light MERCEDES-BENZ A-CLASS SALOON 2021 Repair Manual

R
Has been inspec tedby aqu ali/ed elect ri-
cian #
For saf etyre asons, only use thech arging
cable supplied with theve hicle or an
original Mercedes-Benz charging cable. #
Purchase these parts at a Mercedes-
Benz Service Centre and obtain advice
th ere.
Mercedes-Benz thoroughly tests these original
ch arging cables forth eir suitability for high-
vo ltage charging of your vehicle. #
Never use a damaged charging cable. #
Do not use:
R Extension cables
R Extension reels
R Multiple soc kets #
Never use soc ket ada pters toconnect
th ech arging cable tothe mains soc ket.
The only exception being if the adap ter
has been tested and appro vedby the manufacturer
forch arging the high-volt-
age battery of an electric vehicle. #
Obser vethe saf ety no tes in the operat-
ing inst ructions forth e soc ket ada pter. Only
thefo llowing charging cables may be used:
R The charging cable supplied with theve hicle.
R Ach arging cable that has been appr ovedfor
th eve hicle.
The charging process can vary depending on the
po we r supply equipment.
Shor terch arging times can be achie ved in thefo l-
lowing ways:
R Charging at a wallbox.
R Charging at a charging station.
When doing so, alw ays obser vethe local informa-
tion.
Do not lea vethech arging cable cont rols hanging
loose from a mains soc ket. Do not liT
the controls bythefo llowing compo-
nent parts:
R The charging cable connector.
R The mains plug.
When charging, pr otect thech arging cable cont rol
element from excessive heat such as direct sun-
light. Otherwise, thech arging process may be
cancelled. N No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery at a
y at a
w
w allbo
allbo x or c
x or c har
har ging st
ging st ation (mode 3)
ation (mode 3) &
D
DAN
AN GER
GER Risk of fatal injury from incor-
re ctly ins talled component parts
Connecting thech arging cable toawa llbox
using incor rectly ins talled component parts
could cause a /re or an electric shoc k,for
ex ample. #
Only connect thech arging cable to a
wa llbox that:
R Has been proper lyinstalled and Driving and parking
191
191

ity
for high-voltage charging of your vehi-
cle. Pur chase these parts at a Mercedes-
Benz Service Centre and obtain advice
th ere. #
Check the setting of the maximum
ch arge cur rent using thech arging capa-
city shown in the Instrument Displa y.Before
charging at a mains soc ket, ha vethe maxi-
mum permissible charging cur rent forth ere leva nt
mains soc ket or the building inspected byaqu ali-
/ed elect rician. The charging cable supplied is set
to a countr y-speci/c maximum charging cur rent
va lue. When charging abroad, the maximum value
may exceed the permitted value forth at countr y.
When abroad, obser vethe count ry-speci/c la ws
when charging. If you ha vequestions concerning
setting thech arging cur rent or if there is a mal-
function, please contact a quali/ed specialist
wo rkshop. #
Set the maximum permissible charging cur-
re nt in the multimedia system menu
(/ page 292). If
th eex act value of the maximum permissible
ch arging cur rent cannot be set, select the next
smaller adjustable value.
% Ifth eve hicle requ ires more time than usual to
ch arge the high-voltage batter y,ch eck the
maximum charging cur rent settings in the
multimedia system menu. Ov Ov
er
ervie
vie w of t
w of t he c
he char
harging cable contr
ging cable contr ol panel
ol panel The
charging cable cont rol panel sho ws the cur-
re nt status of thech arging process. 1
Supply voltage indicator
2 Charging process indicator 3
Temp erature monitor indicator
4 Safety sy stem indicator
Suppl
Suppl y v
y volt
oltag
age indicat
e indicat or
or1
1 Display
Display
Meaning
Meaning
Lights up whit eThe supplyvoltage is
connected. Char
Char
ging pr
ging pr ocess indicat
ocess indicat or
or2
2 Display Display
Meaning Meaning
Flashes green The high-voltage bat-
tery isch arging. 194
194
Driving and parking

T
T
em
em per
per atur
atur e contr
e contr ol indicat
ol indicat or
or3
3 Display
Display
Meaning
Meaning
Lights up redT hegreen LED 0ashes
simultaneousl y:ove r-
te mp erature – the
ch arging per form ance
is reduced.
The green LED does
not 0ash: overtemper-
ature – thech arging
process is stopped.
Flashes redO vertemperature at
th e mains plug – the
ch arging process is
stopped. Safe
Safe
ty syst
ty syst em indicat
em indicat or
or4
4 Displ
ay
Display Meaning
Meaning
Flashes redC harging cable mal-
function – cann ot
car ryout thech arging
process, reset the
ch arging cable operat-
ing unit.
Lights up redW hite LED is o.:
po we r supply malfunc-
tion – cannot car ry
out thech arging proc-
ess, replace the mains
soc ket.
White LED is on: vehi-
cle malfunction – can-
not car ryout the
ch arging process,
re set thech arging
cable operating unit. When all
four displa yslight up, thech arging cable
operating unit per form s a self-test. If
te mp erature monitor 3indicates a malfunc-
tion, it may help toprotect thech arging cable
from direct sunlight.
T T o r
o r ese
ese t t
t the c
he c har
harging cable oper
ging cable oper ating unit:
ating unit:if
saf ety sy stem 4indicates a charging cable mal-
function or a vehicle malfunction, /rst reset the
ch arging cable operating unit. Todo this, discon-
nect thech arging cable from theve hicle and from
th e mains soc ket and waitfor appr oximately /ve
seconds. If the malfunction persists aTer the
ch arging cable is reconnected, charging at the
mains soc ket is not possible. The charging cable
must be replaced or theve hicle plug must be
ch ecked at a quali/ed specialist workshop,
depending on the indicator. F
F
unctions of t
unctions of t he indicat
he indicator lam
or lamps on t
ps on t he v
he vehicle
ehicle
soc ket
soc ket %
Depending on the national version, your vehi-
cle is equipped with one of thefo llowing vehi-
cle soc kets.
The soc ket 0ap is centrally loc ked and unloc ked
to get her with theve hicle. Driving and parking
195
195

Combo 1
vehicle soc ket
1 Socket lamp
2 Charging process indicator lamp
3 Locking status indicator lamp Combo 2
vehicle soc ket
1 Socket lamp
2 Charging process indicator lamp
3 Locking status indicator lamp
Soc ket lamp 10ashes or lights up as with indi-
cator lamps 2and 3. Ov
Ov
er
ervie
vie w of t
w of t he loc
he loc king st
king st atus
atus Loc
Loc
king st
king st a-
a-
tus
tus 3
3 Display
Display
Meaning
Meaning
% Lights up
white Ve
hicle
soc ket
unloc ked,
insert or
re mo vecharg-
ing cable
% Flashes whiteMalfunction
during locking
or unlocking Ov Ov
er
ervie
vie w of t
w of t he c
he char
harging pr
ging pr ocess st
ocess st atus
atus S
S
t
tatus of t
atus of t he
he
c
c har
har ging
ging
pr
pr ocess
ocess 2
2 Displ
ay
Display Meaning
Meaning
# Flashes
orangeConnection is
being estab-
lished
# Flashesgreen Active energy
0ow 196 196
Driving and parking

S
S
t
tatus of t
atus of t he
he
c
c har
har ging
ging
pr
pr ocess
ocess 2
2 Displ
ay
Display Meaning
Meaning
# Lights up
orangeInter
ruption in
ch arging
# Lights up
green Charging
process com-
ple
ted
# Flashesred
(for appr ox.
90 s) Ve
hicle mal-
function;
ch arging is
not possible S S
t
tar
ar ting t
ting t he alt
he alt er
ernating curr
nating curr ent c
ent char
harging pr
ging pr ocess
ocess
(mode 2/3)
(mode 2/3) &
D
DAN
AN GER
GER Risk of death when charging at a
damaged soc ket
The charging process uses high voltage. If
th ech arging cable, theve hicle soc ket or the
mains soc ket are damaged, you could receive
an elect ric shoc k. #
Only use an undamaged charging cable. #
Avoid mechanical damage such as crush-
ing, abrading or driving overth e cable. #
Have a damaged vehicle soc ketre placed
at a quali/ed specialist workshop as
soon as possible. #
Never connect thech arging cable to a
damaged vehicle soc ket. *
N
NOOTE
TE Damage due toove rheating of
ch arging cable and charging cable con-
nector During
thech arging process, thech arging
cable and charging cable connector can heat
up within their permissible limit values. The permissible limit
values are in0uenced by
th efo llowing factors:
R the po wer supply system and thech arging
cable are not damaged
R the inst ructions for handling thech arging
cable and the control element on the
ch arging cable ha vebeen obser ved #
Ifth ech arging cable or charging cable
connector becomes too hot, ha vethe
po we r supply system checked. *
N NOOTE TE Damaged or dirty vehicle soc ket
when the soc ket 0ap is open #
Alwayske ep the soc ket co ver and the
soc ket 0ap closed when there is no
ch arging cable connected. This pr otects
th eve hicle soc ket from dirt and damage. #
Make sure that the soc ket co ver is
closed proper lybefore closing the soc ket
0ap. This can otherwise result in damage
which may pr event the soc ket 0ap from
being opened again. Driving and parking
197
197

Combo 2
vehicle soc ket #
Press the centre rear section of soc ket 0ap
1 and swing the soc ket 0ap forw ards and
open.
The % indicator lamp 2and status dis-
play 3light up white. %
When theve hicle is switched on (the õ
displ ayis lit in the Instrument Display), soc ket
0ap 1cannot be opened. #
Press cat ch7 tothe leT and fold open
soc ket co ver5.
% Vehicles with a vehicle soc ket combo requ ire
only connection 8forth ech arging cable
connector. Open only the upper part of soc ket
co ver5. #
Tocharge at a mains soc ket, insert the mains
plug into the mains soc ket of theex tern al
po we r source tothe stop and set the maxi-
mum charging cur rent if requ ired
(/ page 193). #
Insert thech arging cable connector into vehi-
cle soc ket connection 8tothe stop. If the
wa llbox/charging station is not equipped with
a ch arging cable, inse rtthe plug of theve hi-
cle's charging cable into thewa llbox/charging
station soc ketto the stop.
Make sure that thech arging cable is not taut
when inser ted. The
# indicator lamp 4and status dis-
play 30ash orange and, as soon as the high-
vo ltage battery is charge d, green.
When thech arging cable is connected totheve hi-
cle, theve hicle cann otbe star ted or mo ved.
At the start of thech arging process, thech arge
le ve l display is shown in the Instrument Display
with a charging prediction. The charging predic-
tion either refers to the predicted charge leve l at
th e set departure time, or the time at which the
high- voltage battery will be fully charge d.
% Depending on thete mp erature, thefa n and
bat tery cooling system may audibly switch on
during thech arging process.
% Ifth eve hicle is idle for lengt hyperiods and
connected tothe mains suppl y,the high-volt-
age battery will be rech arge d automatically as
needed or when electrical consumers are
activated (e.g. the pre-entry climate control). Driving and parking
199 199

%
The vehicle is equipped with an elect rical fuse
which pr otects it against overvoltage in the
mains suppl y.This electrical fuse may trip dur-
ing se vere thunderstorms, forex ample, and
may cause the fuse in the building totrip or
may inter rupt thech arging process. These
functions pr otect theve hicle.
ATer the fuse in the building is switched on
again, thech arging process resumes automat-
icall y.Fo llowing an inter ruption in the po wer
supply without the fuse in the building being
tripped, it may take up to te n minutes for
ch arging toresume automaticall y.Ending t
Ending t
he alt
he alter
ernating curr
nating curr ent c
ent char
harging pr
ging pr ocess
ocess
(mode 2/3)
(mode 2/3) R
R
eq
eq uir
uir ements:
ements:
R The dis tance between theke y and theve hicle
does not exceed 1 m. Combo 1 v
Combo 1 v
ehicle socket
ehicle soc ket #
Press charging inter ruption button 3.
or #
Unlock theve hicle.
The charging process is ended. The %indi-
cator lamp 1lights up white. The vehicle
soc ket is unloc ked. %
Vehicles equipped with a type 1 vehicle
soc ketfo rAC charging ha veno charging inter-
ru ption button 3. #
Press and hold button 2onthech arging
cable connector and remo vethech arging
cable connector from theve hicle soc ket.
% Ifyo u cannot remo vethech arging cable con-
nector, repeat the unlocking procedure. If the
ch arging cable connector is still loc ked, con-
ta ct a quali/ed specialist workshop. #
Close the soc ket co ver and the soc ket 0ap. #
Remo vethech arging cable connector from
th e mains soc ket, or from the soc ket on the
wa llbox/charging station, and st owtheve hi-
cle's charging cable safely in theve hicle
(/ page 188). 200
200
Driving and parking

Combo 2 v
Combo 2 v
ehicle socket
ehicle soc ket #
Press charging inter ruption button 2.
or #
Unlock theve hicle.
The charging process is ended. The %indi-
cator lamp 1lights up white. The vehicle
soc ket is unloc ked. %
Vehicles only equipped with a type 2 vehicle
soc ketfo rAC charging ha veno charging inter-
ru ption button 2. #
Remo vethech arging cable connector from
th eve hicle soc ket within 30 seconds.
ATer the 30 seconds ha veelapsed, theve hicle
soc ket will be loc ked again.
% Ifyo u cannot remo vethech arging cable con-
nector, repeat the unlocking procedure. If the
ch arging cable connector is still loc ked, con-
ta ct a quali/ed specialist workshop. #
Close the soc ket co ver and the soc ket 0ap. #
Remo vethech arging cable connector from
th e mains soc ket, or from the soc ket on the
wa llbox/charging station, and st owtheve hi-
cle's charging cable safely in theve hicle
(/ page 188).
% ATer thech arging cable connector has been
disconnected, the% indicator lamp 1on
th eve hicle soc ketre mains lit for some time
before switching o.. S
S
t
tar
ar ting t
ting t he dir
he dir ect curr
ect curr ent c
ent char
harging pr
ging process ocess
(mode 4)
(mode 4) &
D
DAN
AN GER
GER Risk of death when charging at a
damaged soc ket
The charging process uses high voltage.
If th ech arging cable, theve hicle soc ket or the
mains soc ket are damaged, you could receive
an elect ric shoc k. #
Only use an undamaged charging cable. #
Avoid mechanical damage such as crush-
ing, abrading or driving overth e cable. #
Have a damaged vehicle soc ketre placed
at a quali/ed specialist workshop as
soon as possible. #
Never connect thech arging cable to a
damaged vehicle soc ket. Driving and parking
201
201

Combo 1
vehicle soc ket Combo 2
vehicle soc ket #
Press the centre rear section of soc ket 0ap
1 and swing the soc ket 0ap forw ards and
open.
The % indicator lamp 2and status dis-
play 3light up white. %
When theve hicle is switched on (the õ
displ ayis lit in the Instrument Display), soc ket
0ap 1cannot be opened. #
Press cat ch7 tothe leT and fold open
soc ket co ver5.
% The CCS charging cable connector requ ires
connections 6and 8. Therefore, it is nec-
essary toopen bo thparts of soc ket co ver5. #
Insert the CCS charging cable connector into
th eve hicle soc ketto the stop.
Make sure that thech arging cable is not taut
when inser ted.
The # indicator lamp 4and status dis-
play 30ash orange and, as soon as the high-
vo ltage battery is charge d, green.
When thech arging cable is connected totheve hi-
cle, theve hicle cann otbe star ted or mo ved.
At the start of thech arging process, thech arge
le ve l display is shown in the Instrument Display
with a charging prediction. The charging predic-
tion either refers to the predicted charge leve l at
th e set departure time, or the time at which the
high- voltage battery will be fully charge d. Driving and parking
203 203

%
Depending on thete mp erature, thefa n and
bat tery cooling system may audibly switch on
during thech arging process.
% Ifth eve hicle is idle for lengt hyperiods and
connected tothe mains suppl y,the high-volt-
age battery will be rech arge d automatically as
needed or when electrical consumers are
activated (e.g. the pre-entry climate control). Ending t Ending t
he dir
he direct curr
ect curr ent c
ent c har
harging pr
ging pr ocess (mode
ocess (mode
4)
4) R
R
eq
eq uir
uir ements:
ements:
R The distance between theke y and theve hicle
does not exceed 1 m. Combo 1 v
Combo 1 v
ehicle socket
ehicle soc ket #
Press charging inter ruption button 3.
The charging process is ended. The %indi-
cator lamp 1lights up white. The vehicle
soc ket is unloc ked. #
Press and hold button 2onthech arging
cable connector and remo vethech arging
cable connector from theve hicle soc ket. %
Ifyo u cannot remo vethech arging cable con-
nector, unlock theve hicle and repeat the pro-
cedure. If thech arging cable connector is still
loc ked, contact a quali/ed specialist work-
shop. #
Close the soc ket co ver and the soc ket 0ap.
Combo 2 v
Combo 2 v ehicle socket
ehicle soc ket 204
204
Driving and parking