battery MERCEDES-BENZ B-CLASS HATCHBACK 2021 Owner's Manual

Syst
Syst
em limits
em limits
ECO Assist can function even more precisely if
th ero ute is adhered towhen route guidance is
active. The basic function is also available without
active route guidance. Not all information and
tra1c situations can be fore seen. The quality
depends on the map data.
ECO Assist is only an aid. The driver is responsible
fo rke eping a safe distance from theve hicle in
front, forve hicle speed and for braking in good
time. The driver must be ready tobrake at all
times ir respecti veof whe ther the system inter-
ve nes.
The system may be impai red or may not function
in thefo llowing situations:
R If visibility is poor, e.g. due toinsu1cient illu-
mination of thero ad, highly variable shade
conditions, rain, sno w,fog or heavy spr ay.
R Ifth ere is glare, e.g. from oncoming tra1c,
direct sunlight or re0ections.
R Ifth ere is dirt on the windscreen in the area of
th e multifunction camera or the camera is
misted up, damaged or obscured. R
Ifro ad signs are hard todetect, e.g. due to
dirt, snow or insu1cient lighting, or because
th ey are obscured.
R Ifth e information on the navigation system's
digital map is incor rect, insu1cient or out of
date.
R If signs are ambiguous, e.g. road signs in road-
wo rks or in adjacent lanes. F F
unction of t
unction of t he r
he rout
oute-based oper
e-based oper ating-mode s
ating-mode strtrat-
at-
egy (plug-in h
egy (plug-in h ybr
ybrid)
id) %
The following function is countr y-dependent
and available only in conjunction with an inte-
gr ated navigation system.
The route-based operating-mode strategy is active
only in drive prog rams A and;. When
ro ute guidance is active, data on the planned
ro ute is anal ysed. This function can be activated
and deactivated in the multimedia system
(/ page 301).
If th e function is active, data on the fur ther course
of thero ute is evaluated. This includes, e.g. road
type, speed limi tations and altitude data. The
hybrid system then adapts the operating
strategy tothe fur ther course of thero ute:
R Use of electrical energy and the combustion
engine are adap ted.
R State of charge ofthe high-voltage battery is
controlled accordingl y.
R Electrical energy is reser ved especially for
electric mode, e.g. urban route sections.
R The vehicle automatically selects the operat-
ing mode.
When thero ute-based operating-mode strategy is
activated, the energy 0ow display sho ws the sta-
tus of the function as – active or passive
(/ page 302).
The route-based operating-mode strategy is
switched topassive under thefo llowing condi-
tions:
R You are driving in a drive prog ram other than
A or;.
R Route guidance is active.
R High-voltage battery's state of charge istoo
lo w. Driving and parking
181
181

D
D
YN
YNAMIC SELECT switch AMIC SELECT switch F
F
unction of t
unction of t he D
he DYN
YNAMIC SELECT switchAMIC SELECT switch %
Depending on the engine and equipment, the
ve hicle has di.erent drive prog rams.
Use theDY NAMIC SELECT switch tochange
between thefo llowing drive prog rams.
The drive prog ram selected appears in the inst ru-
ment displa y.
= Individual
R Individual settings
C Sport
R Continues too.er stability but with a sporty
setup
R Allo ws th e sporty driver a more active driving
style
R Driving with the combustion engine and rein-
fo rc ed boost e.ect (plug-in hybrid)
R Deactivation of the combustion engine when
stationary (plug-in hybrid)
R Only suitable for good road conditions, a dry
ro ad sur face and a clear st retch of road A
Comfort
R Comfor table and economical driving
R Balance between traction and stability
R The selection of the matching drive type by
th ehy brid system depends on the driving con-
ditions and the distance (plug-in hybrid)
R Recommended for all road conditions
Î Electric (plug-inhybrid)
R Electric mode – driving without the combus-
tion engine is possible up toappr ox.
140 km/h
R Adjustable recuperation in overrun mode
R Adaptation of Active Distance Assist
DISTRONIC for electric mode
R Depending on the equipment, the maximum
set speed for cruise control, limiter and Active
Distance Assist DISTRONIC can be limited to
th e maximum electrically drivable speed
R Activation of the combustion engine via the
pressure point of the accelerator pedal (kic k-
down) Ï
Battery Level (plug-inhybrid)
R Prioritised maintenance of the state of charge
of the high-voltage batter y,e.g. for subse-
qu ent journe ysinthe inner city/low emission
zones
R The selection of the matching drive type by
th ehy brid system depends on the driving con-
ditions and the distance
; Eco
R Only available forve hicles with automatic
transmission
R Particular lyeconomical driving
R Balance between traction and stability
R Recommended for all road conditions
R Full de velopment of all intelligent hybrid func-
tions and adap tation of the coasting charac-
te ristics of theve hicle totra1c (plug-in hybrid)
R The selection of the matching drive type by
th ehy brid system depends on the driving con-
ditions and the distance (plug-in hybrid) 182
182
Driving and parking

Char
Char
ging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery (plug-in
y (plug-in
h
h ybr
ybr id)
id) N
No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt ery
ery *
N
NOOTE
TE High-voltage battery damage due to
leaving theve hicle idle for lengt hyperiods
of time Lithium-ion batteries
experience a natural self-
dischar ge.
Exhausti vedischarging can therefore occur if
th eve hicle is idle for se veral months. This can
damage the high-voltage batter y.#
Toavo id damage, please obser vethefo l-
lowing recommendations when handling
th e high-voltage batter y.*
N
NO
OTE
TE Accelerated ageing of the high-volt-
age battery As a
result of its basic characteristics, the
storage capacity of and the amount of energy
av ailable from the high-voltage battery
decrease over the course of its life. Due to th
is, bo th the maximum electrical range that
can be achie vedby theve hicle and its maxi-
mum elect rical output can be impaired.
The following factors could accelerate the age-
ing of the high-voltage batter y:
R a high le vel of charge , especially if the
ve hicle is idle for a lengt hyperiod of time
R frequent rapid charging with direct cur rent
(mode 4)
R leaving theve hicle idle for lengt hyperiods
at high ambient temp eratures #
Toavo id accelerated ageing, please
obser vethefo llowing recommendations
when handling the high-voltage batter y. Re
commendations when handling the high-voltage
batter y:
R Only charge the high-voltage battery with
direct cur rent (mode 4) if necessar y.
R If leaving theve hicle idle for lengt hyperiods,
park up theve hicle with a high- voltage battery
ch arge leve l between 25% and 30%. Do not ke
ep the high-voltage battery continuously
connected topowe r supply equipment.
R If leaving theve hicle idle for lengt hyperiods of
time avoid, if possible, high ambient temp era-
tures.
R Check the high-voltage battery's charge level
ev ery six weeks (/ page 214).
R Char gethe high-voltage battery if thech arge
le ve l is below 15%.
R Do not disconnect the 12 V battery even if the
ve hicle is leT idle for a lengt hyperiod. Other-
wise, the condition of theve hicle's high- volt-
age battery cannot be monitored.
Depending on the equipment and national ver-
sion, your vehicle is equipped with one of thefo l-
lowing vehicle soc kets:
R Type 1 forch arging with alternating cur rent
(mode 2/3)
R Type Combo 1 forch arging with alternating
cur rent (mode 2/3) and charging with direct
cur rent (mode 4)
R Type 2 forch arging with alternating cur rent
(mode 2/3) 198
198
Driving and parking

R
Type Combo 2 forch arging with alternating
cur rent (mode 2/3) and charging with direct
cur rent (mode 4) Combo 1
vehicle soc ket Combo 2
vehicle soc ket
1 Type 1 or type 2 connection forch arging with
alternating cur rent
2 Socketex tension forch arging with direct cur-
re nt
% When using a CCS (Combined Cha rging Sys-
te m) charging cable tocharge with direct cur-
re nt at a combo vehicle soc ket, bo thvehicle soc
ket connections 1and 2are used for
ch arging.
Charging options forth e high-voltage battery
(mode 2, 3 or 4):
R Charging through recuperation while theve hi-
cle is in motion
R Charging with alternating cur rent when sta-
tiona ry:
- at a mains soc ket (mode 2)
- at a wallbox or charging station (mode 3)
R Charging with direct cur rent when stationary
(vehicles with combo vehicle soc kets):
- at a fast charging station (mode 4)
Depending on the count ry-speci/c vehicle equip-
ment and your vehicle's charging cable, single
phase ACcharging is also possible.
Obser vethe di.erent grid requ irements of your
cur rent location when charging. Only use charging
cables which conform tothegr id requi rements.
Consult a quali/ed elect rician or your local grid
operator if you ha veany questions. Driving and parking
199
199

It is
recommended that youch arge the high-volt-
age battery at a wallbox or charging station due to
th e impr ovedch arging per form ance and better
ch arging e1ciency o.ered.
S
S t
to
o wing t
wing t he c
he char
harging cable
ging cable
Alw ays st owtheve hicle charging cable in the
ch arging cable bag pr ovided and secure it in the
boot or load compartment of your vehicle.
Otherwise, thech arging cable is not su1ciently
secured.
Syst
Syst em limits em limits
The po wer output of the high-voltage battery may
be impaired bythefo llowing:
R High or low outside temp eratures
R Electrical auxiliary consumers in theve hicle
being switched on, e.g. operating the air con-
ditioning system
R Extended periods without charging
The charging time of the high-voltage battery may
be increased bythefo llowing:
R High or low outside temp eratures
R Extended periods without charging R
The maximum available charge cur rent of the
ch arging facility
R The charging cur rent set (mode 2) in the multi-
media system (/ page 301) N
No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery at t
y at t he
he
mains soc ke
mains soc ket (mode 2)
t (mode 2) &
D
DAN
AN GER
GER Risk of fatal injury from incor-
re ctly ins talled component parts
Connecting thech arging cable toa mains
soc ket using incor rectly ins talled component
parts could cause a /re or an electric shoc k,
fo rex ample. #
Only connect thech arging cable to a
mains soc ketth at:
R Has been proper lyinstalled and
R Has been inspected byaqu ali/ed elect ri-
cian #
For saf etyre asons, only use thech arging
cable supplied with theve hicle or an
original Mercedes-Benz charging cable. #
Purchase these parts at a Mercedes-
Benz Service Centre and obtain advice
th ere.
Mercedes-Benz thoroughly tests these original
ch arging cables forth eir suitability for high-
vo ltage charging of your vehicle. #
Never use a damaged charging cable. #
Do not use:
R Extension cables
R Extension reels
R Multiple soc kets #
Never use soc ket ada pters toconnect
th ech arging cable tothe mains soc ket.
The only exception being if the adap ter
has been tested and appro vedby the
manufacturer forch arging the high-volt-
age battery of an electric vehicle. #
Obser vethe saf ety no tes in the operat-
ing inst ructions forth e soc ket ada pter. Only
thefo llowing charging cables may be used:
R The charging cable supplied with theve hicle. 200 200
Driving and parking

R
Ach arging cable that has been appr ovedfor
th eve hicle.
The charging process can vary depending on the
po we r supply equipment.
Shor terch arging times can be achie ved in thefo l-
lowing ways:
R Charging at a wallbox.
R Charging at a charging station.
When doing so, alw ays obser vethe local informa-
tion.
Do not lea vethech arging cable cont rols hanging
loose from a mains soc ket.
Do not liT the controls bythefo llowing compo-
nent parts:
R The charging cable connector.
R The mains plug.
When charging, pr otect thech arging cable cont rol
element from excessive heat such as direct sun-
light. Otherwise, thech arging process may be
cancelled. N No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery at a
y at a
w
w allbo
allbo x or c
x or c har
harging st
ging st ation (mode 3)
ation (mode 3) &
D
DAN
AN GER
GER Risk of fatal injury from incor-
re ctly ins talled component parts
Connecting thech arging cable toawa llbox
using incor rectly ins talled component parts
could cause a /re or an electric shoc k,for
ex ample. #
Only connect thech arging cable to a
wa llbox that:
R Has been proper lyinstalled and
R Has been inspected byaqu ali/ed elect ri-
cian #
For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer forch arg-
ing the high-voltage battery in an electric
ve hicle. #
Never use damaged charging cables. #
Do not extend thech arging cable. #
Do not use adap ters. #
Obser vethe saf ety no tes in the operat-
ing inst ructions forth ewa llbox. If
ch arging at a wallbox without pre-ins talled
cable, use the optionally available charging cable
fo rwa llbox and charging station (mode 3). The
ch arging cable is st owed in a bag in the boot/
luggage compartment.
Only use charging cables that ha vebeen tested
and appro vedby the manufacturer forch arging
th e high-voltage battery in an electric vehicle. &
D DAN
AN GER
GER Risk of fatal injuries due todam-
aged components
Connecting thech arging cable toach arging
station using a damaged component part
could cause a /re or an elect ric shoc k,for
ex ample. #
Forch arging stations with a preinstalled
ch arging cable:
R Perform a visual check of thech arg-
ing station for obvious faults, such as
massive damage tothe housing or
ch arging cable. Driving and parking
201 201

#
Forch arging stations without a preinstal-
led charging cable:
R For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer for
ch arging the high-voltage battery in
an electric vehicle.
R Never use damaged charging cables.
R Do not extend thech arging cable.
R Do not use adap ters. #
Make sure toobser vethe saf ety in form a-
tion on thech arging station. Most
charging stations must be activated before
th ech arging process, e.g. using an RFID card.
Obser vethe on-site operator's inst ructions forthe
ch arging station.
The amount of ene rgy dispensed forth ech arging
process, shown bythech arging station, may be
higher than the amount of energy actually absor-
bed bythe high-voltage batter y.This is there sult
of di.erent le vels of charging losses and is descri-
bed as rech arge e1ciency. Charging losses occur,
fo rex ample, due toheat that builds up when ch
arging or from auxiliary consumers that are
switched on. Further information on rech arge e1-
ciency can be obtained at a quali/ed specialist
wo rkshop. N
No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery at a
y at a
f
f as
ast c t c har
har ging st
ging st ation (mode 4)
ation (mode 4) &
D
DAN
AN GER
GER Risk of fatal injuries due todam-
aged components
Connecting thech arging cable toach arging
station using a damaged component part
could cause a /re or an elect ric shoc k,for
ex ample. #
Forch arging stations with a preinstalled
ch arging cable:
R Perform a visual check of thech arg-
ing station for obvious faults, such as
massive damage tothe housing or
ch arging cable. #
Forch arging stations without a preinstal-
led charging cable:
R For saf etyre asons, only use charging
cables that ha vebeen tested and appro
vedby the manufacturer for
ch arging the high-voltage battery in
an electric vehicle.
R Never use damaged charging cables.
R Do not extend thech arging cable.
R Do not use adap ters. #
Make sure toobser vethe saf ety in form a-
tion on thech arging station. Most
charging stations must be activated before
th ech arging process, e.g. using an RFID card.
Obser vethe on-site operator's inst ructions forthe
ch arging station.
The charging cable forth eve hicle must not be
lon gerth an 30 m due tothe legal requ irements in
some countries. This is toprev ent the inter fer-
ence of signals being received byradio communi-
cation devices in theve hicle or in close pr oximity
to thech arging station. Be awarethat parts of the
ch arging cable may be routed under ground. If in
doubt, ask thech arging station operator if this is
th e case before charging the high-voltage batter y.
The amount of energy dispensed forth ech arging
process, shown bythech arging station, may be 202
202
Driving and parking

The
003D indicator lamp 4and status dis-
play 30ash orange and, as soon as the high-
vo ltage battery is charge d, green.
When thech arging cable is connected totheve hi-
cle, theve hicle cann otbe star ted or mo ved.
At the start of thech arging process, thech arge
le ve l display is shown in the Instrument Display
with a charging prediction. The charging predic-
tion either refers to the predicted charge leve l at
th e set departure time, or the time at which the
high- voltage battery will be fully charge d.
% Depending on thete mp erature, thefa n and
bat tery cooling system may audibly switch on
during thech arging process.
% Ifth eve hicle is idle for lengt hyperiods and
connected tothe mains suppl y,the high-volt-
age battery will be rech arge d automatically as
needed or when electrical consumers are
activated (e.g. the pre-entry climate control).
% The vehicle is equipped with an elect rical fuse
which pr otects it against overvoltage in the
mains suppl y.This electrical fuse may trip dur-
ing se vere thunderstorms, forex ample, and
may cause the fuse in the building totrip or may inter
rupt thech arging process. These
functions pr otect theve hicle.
ATer the fuse in the building is switched on
again, thech arging process resumes automat-
icall y.Fo llowing an inter ruption in the po wer
supply without the fuse in the building being
tripped, it may take up to te n minutes for
ch arging toresume automaticall y. Ending t
Ending t
he alt
he alter
ernating curr
nating curr ent c
ent char
harging pr
ging pr ocess
ocess
(mode 2/3)
(mode 2/3) R
R
eq
eq uir
uir ements:
ements:
R The dis tance between theke y and theve hicle
does not exceed 1 m. Combo 1 v
Combo 1 v ehicle socket
ehicle soc ket #
Press charging inter ruption button 3.
or #
Unlock theve hicle.
The charging process is ended. The 0036indi-
cator lamp 1lights up white. The vehicle
soc ket is unloc ked. Driving and parking
209
209

%
When theve hicle is switched on (the õ
displ ayis lit in the Instrument Display), soc ket
0ap 1cannot be opened. #
Press cat ch7 tothe leT and fold open
soc ket co ver5.
% The CCS charging cable connector requ ires
connections 6and 8. Therefore, it is nec-
essary toopen bo thparts of soc ket co ver5. #
Insert the CCS charging cable connector into
th eve hicle soc ketto the stop.
Make sure that thech arging cable is not taut
when inser ted.
The 003D indicator lamp 4and status dis-
play 30ash orange and, as soon as the high-
vo ltage battery is charge d, green.
When thech arging cable is connected totheve hi-
cle, theve hicle cann otbe star ted or mo ved.
At the start of thech arging process, thech arge
le ve l display is shown in the Instrument Display
with a charging prediction. The charging predic-
tion either refers to the predicted charge leve l at
th e set departure time, or the time at which the
high- voltage battery will be fully charge d. %
Depending on thete mp erature, thefa n and
bat tery cooling system may audibly switch on
during thech arging process.
% Ifth eve hicle is idle for lengt hyperiods and
connected tothe mains suppl y,the high-volt-
age battery will be rech arge d automatically as
needed or when electrical consumers are
activated (e.g. the pre-entry climate control). Ending t Ending t
he dir
he direct curr
ect curr ent c
ent c har
harging pr
ging pr ocess (mode
ocess (mode
4)
4) R
R
eq
eq uir
uir ements:
ements:
R The distance between theke y and theve hicle
does not exceed 1 m. Combo 1 v
Combo 1 v ehicle socket
ehicle soc ket #
Press charging inter ruption button 3.
The charging process is ended. The 0036indi-
cator lamp 1lights up white. The vehicle
soc ket is unloc ked. #
Press and hold button 2onthech arging
cable connector and remo vethech arging
cable connector from theve hicle soc ket. Driving and parking
213
213

R
the electric parking brake is not applied N
No
ot
tes on par
es on par king up t
king up the v
he vehicle
ehicle If
yo u lea vetheve hicle par ked up for longer than
six weeks, it may su.er damage thro ugh disuse.
The 12 V battery may also be impaired or dam-
aged byheavy discharging.
V
V ehicles wit ehicles wit h aut
h automatic tr
omatic tr ansmission:
ansmission: do not dis-
connect the 12 V battery even if theve hicle is leT
idle for a lengt hyperiod.
% Further information can be obtained at a
qu ali/ed specialist workshop. S
S
t
tandb
andb y mode (e
y mode (e xt
xtension of t
ension of t he st
he start
arter batt
er batt er
ery's
y's
per
per iod out of use)
iod out of use) S
S
t
tandb
andb y mode function
y mode function
% This function is not available for all models.
If standby mode is activated, energy loss will be
minimised during extended periods of non-opera-
tion. St
andby mode is characterised bythefo llowing:
R The star ter battery is preser ved.
R The maximum non-operational time appears in
the media displa y.
R The connection toonline services is inter rup-
te d.
R The ATA (anti-theT alarm system) is not availa-
ble.
R The interior pr otection and tow- aw ay protec-
tion functions are not available.
R The function for de tecting collisions on a
par kedve hicle is not available.
If th efo llowing conditions are ful/lled, standby
mode can be activated or deactivated using the
multimedia system:
R The vehicle is switched on.
R The vehicle has not been star ted.
Exceeding theve hicle's displ ayed non-operational
time may cause incon venience; i.e. it cannot be
guaranteed that the star ter battery will reliably
start theve hicle. Char
gethe star ter battery in thefo llowing situa-
tions:
R The vehicle's non-ope rational time must be
ex tended.
R The Battery charge insufficient for standby
mode messa geappears in the media displa y.
% Standby mode is automatically deactivated
when theve hicle is switched on.
A
A ctiv ctiv ating/deactiv
ating/deactiv ating st
ating standb
andby mode (par
y mode (par king up
king up
t
t he v
he v ehicle)
ehicle)
R
R eq
eq uir
uir ements:
ements:
R The engine is switched o..
Multimedia system: 4 © 5
Settings 5
Vehicle #
Activate or deactivate Standby mode. #
Select Yes. 222
222
Driving and parking