garage door opener MERCEDES-BENZ C-Class 2011 W204 Owner's Manual

Fuse box in the engine
compartment ................................. 267
Fuse box in the trunk .....................268
Notes ............................................. 266
G
Garage door opener Clearing the memory .....................235
Notes ............................................. 232
Opening/closing the garage door ..234
Programming the remote control ...232
Gear indicator (on-board
computer) .......................................... 171
Gear lever ........................................... 137
Gear or selector lever (cleaning
guidelines) ......................................... 248
Genuine Mercedes-Benz parts ......... 302
Genuine wood trim and trim strips
(cleaning instructions) ...................... 248
Glove box ........................................... 216
H
Headlamp cleaning system .............. 109
Adding washer fluid .......................241
Notes ............................................. 310
Headlamp mode (daytime driving)
see Daytime running lamps
Headlamps
Cleaning ......................................... 246
Misting up ...................................... 110
Head restraints
Adjusting (electrically) .....................96
Adjusting (manually) ........................95
Adjusting (rear) ................................ 96
Installing/removing (rear) ................96
see NECK-PRO head restraints
(except AMG vehicles)
Heating
see Climate control
High beam flasher ............................. 109
Hill start assist .................................. 135
Hood Closing ........................................... 239
Display message ............................ 200
Opening ......................................... 238
Hydroplaning ..................................... 154
I
Immobilizer .......................................... 66
Instrument cluster Overview .......................................... 26
Submenu (on-board computer) ......178
Warning and indicator lamps ...........27
Instrument cluster lighting ................ 26
Instrument lighting see Instrument cluster lighting
Interior lighting
Automatic control ..........................111
Delayed switch-off (on-board
computer) ...................................... 180
Emergency lighting ........................111
Manual control ............................... 111
Reading lamp ................................. 110
J
Jack Storage location ............................ 253
Using ............................................. 256
Jump-starting ..................................... 262
K
KEYLESS-GO Button ............................................ 132
Convenience closing feature ............85
Display message ............................ 202
Locking ............................................ 71
Starting the engine ........................133
Unlocking ......................................... 71
Key positions
KEYLESS-GO .................................. 132
SmartKey ....................................... 131
Kickdown ................................... 140, 143
Knee bag .............................................. 38
L
LATCH-type (ISOFIX) child seat
anchors ................................................ 58
License plate lamp (display
message) ............................................ 193
Index9BA 204 USA, CA Edition A 2011; 1; 5, en-UShereepeVersion: 3.0.3.62010-05-20T09:17:30+02:00 - Seite 9

PASSENGER AIRBAG OFF indicator
lamp (only USA) ................................... 41
Pedals ................................................. 151
Permanent display (on-board
computer) .......................................... 179
Permanent four-wheel drive see 4MATIC
Plastic trim (cleaning instructions) . 247
Power washers .................................. 244
Power windows see Side windows
Product information ............................ 18
Program selector button .................. 140
Pulling away Automatic transmission .................134
Manual transmission ...................... 134
R
RACETIMER (on-board computer) .... 172
Radio Changing stations (on-board
computer) ...................................... 175
see separate operating instructions
Range (on-board computer) ............. 170
Rear compartment Setting the airflow .........................124
Setting the air vents ......................127
Rear fog lamp (display message) ..... 193
Rear seat backrest Display message ............................ 201
Folding forwards/back ..................218
Rear seat backrest (display
message) ............................................ 201
Rear view camera Function/notes ............................. 162
Rear view camera (cleaning
instructions) ...................................... 247
Rear-view mirror Anti-glare (manual) ..........................99
Dipping (automatic) .......................101
Rear window blind ............................ 222
Rear window heating Malfunction .................................... 125
Switching on/off ........................... 125
Refueling ............................................ 145
Remote control
Programming (garage door
opener) .......................................... 232
Reporting
Malfunctions relevant to safety ........ 21
Reserve fuel
Display message ............................ 197
Warning lamp ................................. 210
Restraint systems
see SRS
Reverse gear
Engaging (manual transmission) ....137
Reversing lamp (display message) .. 193
Roadside Assistance (breakdown) .... 19
Roller blind see Roller sunblind
Roller sunblind
Opening/closing .............................. 89
Panorama roof with power tilt/
sliding panel ..................................... 89
Rear side windows .........................222
Rear window .................................. 222
Roof carrier ........................................ 220
Roof lining and carpets (cleaning
guidelines) ......................................... 249
Route see Route guidance (on-board
computer)
Route guidance (on-board
computer) .......................................... 174
S
Safety Children in the vehicle .....................55
Child restraint systems ....................56
Occupant Classification System
(OCS) ............................................... 41
Overview of occupant safety
systems ........................................... 34
Safety systems
see Driving safety systems
Seat backrest
Adaptive ........................................... 97
Seat belts
Adjusting the height ......................... 53
Belt force limiters ............................ 54
Cleaning ......................................... 249
12IndexBA 204 USA, CA Edition A 2011; 1; 5, en-UShereepeVersion: 3.0.3.62010-05-20T09:17:30+02:00 - Seite 12

Overhead control panelFunctionPage:u To switch the rear
interior lighting on/off
111
;| To switch the
automatic interior lighting
control on/off
111
=p To switch the right-
hand reading lamp on/off
110
?3 To open/close the
tilt/sliding sunroof
88
3 To open/close the
panorama roof with power
tilt/sliding panel with roller
sunblinds
89
Aï Button for MB info call
(mbrace system)
229
BG SOS button (mbrace
system)
227
FunctionPageCRear-view mirror99DIntegrated electronic
compass
235
EButtons for the garage door
opener
232
FMicrophone for mbrace
(emergency call system)
telephone and Voice
Control System 4GF
Roadside Assistance
button (mbrace system)
229
Hp To switch the left-
hand reading lamp on/off
110
Ic To switch the front
interior lighting on/off
1114 The Voice Control System is only available in connection with COMAND. Observe the additional operating
instructions.30Overhead control panelAt a glance
BA 204 USA, CA Edition A 2011; 1; 5, en-UShereepeVersion: 3.0.3.62010-05-20T09:17:30+02:00 - Seite 30

enforcement authority is informed of the
location of the vehicle.
i If the anti-theft alarm system remains
activated for longer than thirty seconds,
mbrace is automatically connected to the
Customer Assistance Center.
Garage door opener
Important safety notes
Up to three different door and gate systems
can be operated using the remote control
integrated in the overhead control panel.
i Certain garage door openers are not
compatible with the integrated remote
control. If you experience difficulties with
the programming of the integrated remote
control, contact an authorized Mercedes-
Benz Center or call the following telephone
assistance service:
R USA: Mercedes-Benz Customer
Assistance Center on
1-800-FOR-MERCedes
R Canada: Customer Service
on1-800-387-0100
GWarning
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent
potential harm or damage. When
programming a garage door opener, the door
moves up or down. When programming a gate
operator, the gate opens or closes.
Do not use the integrated remote control with
any garage door opener that lacks safety stop
and reverse features as required by U.S.
federal safety standards (this includes any
garage door opener model manufactured
before April 1, 1982). A garage door that
cannot detect an object - signaling the door
to stop and reverse - does not meet current
U.S. federal safety standards.
When programming a garage door opener,
park vehicle outside the garage.
Do not run the engine while programming the
integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
exhaust gas contains carbon monoxide (CO),
and inhaling it can cause unconsciousness
and possible death. All exhaust gas contains
carbon monoxide (CO), and inhaling it can
cause unconsciousness and possible death.
i USA only:
This device complies with part 15 of the
FCC rules. Operation is subject to the
following two conditions:
1. The device must not cause harmful
interference.
2. The device must withstand any
interference received, including
interference that may cause undesired
operation.
Unauthorized modification of this device
could void the device's operating permit.
i Canada only:
This device complies with the RSS-210
requirements of Industry Canada.
Operation is subject to the following two
conditions:
1. The device must not cause harmful
interference.
2. The device must accept any interference
received, including interference that may
cause undesired operation.
Unauthorized modification of this device
could void the user's authority to legally
operate the device.
Programming the remote control
Programming
GWarning!
Only press the transmitter button on the
integrated remote control if there are no
persons or objects present within the sweep
232FeaturesLoading, stowing and features
BA 204 USA, CA Edition A 2011; 1; 5, en-UShereepeVersion: 3.0.3.62010-05-20T09:17:30+02:00 - Seite 232

of the garage door. People could otherwise be
injured by the movement of the door.
Remote control in the rear-view mirror
Garage door remote control A is not part of
the garage door opener.
i To achieve the best result, insert new
batteries in garage door remote control
A of your garage door drive before
programming.
XErase the memory of the integrated remote
control ( Y page 235) before programming
it for the first time.XTurn the SmartKey to position 2 in the
ignition lock.XPress and hold one of transmitter
buttons ; to ? on the integrated remote
control.
After a short time, indicator lamp : will
start flashing. It flashes about once per
second.
i Indicator lamp : flashes immediately
the first time that the transmitter button is
programmed. If this transmitter button has
already been programmed, indicator
lamp : will only start flashing at a rate of
once per second after 20 seconds have
elapsed.
XKeep the transmitter button depressed.XPoint transmitter button B of garage door
remote control A towards the transmitter
buttons on the rear-view mirror from a
distance of 2 to 12 inches (5 to 20 cm).i The distance between garage door
remote control A and the integrated
garage door opener depends on the system
of the garage door drive. You might require
several attempts. You should test every
position for at least 20 seconds before
trying another position.XKeep transmitter button B on garage door
remote control A pressed until indicator
lamp : starts to flash rapidly.
The programming has been successful if
indicator lamp : flashes rapidly.XRelease transmitter buttons ;, = or ?
on the integrated remote control or
transmitter button on the garage door
remote control B.
If indicator lamp : goes out after
approximately 20 seconds and has not
flashed rapidly:
XRelease transmitter buttons ;, = or ?
on the integrated remote control or
transmitter button on the garage door
remote control B.XRepeat the procedure for the other
transmitter buttons. When doing so, vary
the distance between the garage door's
remote control and the transmitter buttons
in the rear-view mirror.
i If the garage door system works with a
rolling code, you must synchronize the
remote control integrated into the rear-
view mirror with the garage door system
receiver after programming.
You will find further information in the
garage door opening system's operating
instructions, e.g. the sections on
"Synchronizing the transmitter" or
"Registering a new transmitter". You can
also call the hotline mentioned above.
Notes on programming the remote
control
Canadian radio frequency laws require
transmitter signals to "time-out" (or quit) after
several seconds of transmission. This may
Features233Loading, stowing and featuresBA 204 USA, CA Edition A 2011; 1; 5, en-UShereepeVersion: 3.0.3.62010-05-20T09:17:30+02:00 - Seite 233Z

not be long enough for the integrated signal
transmitter to pick up the signal during
programming. Similar to this Canadian law,
some U.S. gate operators are designed to
"time-out" in the same manner.
If you live in Canada or have difficulties
programming the garage door opener
(regardless of where you live) when using the
programming steps (see above), proceed as
follows:XPress transmitter button ( ;, = or ?) and
hold it down during the following steps until
the setup has been completed
successfully.XAt the same time, press transmitter button
B of the garage door remote control for
two seconds, then release it for two
seconds, then press it again for two
seconds.XRepeat this sequence on transmitter
button B of the garage door remote
control until the frequency signal has been
learned.XIf the setup procedure is successful,
indicator lamp : flashes once slowly and
goes out after a few seconds.XContinue with the other programming
steps (see above).
Problems when programming
If you have problems when programming the
integrated remote control, please note the
following:
R check the transmitter frequency of garage
door remote control A (which can usually
be found on the rear of the remote control).
The integrated remote control is
compatible with equipment that operates
in the frequency range 280 to 390 MHz.
R replace the batteries in garage door remote
control A. This increases the likelihood of
garage door remote control A sending a
strong and precise signal to the integrated
remote control on the rear-view mirror.
R When aiming the garage door remote
control at the transmitter buttons on the
rear-view mirror, hold garage door remote
control A at differing distances and angles
from the transmitter button that you are
programming. Try different angles from a
distance of 2 to 12 inches (5 to 30 cm) or
the same angle from differing distances.
R If there is another garage door remote
control for the same device, perform the
programming steps again using the remote
control. Before performing these steps,
make sure that new batteries have been
installed in the garage door remote control.
R Align the antenna cable of the garage door
opener unit. This can improve signal
reception/transmission.
Opening or closing the garage door
Once programmed, the integrated remote
control will assume the function of the garage
door system's remote control. Please also
read the operating instructions for the garage
door system.
XTurn the SmartKey to position 2 in the
ignition lock.XPress transmitter button ;, = or ? in the
overhead control panel that you have
programmed to operate the garage door.
Garage door system with fixed code:
indicator lamp : lights up continuously.
Garage door system with rolling code:
indicator lamp : flashes briefly and then
lights up for approximately two seconds.
This is repeated for up to 20 seconds.
i The transmitter will transmit a signal for
as long as the transmitter button is being
pressed. The transmission will be halted
after a maximum of 20 seconds and
indicator lamp : will flash. Press the
transmitter button again, if necessary.
234FeaturesLoading, stowing and features
BA 204 USA, CA Edition A 2011; 1; 5, en-UShereepeVersion: 3.0.3.62010-05-20T09:17:30+02:00 - Seite 234