Air MERCEDES-BENZ C-Class 2008 W204 Comand Manual

137 Navigation
Destination input
Destination memory list without
predictive speller
To select a destination: Rotate ymz
or slide qmr.
To cancel selection: Press the í
button.
or
Select “Back” and press n.
To confirm selection: Press n.
To start route calculation: Select
“Start”, see also (
page 135).
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Destination” K “From Last
Destinations”.
1Last destination
To select a destination: Rotate ymz
or slide qmr.
To confirm selection: Press n.
To start route calculation: Select
“Start”, see also (
page 135).
i For more information on the “Last destina-
tions” memory go to (
page 162).
i In some countries, entering destinations via
the map is not possible at vehicle speeds above
apprx. 3 mph. The function becomes available
again as soon as the speed falls below apprx.
2mph.
Using the destination entry via the map, you can
also enter a destination that lies within the digital
map but whose address data is not included in
the digital map.
Opening the map
If at least a city has been entered, se-
lect “Map” in the Enter Destination
menu (
page 126).
or
If necessary display the menu system
in the map display (
page 119).
Select “Destination” K “Using Map”.
In both cases, the map together with
crosshairs appears.
Entering destination from the last
destinationsEntering destination via the map

138 Navigation
Destination input
1Current vehicle location (displayed if
the vehicle location is close to the
crosshairs position)
2Crosshairs
3Information on crosshairs position
4Set map scale
i The display 3 depends on the setting se-
lected in “Information On Map” (
page 123). It
may display the current road if corresponding
data is available in the digital map. Or it displays
the geo-coordinate position of the crosshairs if
“Geo-coordinates display” is activated
(
page 124) and if there is adequate GPS re-
ception.
Moving the map and selecting a desti-
nation
To move the map: Slide qmr, omp or
wmx.
To set the map scale: Rotate ymz.
Rotating clockwise makes the map
smaller, rotating counterclockwise en-
larges it.
To select a destination: Press n.
If the crosshairs are outside the digital
map, a route to this destination cannot
be calculated and the message “The
crosshair is off the map” is displayed.
Select “OK”.
If the destination is within the digital
map, COMAND tries to find the desti-
nation on the map.
If the destination can be found, the En-
ter Destination menu is displayed with
the address of the destination. Other-
wise you will see the entry “Destination
From Map”.
To start route calculation: Select
“Start”, see also (
page 135).
i If route guidance is active, you can enter a
stopover destination. Stopover destinations may
be predefined destinations in the following cate-
gories suggested by COMAND for you to select:

“Mercedes-Benz Service”

“Hospital”

“Gas Station”

“Parking Lot”

“Restaurant”
However, you can also enter destinations other
than those that have been predefined. Select the
menu item “OTHER” for this purpose.
You can influence the route guidance to the main
destination in a specific way using the stopover
function. Once the stopover destination has
been reached, COMAND automatically recalcu-
lates the route to the main destination.
Entering predefined destinations
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Destination” K “Stopover”.
Entering stopover destination

145 Navigation
POI input
i If “ALL TYPES” is selected in the list, the POI
list contains all the POIs in all subcategories of
the “RESTAURANT” main category that are locat-
ed in the search radius. The list item “OTHER” at
the end of the list contains all the POIs not as-
signed to any subcategory in the “RESTAURANT”
main category that are located in the search ra-
dius.
The selected main category contains no
subcategories:
Selecting it immediately opens the POI list.
The POI list then contains the available
POIs for the main category that are located
in the search radius.
POI list
As an example, the illustration below
shows the POI list for the main category of
“RESTAURANT”, “BREWPUB” subcategory
in the vicinity of the location.1Direction of destination
2Air-line distance to the destination
3Point of interest
4Selected category or subcategoryi The display 1 only appears if you have en-
tered a POI search in the vicinity of the current
position.
The display
2 is not displayed if you have en-
tered a POI within a particular city and have only
entered the state/province and the city.
Depending on the POI category selected,
COMAND uses different reference points when
determining the distance to the destination:

In the vicinity of the location: The distance to
the POI from the current vehicle location.

Local area of destination: The distance to
the POI from the destination entered.
Selecting a POI
Select the desired POI.
The full address of the selected POI is
displayed.
i If the selected POI has a telephone book en-
try, you can make a call to the POI.
1POI with address
2Initiates a call, if available
3Starts route calculation
4Cancels selection
To cancel selection: Press the í
button.
or
Select “Back”.
The POI list appears.


147 Navigation
POI input
i If the crosshairs are visible on the map, you
can enter POIs in the vicinity of the crosshairs.
If the crosshairs are not visible, you can enter
POIs in the vicinity of the current vehicle loca-
tion.
In the map display with the menu sys-
tem displayed (
page 119) select
“Guide”.
POIs are available:
Depending on the map scale selected,
POI symbols are displayed on the map.
The scale starting at which symbols are
displayed on the map varies from sym-
bol to symbol.
You can select which symbols
COMAND should display (
page 121).
The POI nearest to the center of the
screen is selected automatically.No POIs available:
A corresponding message is displayed.
i This message is also displayed if the menu
item “No Symbols” under “Map Display” has
been selected (
page 121).
To confirm message: Press n.
1Information about the highlighted POI
2Highlighted POI
To select a POI: Select “Next” or
“Previous”.
To display details on the selection:
Select “Details”.
To start route calculation: Select
“Start”, see also (
page 135).
You will be asked whether the POI
should be adopted as the destination.
Select “Yes” or “No”.
Route calculation starts if “Yes” is se-
lected; a new POI can be chosen if “No”
is selected.
Entering a POI via the map

162 Navigation
Last destinations
i COMAND automatically saves the last desti-
nations used for the last route calculation. If the
memory is full, COMAND deletes the oldest des-
tination. You can also save a destination from
the last destinations to the destination memory.
Here it is saved permanently.
Proceed as described in the “Accepting
from the last destinations” section
(
page 159).
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Position” K “Save Vehicle Posi-
tion”.
COMAND saves the current vehicle lo-
cation as a destination in the last desti-
nations memory.
i If you move the map manually, crosshairs
will appear on it. The crosshairs position can be
saved as a destination in the last destinations
memory.
To display menu system if applica-
ble: Press n.
Select “Position” K “Save Crosshair
Position”.
or during route guidance
To display menu system if applica-
ble: Press n.
Select “Position” K “Destination Posi-
tion Map”.
The map with the crosshairs position
on the destination appears.
To show the menu system: Press n.
Select “Position” K “Save Crosshair
Position”.
COMAND saves the crosshairs position
as a destination in the last destinations
memory.
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Destination” K “From Last
Destinations”.
The list of last destinations appears.
Select the desired destination.
Select “Options” K “Delete”.
Last destinations
Saving a destination permanently in
the destination memory
Saving vehicle location in the last
destinations
Saving crosshairs position in the last
destinationsDeleting one of the last destinations

172 System settings
Tele Aid*
The Tele Aid* system
(Tele Aid – Telematic Alarm Identification
on Demand)
The Tele Aid* system consists of three
types of response:
automatic and manual emergency
Roadside Assistance
Information
Automatically
An emergency call is initiated automatical-
ly following an accident in which the emer-
gency tensioning devices (ETDs) or air
bags deploy.
Initiating an emergency call manually
The SOS button is located in the overhead
control panel.

Briefly press SOS button cover to open.

Press SOS button (for longer than
2 seconds).
The indicator lamp in the SOS button
will flash until the emergency call is
concluded.

Wait for a voice connection to the Re-
sponse Center.

Close cover after the emergency call is
concluded.
i During the emergency call message “Emer-
gency Call Activated” is displayed, operation
from COMAND is not possible.
For a complete description and additional
information on Emergency calls please re-
fer to the vehicle Operator's Manual.
Tele Aid*Emergency calls

178 Voice Control
Overview
Canceling the dialog
Press the L button.
or
Say the command “Cancel” (except
when creating and storing voice tags,
navigation entries or during individual-
ization).
or
Press any button on COMAND.
Adjusting the volume
Start the dialog.
Give a command, e.g. “Help”.
Press the æ or ç button.
The volume increases or decreases
during voice output.
or
Set the volume for the voice output on
the volume control for COMAND.
Display messages
The audible help function can be supple-
mented by visual help on the display
(
page 167). If the help function is
switched on, the most important com-
mands that are currently possible appear
in the display when you start the dialog.
In the address book and navigation sys-
tem, a selection list is shown in the display
if voice control requires additional informa-
tion from you.
1Display
Entering numbers

Digits from “zero” to “nine” are permit-
ted.

Say the phone number in groups of
three to five digits.
Spell

The letters of the alphabet and the
numbers 0 - 9 are permitted.

Say the letters in groups of five to sev-
en letters.

Say each individual letter clearly.
i Using individualization, you can fine-tune
voice control to your own voice and thus improve
voice recognition. The process of individualiza-
tion is described in chapter “System Settings”
(
page 167).
i If you use individualization, it may impair
recognition of other users. Switch off individual-
ization if it makes recognition of other users
worse.

187 Voice Control
Navigation
Example of dialog:
sEnter Street
tPlease say the name of the street
sMabel’s Street
uThe system shows a numbered list
of street names on the display
tPlease select a line number.
sNumber three
tNumber three accepted
The street name is stored for route guid-
ance.
“Correction”
If you have entered or spelled a city or
street, you can use the “Correction” com-
mand to enter the city or street again or
spell it from the beginning.
“House number”
You can use the “House number” com-
mand to specify the house number for the
selected street in individual digits.Example of dialog:
sHouse number
tPlease say the house number in sin-
gle digits
sThree four
tThree four
sOkay
The house number is stored for route guid-
ance.
“Point of interest” (POI)
You can use the “Point of interest” com-
mand to select specific destinations (filling
stations, airports, stations, etc.).
Example of dialog:
sPoint of interest
uThe system shows the following list
in the display:
1 Current position
2 Other town
tPlease select a line number.
sLine number 1 ...
tLine number 1 accepted.uThe system shows a numbered list
of POI categories
tPlease select a line number or say
the category name
sLine number 5 ...
tNumber 5 accepted
uThe system shows a numbered list
with destinations from the selected
category
tPlease select a line number.
sLine number 1 ...
tLine number 1 accepted.
The specific destination which has the
number one is stored for route guidance.
i Depending on the selected area, other lists
may be shown.
You can only select points of interest in the
state or province the navigation system is
set for.