height adjustment MERCEDES-BENZ C-Class 2000 W202 Owner's Manual

Seats, Front

Warning !
Do not adjust the driver's seat while driving. Adjusting the seat while driving could cause the driver to lose
control of the vehicle. Never ride in a moving vehicle with the seat back reclined. Sitting in an excessively
reclined position can be dangerous.
You could slide under the seat belt in a collision. If you slide under it, the belt would apply force at the
abdomen or neck. That could cause serious or even fatal injuries. The seat backrest and seat belt provide
the best restraint when the wearer is in an upright position and the belt is property positioned on the body.
Never place hands under seat or near any moving parts while a seat is being adjusted

1 - Seat, up/down
2 - Seat, fore7aft
3 - Seat cushion tilt
4 - Backrest tilt
5 - Head restraint

Adjust head restraint to support the back of the head approximately at ear level.
The head restraint angle can also be adjusted manually.
Note:
Your car is equipped with power head restraints, do not try to raise or lower them manually.


Power Seat (Optional on model C230 Kompressor passenger side)
The slide switches are located in each front door. Turn electronic key in steering lock to position 1 or 2 (with a front
door open, the power seats can also be operated with the electronic key removed or in steering lock position 0).

Warning !
When leaving the vehicle always remove the electronic key from the steering lock. The power seats can also
be operated with the driver's or passenger door open. Do not leave children unattended in the vehicle or with
access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause serious personal injury.

Caution !
Do not remove head restraints except when mounting seat covers. For removal refer to Head Restraints, Front, see
Index. Whenever restraints have been removed be sure to reinstall them
before driving.

Important !
Prior to operating the vehicle, the driver should adjust the seat height for proper vision as well as fore/aft placement
and seat back angle to insure adequate control, reach, operation, and comfort. The head restraint should also be
adjusted for proper height. See also airbag section for proper seat positioning. In addition, also adjust the steering
wheel to ensure
adequate control, reach, operation, and comfort, if vehicle so equipped. Both the inside and outside rear view mirrors
should be adjusted for adequate rearward vision. Fasten seat belts. Infants and small children should be seated in a
properly secured restraint system that complies with U.S. Federal Motor Vehicle Safety Standard 213 and Canadian
Motor Vehicle Safety Standard 213. All seat, head restraint, steering wheel, and rear view mirror adjustments as well
as fastening of seat belts should be done before the vehicle is put into motion.

Warning !
Children 12 years old and under must never ride in the front seat, except in a Mercedes-Benz authorized
BabySmart™ compatible child seat, which operates with the BabySmart™ system installed in the vehicle to
deactivate the passenger side airbag when it is properly installed. Otherwise they will be struck by the airbag
when it inflates in a crash. If this happens, serious or fatal injury will result. The back seat is the safest place
for children. Infants and small children must ride in the back seats and be seated in an appropriate infant or
child restraint system, which is properly secured with the vehicle's seat belt, fully in accordance with the seat
manufacturer's instructions. A child's risk of serious or fatal injuries is significantly increased if the child
restraints are not properly secured in the vehicle and the child is not properly secured in the child restraint.

Manual Seat

(Standard equipment on Model C 230 Kompressor passenger side)
We recommend to adjust the seat in the following order:
1. Seat height adjustment
2. Fore/aft adjustment
3. Seat cushion tilt
4. Backrest tilt
5. Head restraint inclination
6. Head restraint height

Fore/aft Adjustment
Lift handle (2), slide seat to desired position and allow handle to reengage.
Check for proper engagement before driving.

Seat Height Adjustment
Raise or lower lever (1). The seat will be raised or lowered one notch at a time.
Allow lever to re-engage. Check for proper engagement before driving.


Seat Cushion Tilt
Turn handwheel (3) forward or backward.


Backrest Tilt
Turn handwheel (4).

Head Restraint Height
Raising:
Pull up on head restraint.
Lowering:
Push button (6) and push down on head restraint.
Adjust head restraint to support the back of the head approximately at ear level.
The head restraint inclination can also be adjusted manually (5).

Caution !
Do not remove head restraints except when mounting seat covers. For removal refer to Head
Restraints in Index. Whenever restraints have been removed be sure to reinstall them before driving.

Multicontour Seat (optional)

We recommend to adjust the multicontour seat in the following order:
1. Seat cushion depth
2. Backrest bottom
3. Backrest center
4. Side bolster adjustment

Some models may be equipped with multicontour seats. These seats have movable seat cushions,
and inflatable air cushions built into the backrest to provide additional lumbar and side support.
The seat cushion movement and amount of backrest cushion height and curvature can be
continuously varied with regulators (1, 2 and 3) after turning the electronic key in steering lock to
position 2.

The side bolsters of the backrest can be adjusted with rocker switch (4):
• press down forward end-increase side support,
• press down rearward end-decrease side support.

If the engine is turned off, the last cushion setting is retained in memory, and automatically adjusts
the cushion to this setting when the engine is restarted.

Armrest (Rear Bench Seat)

Pull down the armrest. For removal of rear seat cushion, see Index.

Cup Holder in Rear Bench Armrest

Briefly press drawer and pull out to its detent.

Caution !
Keep cup holder closed while travelling. Place only containers
that fit into the cup holder to prevent spills.
Do not fill containers to a height where the contents could spill
during vehicle maneuvers, especially hot liquids.


Adjusting Telescoping Steering Column (optional)


Warning!
Do not adjust the steering wheel while driving. The telescoping
adjustment must be locked while driving. Adjusting the steering
wheel while driving, or driving without the telescoping adjustment
locked could cause the driver to lose control of the vehicle.


Unlocking:
Pull handle (1) out to its stop. The indicator lamp, located in the instrument cluster, comes on.
Adjusting:
To lengthen or shorten the steering column, pull out or push in steering wheel.
Locking:
Push handle (1) in until it engages. The indicator lamp, located in the instrument cluster, goes out.

Important!
With the electronic key in steering lock position 2, an indicator lamp in the instrument cluster comes on. It should go
out when the engine is running. If the indicator lamp does not go out after starting the engine, the adjustable steering
column is not locked properly. Do not drive the vehicle until you have properly locked the steering column.

Fastening of Seat Belts

1. Latch plate
2. Buckle
3. Release button



Push latch plate (1) into buckle (2) until it clicks. Do not twist the belt. A twisted seat belt may cause injury.
The lap belt should be positioned as low as possible on your hips and not across the abdomen.
Tighten the lap portion to a snug fit by pulling shoulder portion up. The shoulder portion of the seat belt must
be pulled snug and checked for snugness immediately after engaging it.
Adjust seat belt so that shoulder portion is located as close as possible to the middle of your shoulder (it should
not touch the neck). For this purpose, you can adjust the height of the belt outlet.
Three positions are available





4. Button for belt outlet eight adjustment


To raise, slide belt outlet upward. To lower, press button (4) and slide belt outlet downward.

Caution !
For safety reasons, avoid adjusting the seat or seat back into positions which could affect the correct seat
belt position.


Lap Belt for Center Seating Position of the Rear Seat
Pull belt with latch plate (1) over lap so that the belt is positioned as low as possible on your hips and not
across the abdomen. Push latch plate (1) into buckle (2) until it clicks. Do not twist the belt but keep it tight.
To tighten the belt: With the latch plate engaged, pull the loose end of the belt.
To lengthen the belt: With the belt unfastened, turn the latch plate so that it is a little more than 90°
perpendicular to the belt, then extend the belt. Fasten the belt and tighten as stated above.
To disengage the belt, push red button (3) in the buckle.
If the center seat is not occupied, the belt buckle and rolled-up seat belt can be stored in the space
next to the rear armrest (to the left or right of armrest).
Note:
For cleaning and care of the seat belts, see Cleaning and Care of the Vehicle in Index.



Unfastening of Seat Belts
Push the release button (3) in the belt buckle (2). Allow the retractor
to completely rewind the seat belt by guiding the latch plate (1).
Operation:
The inertia reel stops the belt from unwinding during sudden vehicle
stops or when quickly pulling on the belt.
The locking function of the reel may be checked by quickly pulling
out the belt.

Adjusting Headlamp Aim
(Xenon)





Correct headlamp adjustment is
extremely important. To check and
readjust a headlamp, follow steps 1
through 5. Please note:
• Low beam adjustments
simultaneously aim the high
beam and fog lamp.
• Vehicle should have a normal
trunk load.
• Vertical aim adjustments
change horizontal aim.


1. Park vehicle on level surface approximately 25 ft. (7.6 m) from a vertical
test screen or wall. The centerline of the vehicle must be at a 90° angle
to the test screen.
2. (Low beams on):
Using a carpenter's level, align and mark a vertical centerline
(8) on the test screen using the vertex of the angle formed in
each beam image. As a check, the distance between center-
lines should be 47 1/4 inches (1198 mm). If the distance does not check,
have the system verified at an authorized Mercedes-Benz dealer.
3. (Low beams off):
Measure the vertical height from the floor to reference point (10)
on low beam lens. Subtract approx. 2 inches (53 mm) from
measurement, and mark a horizontal centerline (9) on the
test screen at the resulting height from the floor. It must be
at a 90° angle to the vertical centerline.
4. Open hood.





5. Vertical headlamp aim (low beams on):
Simultaneously turn adjusting screws (1 and 2) equally in the
same direction (counterclockwise to adjust headlamp downward,
clockwise upward) until the headlamp (low beam)
illuminates the test screen as shown.
The left and right headlamps must be adjusted individually.
Note:
If it is not possible to obtain a proper headlamp adjustment, have
the system checked at your authorized Mercedes-Benz dealer.