..............281
fluid, specification ..................281
Auxiliary input jack (Line in) ....35
Auxiliary power point .................61
Axle lubricant specifications ..........281
refill capacities ........................281
B
Battery .......................................256 acid, treating emergencies .....256
jumping a disabled
battery .............................222, 227
maintenance-free ....................256
servicing ..................................256
Belt-Minder .............................115
Booster seats .............................136
Brakes ........................................187 anti-lock ...........................187–188
anti-lock brake system (ABS)
warning light ...........................188
fluid, checking and adding ....275
fluid, refill capacities ..............281
fluid, specifications .................281
lubricant specifications ..........281
parking ....................................189
shift interlock ..........................191
Bulbs ............................................53
C
Capacities for refilling fluids ....281
Cargo area shade ........................83
Cell phone warning ...................286
Child safety restraints ..............136 child seat belts .......................136
Child safety seats ......................139 attaching with tether straps ..143
in front seat ............................140
in rear seat ..............................140
Child safety seats - booster
seats ...........................................136
Cleaning your vehicle engine compartment ..............243
instrument panel ....................245
interior .....................................245
Mazda car care products .......246
plastic parts ............................244
washing ....................................242
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Index
303
Page 304 of 312

waxing .....................................242
wheels ......................................243
wiper blades ............................244
Climate control (see Air
conditioning or Heating) ............42
Compass, electronic ....................66 calibration .................................67
set zone adjustment .................66
Console ........................................60
Controls power seat .................................99
steering column ........................72
Coolant checking and adding ......258–260
refill capacities ................263, 281
specifications ..........................281
Cruise control .............................69
Cruise control
(see Speed control) ....................69
Customer
Assistance ..................231–232, 235
D
Daytime running lamps
(see Lamps) ................................49
Dipstick automatic transmission
fluid ..........................................276
engine oil .................................253
Driving under special
conditions ..................194, 196, 199 sand .........................................197
snow and ice ...........................200
through water .................198, 201
E
Electronic message center .........74 Emergencies, roadside
jump-starting ..................222, 227
Emission control system ..........272
Engine ........................................283 cleaning ...................................243
idle speed control ...................256
lubrication specifications .......281
refill capacities ........................281
service points ..........................250
Engine oil ..................................253 checking and adding ..............253
dipstick ....................................253
filter, specifications ................255
recommendations ...................255
refill capacities ........................281
specifications ..........................281
Event data recording ..................14
Exhaust fumes ..........................185
F
Fluid capacities .........................281
Foglamps .....................................48
Four-Wheel Drive vehicles driving off road .......................195
preparing to drive your
vehicle .....................................190
Fuel ............................................264 calculating fuel
economy ............................75, 269
cap ...........................................266
capacity ...................................281
choosing the right fuel ...........267
comparisons with EPA fuel
economy estimates .................271
detergent in fuel .....................268
filling your vehicle
with fuel ..................264, 266, 269
filter, specifications ................264
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Index
304