ignition MAZDA MX5 MIATA 2017 Owners Manual

6 –33 Maintenance and Care
Owner Maintenance
Wiper BladesCAUTION 
Hot waxes applied by automatic car
washers have been known to affect the
wiper's ability to clean windows. 
To prevent damage to the wiper blades,
do not use gasoline, kerosene, paint
thinner, or other solvents on or near
them. 
When the wiper lever is in the AUTO
position and the ignition is switched ON,
the wipers may move automatically in
the following cases: 
If the windshield above the rain
sensor is touched. 
If the windshield above the rain
sensor is wiped with a cloth. 
If the windshield is struck with a hand
or other object. 
If the rain sensor is struck with a hand
or other object from inside the vehicle.
Be careful not to pinch hands or fingers
as it may cause injury, or damage the
wipers. When washing or servicing the
vehicle, make sure the wiper lever is in
the OFF position.
Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary. Replacing Windshield Wiper
Blades When the wipers no longer clean well, the
blades are probably worn or cracked.
Replace them.
CAUTION To prevent damage to the wiper arms
and other components, do not try to
sweep the wiper arm by hand.
NOTE
When raising both windshield wiper arms,
raise the driver's side wiper arm first.
When lowering the wiper arms, slowly
lower the wiper arm from the passenger's
side first while supporting it with your
hand. Forcefully lowering the wiper arms
could damage the wiper arm and blade,
and may scratch or crack the windshield.
(Type A)
1. Raise the wiper arm.
2. Open the clip and slide the blade
assembly in the direction of the arrow.
MX-5_8FR4-EA-16J_Edition1.indb 33 2016/08/11 20:29:44

6 –46 Maintenance and Care
Owner Maintenance
CAUTION When removing the lens or lamp unit
using a flathead screwdriver, make
sure that the flathead screwdriver does
not contact the interior terminal. If
the flathead screwdriver contacts the
terminal, a short circuit may occur.
NOTE 
To replace the bulb, contact an
Authorized Mazda Dealer. 
Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.
Replacing Exterior Light BulbsHeadlights, Daytime running lights
(LED type), Parking lights, High-mount
brake light, Brake lights, Taillights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary. Daytime running lights (Bulb type)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the center of each plastic retainer
and remove the retainers.
Rem ova l
Installation
3. Turn the screw counterclockwise and
remove it, and then partially peel back
the mudguard.

4. Turn the socket and bulb assembly
counterclockwise and remove it.
MX-5_8FR4-EA-16J_Edition1.indb 46 2016/08/11 20:29:48

6 –47 Maintenance and Care
Owner Maintenance5. Disconnect the bulb from the socket.

6. Install the new bulb in the reverse order
of the removal procedure.
Front side-marker lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Rem ova l
Installation
4. Turn the socket and bulb assembly
counterclockwise and remove it. 5. Disconnect the bulb from the socket.

6. Install the new bulb in the reverse order
of the removal procedure.
Front turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Rem ova l
Installation
MX-5_8FR4-EA-16J_Edition1.indb 47 2016/08/11 20:29:48

6 –48 Maintenance and Care
Owner Maintenance 4. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector rearward.

5. Turn the socket and bulb assembly
counterclockwise and remove it.
6. Disconnect the bulb from the socket.

7. Install the new bulb in the reverse order
of the removal procedure.
Side turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left. 3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Rem ova l
Installation
4. Remove the unit by pressing the tab on
the unit with your finger and pulling the
unit forward.

5. Detach the electrical connector from
the unit by pulling it to the rear.

6. Install the new side turn signal unit
in the reverse order of the removal
procedure.
MX-5_8FR4-EA-16J_Edition1.indb 48 2016/08/11 20:29:48

6 –49 Maintenance and Care
Owner MaintenanceRear turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the center of each plastic retainer
and remove the retainers and the trunk
end trim.

Rem ova l
Installation
3. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector downward.
4. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the trunk side trim.
Rem ova l
Installation
MX-5_8FR4-EA-16J_Edition1.indb 49 2016/08/11 20:29:48

6 –52 Maintenance and Care
Owner Maintenance Rear side-marker lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.

4. Install the new bulb in the reverse order
of the removal procedure. Reverse lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.

4. Install the new bulb in the reverse order
of the removal procedure.
License plate lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the unit by pressing the tab on
the unit with your finger and pulling the
unit downward.

3. Turn the socket and bulb assembly
counterclockwise and remove it.
MX-5_8FR4-EA-16J_Edition1.indb 52 2016/08/11 20:29:49

6 –54 Maintenance and Care
Owner Maintenance
FusesYour vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls do
not work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
Fuse ReplacementReplacing the fuses on the vehicle's left
side
If the electrical system does not work, first
inspect the fuses on the vehicle's left side.
1. Make sure the ignition is switched off,
and other switches are off.
2. Open the fuse panel cover. 3. Pull the fuse straight out with the
fuse puller provided on the fuse block
located in the engine compartment.
4. Inspect the fuse and replace it if it is
blown.
Normal Blown
5. Insert a new fuse of the same amperage
rating, and make sure it fits tightly. If
it does not fit tightly, have an expert
install it. We recommend an Authorized
Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or OUTLET circuit.
CAUTION Always replace a fuse with a genuine
Mazda fuse or equivalent of the same
rating. Otherwise you may damage
the electric system.
6. Reinstall the cover and make sure that
it is securely installed.
MX-5_8FR4-EA-16J_Edition1.indb 54 2016/08/11 20:29:49

6 –55 Maintenance and Care
Owner MaintenanceReplacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.
NOTE
If the lock is forcefully opened, the fuse
block cover may come in contact with the
frame when it is removed and become
scratched.
When removing the cover, remove it slowly
according to the following procedure.
1. Disengage the rear lock by pressing
down on the front tab with your
fingers.
2. Remove the front tab while slightly
lifting the front of the cover. 3. Remove the cover while lifting it and
sliding it to the rear.
3. If any fuse but the MAIN fuse is
blown, replace it with a new one of the
same amperage rating .
Normal
Blown
WARNING Do not replace the main fuse and
multiplex slow blow fuse by yourself.
Have an Authorized Mazda Dealer
perform the replacement:
Replacing these fuses by yourself is
dangerous because they are high
current fuses. Incorrect replacement
could cause an electrical shock or a
short circuit resulting in a fire.
4. Reinstall the cover and make sure that
it is securely installed.
MX-5_8FR4-EA-16J_Edition1.indb 55 2016/08/11 20:29:49

6 –61 Maintenance and Care
Appearance Care Maintaining the FinishWashing
CAUTION 
When the wiper lever is in the
position and the ignition is switched ON,
the wipers may move automatically in
the following cases: 
If the windshield above the rain
sensor is touched or wiped with a
cloth. 
If the windshield is struck with a hand
or other object from either outside or
inside the vehicle.
Keep hands and scrapers clear of the
windshield when the wiper lever is in the
position and the ignition is
switched ON as fingers could be pinched
or the wipers and wiper blades damaged
when the wipers activate automatically.
If you are going to clean the windshield,
be sure the wipers are turned off
completely (when it is most likely
that the engine is left running) this is
particularly important when clearing ice
and snow. 
Do not spray water in the engine
compartment. Otherwise, it could result
in engine-starting problems or damage
to electrical parts. 
When washing and waxing the vehicle,
be careful not to apply excessive force
to any single area of the vehicle hood.
Otherwise, you could dent the vehicle. 
Do not use automatic car washing
machines and car washing devices using
high water pressure. 
Make sure that the fuel lid is closed
and lock the doors. Otherwise, the fuel
lid may be forcefully opened by water
pressure causing damage to the vehicle
or fuel lid.
To help protect the finish from rust
and deterioration, wash your Mazda
thoroughly and frequently, at least once a
month, with lukewarm or cold water.
If the vehicle is washed improperly, the
paint surface could be scratched. Here are
some examples of how scratching could
occur.
Scratches occur on the paint surface when: 
The vehicle is washed without first
rinsing off dirt and other foreign matter. 
The vehicle is washed with a rough, dry,
or dirty cloth. 
The vehicle is washed at a car wash that
uses brushes that are dirty or too stiff. 
Cleansers or wax containing abrasives
are used.
NOTE 
Mazda is not responsible for scratches
caused by automatic car washes or
improper washing. 
Scratches are more noticeable on
vehicles with darker paint finishes.
MX-5_8FR4-EA-16J_Edition1.indb 61 2016/08/11 20:29:51

6 –67 Maintenance and Care
Appearance Care1. Continue pressing the retractable
fastback switch in the open direction
until the rear roof is raised up from the
fully closed position.
Refer to Opening the Roof on page
3 - 45 .
2. Remove your finger from the
retractable fastback switch after the
rear roof is raised up.
3. Make sure the drainage outlets are
visible.

Drainage
outlet
Rear roof links
4. Switch the ignition OFF.
WARNING Verify that the ignition is switched off:
Closing the roof with the ignition
not switched off is dangerous as the
motors could turn on suddenly and
cause injury resulting from hands
or fingers being pinched in the
mechanism. 5. Remove leaves and other foreign
matter accumulated in the drainage
outlet.
CAUTION When cleaning the drainage outlets,
be careful not to touch the roof links
or the framework of the rear roof.
Otherwise, you could get injured.
Roof links Rear roof
6. After cleaning is finished, continue
pressing the retractable fastback switch
in the close direction to close the rear
roof.
Refer to Closing the Roof on page
3 - 45 .

MX-5_8FR4-EA-16J_Edition1.indb 67 2016/08/11 20:29:53