instrument cluster MAZDA MX5 MIATA 2017 User Guide

4 –12 When Driving
Instrument Cluster and Display SpeedometerThe speedometer indicates the speed of the
vehicle.
Odometer, Trip Meter and Trip
Meter Selector (Without Multi-
information Display)The display mode can be changed from
odometer to trip meter A to trip meter B
and then back to odometer by pressing the
selector while one of them is displayed.
The selected mode will be displayed.
Press the selectorPress the selector
Press the selectorOdometer
Trip meter
A
Trip meter B Selector NOTE
When the ignition is switched to ACC or
off, the odometer or trip meters cannot be
displayed, however, pressing the selector
can inadvertently switch the trip meters or
reset them during an approximate ten-
minute period in the following cases: 
After the ignition is switched to off from
ON. 
After the driver's door is opened.
Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The trip meter can record the total distance
of two trips. One is recorded in trip meter
A, and the other is recorded in trip meter
B.
For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is filled.
When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.
The trip meter records the total distance
the vehicle is driven until the meter
is again reset. Return it to “0.0” by
depressing and holding the selector for
one second or more. Use this meter to
measure trip distances and to compute fuel
consumption.
MX-5_8FR4-EA-16J_Edition1.indb 12 2016/08/11 20:28:43

4 –13 When Driving
Instrument Cluster and DisplayNOTE 
(Vehicles with type B audio)
If the fuel economy data is reset using
the fuel economy monitor, or trip A
is reset using the trip meter when the
function which synchronizes the fuel
economy monitor and the trip meter is
on, the fuel economy data and trip A are
reset simultaneously.
Refer to Fuel Economy Monitor on page
4-69 . 
Only the trip meters record tenths of
kilometers (miles). 
The trip record will be erased when: 
The power supply is interrupted
(blown fuse or the battery is
disconnected). 
The vehicle is driven over 9999.9 km
(mile).
TachometerThe tachometer shows engine speed in
thousands of revolutions per minute (rpm).
CAUTION Do not run the engine with the
tachometer needle in the RED ZONE.
This may cause severe engine damage. Striped zone
Red zone NOTE
When the tachometer needle enters the
STRIPED ZONE, this indicates to the
driver that the gears should be shifted
before entering the RED ZONE.
Engine Coolant Temperature
Gauge (Without Multi-information
Display) Indicates engine coolant temperature.
CAUTION If the high engine coolant temperature
warning light (red) turns on, there is
a possibility of overheating. Park the
vehicle in a safe place immediately
and take appropriate measures. If the
vehicle continues to be driven, it could
cause damage to the engine.
Refer to Overheating on page 7-27 .
MX-5_8FR4-EA-16J_Edition1.indb 13 2016/08/11 20:28:44

4 –14 When Driving
Instrument Cluster and Display NOTE 
The temperature unit (Centigrade/
Fahrenheit) of the engine coolant gauge
display changes in conjunction with
the temperature unit of the outside
temperature display.
Refer to Personalization Features on
page 9-9 .
During normal driving, the engine
coolant temperature stabilizes at
100 °C (210 °F) or less, and the gauge
indicates a range lower than 100 °C
(210 °F). 
If the engine load increases and the
engine coolant temperature exceeds
100 °C (210 °F), the gauge indicates the
engine coolant temperature. Fuel Gauge (Without Multi-
information Display) The fuel gauge shows approximately
how much fuel is remaining in the tank
when the ignition is switched ON. We
recommend keeping the tank over 1/4 full. Full
1/4 Full
Empty
If the low fuel warning light illuminates or
the fuel level is very low, refuel as soon as
possible.
Refer to Warning Lights on page 4-26 .
NOTE 
After refueling, it may require some
time for the indicator to stabilize. In
addition, the indicator may deviate
while driving on a slope or curve since
the fuel moves in the tank. 
The display indicating a quarter or less
remaining fuel has more segments to
show the remaining fuel level in greater
detail. 
The direction of the arrow ( ) indicates
that the fuel-filler lid is on the left side
of the vehicle.
MX-5_8FR4-EA-16J_Edition1.indb 14 2016/08/11 20:28:44

4 –15 When Driving
Instrument Cluster and Display Dashboard IlluminationWhen the position lights are turned
on with the ignition switched ON,
the brightness of the instrument panel
illumination is dimmed. NOTE
When the position lights are turned on,
the position lights indicator light in the
instrument cluster turns on.
Refer to Headlights on page 4-45 .
The brightness of the instrument cluster
and dashboard illuminations can be
adjusted by rotating the knob. 
The brightness decreases by rotating the
knob to the left. A beep sound will be
heard when the knob has been rotated to
the maximum dim position. 
The brightness increases by rotating the
knob to the right. Dim
Bright Function for cancelling illumination
dimmer
The illumination dimmer can be canceled
by rotating the dashboard illumination
knob to the right until a beep sound is
heard while the instrument cluster is
dimmed with the ignition switched ON.
If the instrument cluster's visibility is
reduced due to glare from surrounding
brightness, cancel the illumination
dimmer.
NOTE 
When the illumination dimmer is
canceled, the instrument cluster cannot
be dimmed even if the position lights are
turned on. 
When the illumination dimmer is
canceled, the screen in the center
display switches to constant display of
the daytime screen.
Outside Temperature Display
(Without Multi-information
Display) When the ignition is switched ON, the
outside temperature is displayed.
NOTE
Under the following conditions, the
outside temperature display may differ
from the actual outside temperature
depending on the surroundings and vehicle
conditions: 
Significantly cold or hot
temperatures. 
Sudden changes in outside
temperature. 
The vehicle is parked. 
The vehicle is driven at low speeds.
MX-5_8FR4-EA-16J_Edition1.indb 15 2016/08/11 20:28:44

4 –16 When Driving
Instrument Cluster and Display
*Some models.Changing the Temperature Unit of the
Outside Temperature Display
The outside temperature unit can be
switched between Celsius and Fahrenheit
using the following procedure.
(Vehicles with Type B)
Settings can be changed by operating the
center display screen.
Refer to Personalization Features on page
9-9 .
(Vehicles without Type B)
1. Press the INFO switch with the ignition
switched off and continue pressing the
INFO switch for 5 seconds or longer
while switching the ignition ON. The
outside temperature display flashes.
2. Press the INFO switch to change the
outside temperature unit.
3. Press and hold the INFO switch for
3 seconds or longer while the outside
temperature display is flashing. The
outside temperature display illuminates.
NOTE
When the temperature unit indicated in the
outside temperature display is changed,
the temperature unit indicated in the
engine coolant gauge display changes in
conjunction with it.
Cruise Control Set Vehicle Speed
Display (Without Multi-
information Display) *
The vehicle speed preset using the cruise
control is displayed. Trip Computer and INFO Switch
(Without Multi-information
Display) The following information can be selected
by pressing the INFO switch with the
ignition switched ON. 
Approximate distance you can travel on
the available fuel 
Average fuel economy 
Current fuel economy 
Average vehicle speed
If you have any problems with your trip
computer, consult an Authorized Mazda
Dealer.
Distance-to-empty mode
This mode displays the approximate
distance you can travel on the remaining
fuel based on the fuel economy.
The distance-to-empty will be calculated
and displayed every second.
MX-5_8FR4-EA-16J_Edition1.indb 16 2016/08/11 20:28:44

4 –17 When Driving
Instrument Cluster and DisplayNOTE 
Even though the distance-to-empty
display may indicate a sufficient amount
of remaining driving distance before
refueling is required, refuel as soon as
possible if the fuel level is very low or
the low fuel warning light illuminates. 
The display may not change unless you
add more than approximately 9 L (2.3
US gal, 1.9 Imp gal) of fuel. 
The distance-to-empty is the
approximate remaining distance the
vehicle can be driven until all the
graduation marks in the fuel gauge
(indicating the remaining fuel supply)
disappear. 
If there is no past fuel economy
information such as after first
purchasing your vehicle or the
information is deleted when the battery
cables are disconnected, the actual
distance-to empty/range may differ from
the amount indicated.
Average fuel economy mode
This mode displays the average fuel
economy by calculating the total fuel
consumption and the total traveled
distance since purchasing the vehicle, re-
connecting the battery after disconnection,
or resetting the data. The average fuel
economy is calculated and displayed every
minute.
To clear the data being displayed, press the
INFO switch for more than 1.5 seconds.
After pressing the INFO switch, - - - L/100
km (- - - mpg) will be displayed for about
1 minute before the fuel economy is
recalculated and displayed. Current fuel economy mode
This mode displays the current fuel
economy by calculating the amount of fuel
consumption and the distance traveled.
Current fuel economy will be calculated
and displayed every 2 seconds.
When you've slowed to about 5 km/h (3
mph), - - - L/100 km (- - - mpg) will be
displayed.
Average vehicle speed mode
This mode displays the average vehicle
speed by calculating the distance and the
time traveled since connecting the battery
or resetting the data.
Average vehicle speed will be calculated
and displayed every 10 seconds.
To clear the data being displayed, press the
INFO switch for more than 1.5 seconds.
After pressing the INFO switch, - - - km/h
(- - - mph) will be displayed for about
1 minute before the vehicle speed is
recalculated and displayed.
MX-5_8FR4-EA-16J_Edition1.indb 17 2016/08/11 20:28:44

4 –18 When Driving
Instrument Cluster and Display
*Some models.Multi-information Display and INFO Switch *
INFO switchMulti-information Display
The multi-information display indicates the following information. 
Odometer 
Trip meter 
Engine coolant temperature gauge 
Fuel gauge 
Outside temperature 
Distance-to-empty 
Average fuel economy 
Current fuel economy 
Maintenance Monitor 
Lane Departure Warning System (LDWS) Display 
Cruise Control Display 
Compass Display 
Roof Operation Display 
Warning message
MX-5_8FR4-EA-16J_Edition1.indb 18 2016/08/11 20:28:45

4 –19 When Driving
Instrument Cluster and DisplayThe screen content changes each time the INFO switch is pressed .
Press the INFO switch Press the INFO switchPress the INFO switch Press the INFO switch
Press the INFO switchEngine Coolant
Temperature Gauge,
Maintenance Monitor,
Outside Temperature,
Odometer, Fuel Gauge Engine Coolant
Temperature Gauge,
Compass,
Distance-to-empty,
Outside Temperature,
Odometer, Fuel GaugeWarning message,
Outside
Temperature,
Odometer, Fuel
GaugeEngine Coolant
Temperature Gauge,
Trip Meter A, Average
Fuel Economy, Current
Fuel Economy, Outside
Temperature,
Odometer, Fuel Gauge
Engine Coolant
Temperature Gauge,
Trip Meter B, Average
Fuel Economy, Current
Fuel Economy, Outside
Temperature,
Odometer, Fuel Gauge *1
*2
*1: Displayed only when a warning occurs.
*2: Displayed only while vehicle is being driven.
MX-5_8FR4-EA-16J_Edition1.indb 19 2016/08/11 20:28:45

4 –20 When Driving
Instrument Cluster and Display Odometer, Trip Meter and Trip
Meter SelectorThe odometer is constantly displayed on
the screen when the ignition is switched
ON, and the TRIP A or TRIP B screen
can be displayed by operating the INFO
switch.
Press the INFO switch INFO switch
Trip meter A,
Odometer
Trip meter B,
Odometer
Odometer
The odometer records the total distance
the vehicle has been driven. Trip meter
The driving distance for a specified
interval is indicated. Two types (TRIP
A, TRIP B) of interval distance and the
average fuel economy for each can be
measured.
For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is filled.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.
The trip meter and average fuel economy
can be reset by pressing the INFO switch
for 1.5 second or more while in each
mode.
NOTE 
Only the trip meters record tenths of
kilometers (miles). 
The trip record will be erased when: 
The power supply is interrupted
(blown fuse or the battery is
disconnected). 
The vehicle is driven over 1999 km
(mile).
MX-5_8FR4-EA-16J_Edition1.indb 20 2016/08/11 20:28:45

4 –21 When Driving
Instrument Cluster and Display Engine Coolant Temperature
GaugeDisplays the engine coolant temperature.
The blue gauge indicates that the engine
coolant temperature is low, and the red
gauge indicates that the engine coolant
temperature is high and overheating.
CAUTION If the high engine coolant temperature
warning light (red) turns on, there is
a possibility of overheating. Park the
vehicle in a safe place immediately
and take appropriate measures. If the
vehicle continues to be driven, it could
cause damage to the engine.
Refer to Overheating on page 7-27 .
NOTE 
The temperature unit (Centigrade/
Fahrenheit) of the engine coolant gauge
display changes in conjunction with
the temperature unit of the outside
temperature display.
Refer to Personalization Features on
page 9-9 .
During normal driving, the engine
coolant temperature stabilizes at
100 °C (210 °F) or less, and the gauge
indicates a range lower than 100 °C
(210 °F). 
If the engine load increases and the
engine coolant temperature exceeds
100 °C (210 °F), the gauge indicates the
engine coolant temperature. Fuel Gauge The fuel gauge shows approximately
how much fuel is remaining in the tank
when the ignition is switched ON. We
recommend keeping the tank over 1/4 full. Full
1/4 Full
Empty
If the fuel level is low, ( ) and ( ) turn an
amber color. Refuel as soon as possible.
Refer to Taking Action on page 7-41 .
NOTE 
After refueling, it may require some
time for the indicator to stabilize. In
addition, the indicator may deviate
while driving on a slope or curve since
the fuel moves in the tank. 
The display indicating a quarter or less
remaining fuel has more segments to
show the remaining fuel level in greater
detail. 
The direction of the arrow ( ) indicates
that the fuel-filler lid is on the left side
of the vehicle.
MX-5_8FR4-EA-16J_Edition1.indb 21 2016/08/11 20:28:46