oil capacity MERCEDES-BENZ AMG GT S 2016 C190 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2016, Model line: AMG GT S, Model: MERCEDES-BENZ AMG GT S 2016 C190Pages: 290, PDF Size: 6.73 MB
Page 10 of 290
DVD videoOperatin g(on-boar dcomputer) .... .158
see also Digital Operator's Man-
ual ..................................................2 00
DYNAMIC SELECT controller ............ 108
E
E-SELECT lever................................... 109
EASY-ENTRY feature
Function/notes ................................ 80
EASY-EXIT feature
Function/notes ................................ 80
EBD (electronic brake force distri-
bution)
Display message ............................ 169
Function/notes ................................ 57
ECO start/stop function
Automatic engine switch-off .......... 105
Deactivating/activating ................. 106
General information ....................... 105
Important safety notes .................. 105
Introduction ................................... 105
Electronic Stability Program
see ESP
®(Electronic Stability Program)
Emergency
Automatic measures after an acci-
dent ................................................. 49
Emergency release
Driver's door ....................................6 8
Vehicle .............................................6 8
Emergency Tensioning Devices
Activation ........................................ .46
Emergency unlocking
Tailgate ............................................ 71
Emissions control
Service and warranty information .... 22
Engine
Check Engine warning lamp ........... 195
Display message ............................ 178
ECO start/stop function ................ 105
Engine number ............................... 281
Irregular running ............................ 107
Jump-starting ................................. 248
Starting problems .......................... 107
Starting the engine with the
SmartKey ....................................... 104 Starting with the Start/Stop but-
ton ................................................. 104
Switching off .................................. 120
Tow-starting (vehicle) ..................... 252
Engine electronics
Notes ............................................. 279
Problem (malfunction) ................... 107
Engine oil
Adding ........................................... 230
Additives ........................................ 284
Checking the oil level ..................... 228
Checking the oil level using the
dipstick .......................................... 228
Checking the oil level using the
on-board computer ........................ 230
Display message ............................ 179
Fill
ing capacity ............................... 284
Notes about oil grades ................... 283
Notes on oil level/consumption .... 228
Temperature (on-board com-
puter) ............................................. 162
Entering an address
see also Digital Operator's Man-
ual .................................................. 200
ESP
®(Electronic Stability Pro-
gram)
AMG menu (on-board computer) ... 163
Characteristics ................................. 56
Deactivating/activating ................... 56
Display message ............................ 167
Function/notes ................................ 55
General notes .................................. 55
Important safety information ........... 56
Warning lamp ................................. 192
ETS/4ETS (Electronic Traction Sys-
tem) ...................................................... 55
Exhaust check ................................... 123
Exhaust pipe (cleaning instruc-
tions) .................................................. 238
Exterior lighting
Cleaning ......................................... 237
see Lights
Exterior mirrors
Adjusting ......................................... 82
Dipping (automatic) ......................... 83
Folding in/out (automatically) ......... 82
Folding in/out (electrically) ............. 82
8Index
Page 19 of 290
Setting (climate control) .................. 96
Transmission oil (on-board com-
puter) ............................................. 162
Timing (RACETIMER) ......................... 164
Tire pressure
Calling up (on-board computer) ..... 260
Checking manually ........................ 260
Display message ............................ 183
Maximum ....................................... 259
Not reached (TIREFIT) .................... 244
Notes ............................................. 258
Reached (TIREFIT) .......................... 244
Recommended ............................... 257
Tire pressure monitor
Checking the tire pressure elec-
tronically ........................................ 261
Function/notes ............................. 260
General notes ................................ 260
Important safety notes .................. 260
Restarting ...................................... 262
Warning lamp ................................. 198
Warning message .......................... 262
Tire-change tool kit ........................... 241
TIREFIT kit .......................................... 242
Important safety notes .................. 242
Storage location ............................ 241
Tire pressure not reached .............. 244
Tire pressure reached .................... 244
Tires
Aspect ratio (definition) ................. 272
Average weight of the vehicle
occupants (definition) .................... 270
Bar (definition) ............................... 270
Changing a wheel .......................... 272
Characteristics .............................. 270
Checking ........................................ 255
Curb weight (definition) ................. 271
Definition of terms ......................... 270
Direction of rotation ...................... 273
Display message ............................ 183
Distribution of the vehicle occu-
pants (definition) ............................ 272
DOT (Department of Transporta-
tion) (definition) ............................. 270
DOT, Tire Identification Number
(TIN) ............................................... 270
GAWR (Gross Axle Weight Rating)
(definition) ..................................... 271 GVW (Gross Vehicle Weight) (def-
inition) ........................................... 271
GVWR (Gross Vehicle Weight Rat-
ing) (definition) .............................. 271
Important safety notes .................. 254
Increased
vehi
cle weight due to
optional equipment (definition) ...... 271
Information on driving .................... 254
Kilopascal (kPa) (definition) ........... 271
Labeling (overview) ........................ 267
Load bearing index (definition) ...... 272
Load index ..................................... 269
Load index (definition) ................... 271
Maximum load on a tire (defini-
tion) ............................................... 271
Maximum loaded vehicle weight
(definition) ..................................... 271
Maximum permissible tire pres-
sure (definition) ............................. 271
Maximum tire load ......................... 269
Maximum tire load (definition) ....... 271
Optional equipment weight (defi-
nition) ............................................ 272
PSI (pounds per square inch) (def-
inition) ........................................... 272
Replacing ....................................... 272
Service life ..................................... 255
Sidewall (definition) ....................... 272
Speed rating (definition) ................ 271
Storing ........................................... 273
Structure and characteristics
(definition) ..................................... 270
Summer tires in winter .................. 256
Temperature .................................. 267
TIN (Tire Identification Number)
(definition) ..................................... 272
Tire bead (definition) ...................... 272
Tire pressure (definition) ................ 272
Tire pressures (recommended) ...... 271
Tire size (data) ............................... 277
Tire size designation, load-bearing
capacity, speed rating .................... 267
Tire tread ....................................... 255
Tire tread (definition) ..................... 272
Total load limit (definition) ............. 272
Traction ......................................... 266
Traction (definition) ....................... 272
Tread wear ..................................... 266
Index17
Page 273 of 290
Uniform Tire Quality Grading Standards
A uniform standard to grade the quality of tires
with regards to tread quality, tire traction and
temperature characteristics. The quality grad-
ing assessment is made by the manufacturer
following specifications from the U.S. govern-
ment. The ratings are molded into the sidewall ofthe tire.
Recommended tire pressures
The recommended tire pressure applies to the
tires mounted at the factory.
The Tire and Loading Information placard con-
tains the recommended tire pressures for cold
tires on a fully loaded vehicle and for the maxi-
mum permissible vehicle speed.
The tire pressure table contains the recommen-
ded pressures for cold tires for various operat-
ing conditions, i.e. differing load and speed con-
ditions.
Increased vehicle weight due to optional
equipment
The combined weight of all standard and
optional equipment available for the vehicle,
regardless of whether it is actually installed on
the vehicle or not.
Rim
This is the part of the wheel on which the tire is
mounted.
GAWR (Gross Axle Weight Rating)
The GAWR is the maximum gross axle weight
rating. The actual load on an axle must never
exceed the gross axle weight rating. The gross
axle weight rating can be found on the vehicle
identification plate on the B-pillar on the driver's
side.
Speed rating
The speed rating is part of the tire identification.
It specifies the speed range for which the tire is
approved.
GVW (Gross Vehicle Weight)
The gross vehicle weight includes the weight of
the vehicle including fuel, tools, the spare wheel,
accessories installed, occupants, luggage and
the drawbar noseweight, if applicable. The gross
vehicle weight must not exceed the gross vehi-
cle weight rating GVWR as specified on the vehi-
cle identification plate on the B-pillar on the
driver's side.
GVWR (Gross Vehicle Weight Rating)
The GVWR is the maximum permissible gross
weight of a fully loaded vehicle (the weight of the
vehicle including all accessories, occupants,
fuel, luggage and the drawbar n
oseweight, if
applicable). The gross vehicle weight rating is
specified on the vehicle identification plate on
the B-pillar on the driver's side.
Maximum loaded vehicle weight
The maximum weight is the sum of:
Rthe curb weight of the vehicle
Rthe weight of the accessories
Rthe load limit
Rthe weight of the factory installed optional
equipment
Kilopascal (kPa)
Metric unit for tire pressure. 6.9 kPa corre-
sponds to 1 psi. Another unit for tire pressure is
bar. 100 kilopascals (kPa) are the equivalent of
1 bar.
Load index
In addition to the load-bearing index, the load
index may also be imprinted on the sidewall of
the tire. This specifies the load-bearing capacity
more precisely.
Curb weight
The weight of a vehicle with standard equipment
including the maximum capacity of fuel, oil and
coolant. It also includes the air-conditioning sys-
tem and optional equipment if these are instal-
led in the vehicle, but does not include passen-
gers or luggage.
Maximum load rating
The maximum tire load is the maximum permis-
sible weight in kilograms or lbs for which a tire is
approved.
Maximum permissible tire pressure
Maximum permissible tire pressure for one tire.
Maximum load on one tire
Maximum load on one tire. This is calculated by dividing the maximum axle load of one axle by
two.
All about wheels and tires271
Wheels and tires
Z
Page 276 of 290
XPlace chocks or other suitable items under
the front and rear of the wheel that is diago-
nally opposite the wheel you wish to change.
Raising the vehicle
GWARNING
If you do not position the jack correctly at the
appropriate jacking point of the vehicle, the
jack could tip over with the vehicle raised.
There is a risk of injury.
Only position the jack at the appropriate jack-
ing point of the vehicle. The base of the jack
must be positioned vertically, directly under
the jacking point of the vehicle.
!The jack is designed exclusively for jacking
up the vehicle at the jacking points. Other-
wise, your vehicle could be damaged.
Observe the following when raising the vehi-
cle:
RTo raise the vehicle, only use the vehicle-spe-
cific jack that has been tested and approved
by Mercedes-Benz. If used incorrectly, the
jack could tip over with the vehicle raised.
RThe jack is designed only to raise and hold the
vehicle for a short time while a wheel is being
changed. It must not be used for performing
maintenance work under the vehicle.
RAvoid changing the wheel on uphill and down-
hill slopes.
RBefore raising the vehicle, secure it from roll-
ing away by applying the parking brake and
inserting wheel chocks. Do not disengage the
parking brake while the vehicle is raised.
RThe jack must be placed on a firm, flat and
non-slip surface. On a loose surface, a large,
flat, load-bearing underlay must be used. On a
slippery surface, a non-slip underlay must be
used, e.g. rubber mats.
RDo not use wooden blocks or similar objects
as a jack underlay. Otherwise, the jack will not be able to achieve its load-bearing capacity
due to the restricted height.
RMake sure that the distance between the
underside of the tires and the ground does not
exceed 1.2 in (3 cm).
RNever place your hands and feet under the
raised vehicle.
RDo not lie under the vehicle.
RDo not start the engine when the vehicle is
raised.
RNever open or close a door or the tailgate
when the vehicle is raised.
RMake sure that no persons are present in the
vehicle when the vehicle is raised.
Vehicles with hub caps: the hub cap covers
the wheel bolts. Before you can unscrew the
wheel bolts, you must remove the hub cap.
XTo remove: take socket;and lug wrench
= from the vehicle tool kit (Ypage 241).
XPosition socket ;on hub cap :.
XPosition lug wrench =on socket ;.
XUsing lug wrench =, turn hub cap:coun-
ter-clockwise and remove it.
XTo install: before installing, check hub cap :
and the wheel area for soiling and clean if
necessary.
XPut hub cap :in position and turn until it is in
the right position.
XPosition socket ;on hub cap :.
XAttach lug wrench =to socket ;and
tighten hub cap :.
The tightening torque must be
18 lb-ft (25 Nm).
iNote that the hub cap should be tightened
to the specified torque of 18 lb-ft (25 Nm).
Mercedes-Benz recommends that you have
the hub cap installed at a qualified specialist
workshop.
274Changing a wheel
Wheels and tires
Page 286 of 290
iMB approval is indicated on the oil contain-
ers.
Filling capacities
The following values refer to an oil change
including the oil filter.
Capacity
All models7.4 US qt (7.0 l)
Additives
!Do not use any additives in the engine oil.
This could damage the engine.
Brake fluid
GWARNING
The brake fluid constantly absorbs moisture
from the air. This lowers the boiling point of
the brake fluid. If the boiling point of the brake
fluid is too low, vapor pockets may form in the
brake system when the brakes are applied
hard. This would impair braking efficiency.
There is a risk of an accident.
You should have the brake fluid renewed at
the specified intervals.
Comply with the important safety notes for ser-
vice products when handling brake fluid
(
Ypage 281).
The brake fluid change intervals can be found in
the Maintenance Booklet.
Only use brake fluid approved by Mercedes-
Benz in accordance with MB-Freigabe or MB-
Approval 331.0.
Information about approved brake fluid can be
obtained at any qualified specialist workshop or on the Internet at
http://bevo.mercedes-benz.co m.
iHave the brake fluid regularly replaced at a
qualified specialist workshop and the replace-
ment confirmed in the Maintenance Booklet.
Coolant
Important safety notes
GWARNING
If antifreeze comes into contact with hot com- ponents in the engine compartment, it may
ignite. There is a risk of fire and injury.
Let the engine cool down before you add anti-
freeze. Make sure that antifreeze is not spilled
next to the filler neck. Thoroughly clean the
antifreeze from components before starting
the engine.
!Only add coolant that has been premixed
with the desired antifreeze protection. You
could otherwise damage the engine.
Further information on coolants can be found
in the Mercedes-Benz Specifications for Ser-
vice Products, MB BeVo 310.1, e.g. on the
Internet at http://bevo.mercedes-benz.com.
Or contact a qualified specialist workshop.
!Always use a suitable coolant mixture, even
in countries where high temperatures prevail.
Otherwise, the engine cooling system is not
sufficiently protected from corrosion and
overheating.
iHave the coolant regularly replaced at a
qualified specialist workshop and the replace-
ment confirmed in the Maintenance Booklet.
Comply with the important safety notes for ser-
vice products when handling coolant
(
Ypage 281).
The coolant is a mixture of water and anti-
freeze/corrosion inhibitor. It performs the fol-
lowing tasks:
RAnti-corrosion protection
RAntifreeze protection
RRaising the boiling point
If the coolant has antifreeze protection down to
-35 ‡ (-37 †), the boiling point of the coolant
during operation is approximately 266 ‡
(130 †).
284Service products and filling capacities
Technical data
Page 287 of 290
The antifreeze concentrate/corrosion inhibitor
concentration in the engine cooling system
should:
Rbe at least 50%. This will protect the engine
cooling system against freezing down to
approximately -35 ‡ (-37 †).
Rnot exceed 55% (antifreeze protection down
to -49‡[-45 †]). Otherwise, heat will not be
dissipated as effectively.
Mercedes-Benz recommends an antifreeze/
corrosion inhibitor concentrate in accordance
with MB Specifications for Service Products
310.1.
The coolant is checked with every maintenance
interval at a qualified specialist workshop.
iWhen the vehicle is first delivered, it is filled
with a coolant mixture that ensures adequate
antifreeze and anti-corrosion protection.
iThe coolant is checked with every mainte-
nance interval at a qualified specialist work-
shop.
Filling capacities
ModelCapacity
All models15.0 US qt (14.2 l)
Windshield washer system
Important safety notes
GWARNING
Windshield washer concentrate could ignite if it comes into contact with hot engine compo-
nents or the exhaust system. There is a risk of
fire and injury.
Make sure that no windshield washer con-
centrate is spilled next to the filler neck.
!Only use washer fluid that is suitable for
plastic lamp lenses, e.g. MB SummerFit or MB WinterFit. Unsuitable washer fluid could dam-
age the plastic lenses of the headlamps.
!Only MB SummerFit and MB WinterFit
washer fluid should be mixed together. The
spray nozzles may otherwise become
blocked. Do not use distilled or de-ionized water, other-
wise, the level sensor may give a false reading.
At temperatures above freezing:
XFill the washer fluid reservoir with a mixture of
water and windshield washer fluid, e.g. MB
SummerFit.
Add 1 part MB SummerFit to 100 parts water.
At temperatures below freezing:
XFill the washer fluid reservoir with a mixture of
water and washer fluid, e.g. MB WinterFit.
For the correct mixing ratio refer to the infor-
mation on the antifreeze reservoir.
iAdd windshield washer fluid, e.g. MB Sum-
merFit or MB WinterFit, to the washer fluid all
year round.
Climate control system refrigerant
Important safety notes
The climate control system of your vehicle is fil-
led with refrigerant R ‑134a.
The instruction label regarding the refrigerant
type used can be found on the radiator cross
member.
!Only the refrigerant R ‑134a and the PAG oil
approved by Mercedes-Benz may be used.
The approved PAG oil may not be mixed with
any other PAG oil that is not approved for
R-134a refrigerant. Otherwise, the climate
control system may be damaged.
Service work, such as refilling with refrigerant or
replacing component parts, may only be carried
out by a qualified specialist workshop. All appli-
cable regulations must be adhered to, SAE
standard J639 included.
Always have work on the climate control system carried out at a qualified specialist workshop.
Service products and filling capacities285
Technical data
Z
Page 288 of 290
Refrigerant instruction label
Example: refrigerant instruction label
:
Warning symbol
;Refrigerant filling capacity
=Applicable standards
?PAG oil part number
AType of refrigerant
Warning symbol :advises you about:
RPossible dangers
RHaving service work carried out at a qualified
specialist workshop
Filling capacities
All modelsCapacity
Refrigerant22.9 ± 0.4 oz
(650 ± 10 g)
PAG oil4.2 oz
(120 g)
Vehicle data
General notes
Please note that for the specified vehicle data:
Rthe heights specified may vary as a result of:
-Tires
-Load
-Condition of the suspension
-Optional equipment
ROptional equipment reduces the maximum
payload.
Dimensions and weights
All models:Opening height
Rear wing retracted78.1 in (1985 mm)
Rear wing extended80.6 in (2047 mm)
Fixed rear wing83.4 in (2119 mm)
All models
Vehicle length179.5 in (4560 mm)
Vehicle width
including outside
mirrors81.7 in (2075 mm)
Vehicle height50.7 in (1288 mm)
Wheelbase103.5 in (2630 mm)
Turning radius37.7 ft (11.50 m)
Maximum trunk
load220 lb (100 kg)
286Vehicle data
Technical data