key MERCEDES-BENZ C CLASS COUPE 2004 Service Manual

103
Controls in detail
Lighting
Interior lighting
The controls are located in the overhead
control panel.
1 Rear interior lights
2 Right front reading lamp
3 Rocker switch for automatic control
system
4 Left front reading lamp Activating automatic control

Press the rocker switch
3 to center
position.
Interior lamps are switched on in dark-
ness, when you

unlock the vehicle


open a door


remove the SmartKey from starter
switch
The interior lamps are switched off follow-
ing a preset time (
page 128). Deactivating automatic control

Press the
=symbol on rocker
switch 3.
The interior lighting remains switched
off, even when you

unlock the vehicle


open a door


remove the SmartKey from the
starter switch
Manual control
Switching all front interior lights on and
off

Press the Wsymbol on rocker
switch 3.
The front interior lights come on.

Press rocker switch 3 to center
postion to activate the automatic
control.
iIf the door remains open, the interior
lamps switch off automatically after ap-
proximately five minutes, when the
SmartKey is removed or in the starter
switch position 0.
An interior lamp switched on manually
does not go out automatically.

106 Controls in detailInstrument clusterCoolant temperature displayTurn the SmartKey in the starter switch to
position1 or 2.

Call up the trip odometer and main
odometer by pressing button è
or ÿ on the multifunction steering
wheel (
page 110).

Press button j ork until the
coolant temperature display appears. During severe operating conditions e.g.
stop-and-go city traffic, the coolant tem-
perature may rise close to 248°F (120°C).
The engine should not be operated with
the coolant temperature above 248°F
(120°C). Doing so may cause serious en-
gine damage which is not covered by the
Mercedes-Benz Limited Warranty.
Warning!
G


Driving when your engine is badly over-
heated can cause some fluids which
may have leaked into the engine com-
partment to catch fire. You could be se-
riously burned.


Steam from an overheated engine can
cause serious burns and can occur just
by opening the engine hood. Stay away
from the engine if you see or hear steam
coming from it.
Turn off the engine, get out of the vehicle
and do not stand near the vehicle until it has
cooled down.
iExcessive coolant temperature trigger
a warning in the multifunction display.

109
Controls in detail
Control system
 Control system
The control system is activated as soon as
the SmartKey in the starter switch is
turned to position 1. The control system
enables you to

call up information about your vehicle


change vehicle settings
For example, you can use the control sys-
tem to find out when your vehicle is next
due for service, to set the language for
messages in the instrument cluster dis-
play, and much more.
The control system relays information to
the multifunction display.
Multifunction display
1 Outside temperature
2 Main odometer
3 Trip odometer
4 Automatic transmission program mode
5 Current gear selector lever position
6 Digital clock
iThe displays for the audio systems (ra-
dio, CD player, cassette player) will ap-
pear in English, regardless of the
language selected.
Warning!
G
A driver’s attention to the road and traffic
conditions must always be his /her primary
focus when driving.
For your safety and the safety of others, se-
lecting features through the multifunction
steering wheel should only be done by the
driver when traffic and road conditions per-
mit it to be done safely.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 13.5 m) every second.

115
Controls in detail
Control system
Select radio station
Turn on the radio (
page 160). Vehi-
cles with COMAND*: Refer to separate
operating instructions.

Press button è orÿ repeatedly
until you see the currently tuned sta-
tion in the display.
1 Station frequency
2 Waveband setting
3 Setting for station selection using
memory

Press button k orj repeatedly
until the desired station is found.
The type of search depends on the set-
ting for the station tuning
(page 128):


The next stored station is selected
(SP)


Station search Select satellite radio station*
The Sirius-Satellite-Radio is treated as a ra-
dio application.

Select SAT radio with the correspond-
ing softkey in the radio menu.
1 Channel name or number
2 SAT mode and preset number
3 Setting for station selection using
memory

Press button k orj repeatedly
until the desired channel is found.
iYou can only store new stations using
the corresponding feature on the radio
(page 165).
Vehicles with COMAND*: Refer to sep-
arate operating instructions.
You can also operate the radio in the
usual manner.

116 Controls in detailControl system
Operate the CD player*
Turn on the radio and select the CD
player (
page 175). Vehicles with CO-
MAND*: Refer to separate operating in-
structions.

Press button è orÿ repeatedly
until the settings for the CD currently
being played are shown in the display.
1 Current track
2 Current CD (for CD changer*)

Press button k orj repeatedly
until the desired track is selected. Operate the cassette player*

Turn on the radio and select the cas-
sette player (
page 116). Vehicles
with COMAND*: Refer to separate op-
erating instructions.

Press button è orÿ repeatedly
until the settings for the cassette cur-
rently being played are shown in the
display.
1 Current side

Press button j to fast forward to
the next track.

Press button k to rewind the cas-
sette to the beginning of the current
track.
iFeature description is based on prelim-
inary information available at time of
printing.
For more information on satellite radio
operation, see “Satellite radio (SAT)*
(USA only)” (
page 168)
Vehicles with COMAND*: Refer to sep-
arate operating instructions.
iTo select a CD from the magazine,
press a number on the audio system or
the COMAND* system key pad located
in the center dashboard.

118 Controls in detailControl systemMalfunctions have occurred
If malfunctions have occurred, you will see
the number of malfunctions in the display:1 Number of malfunctions
Press button k orj .
The stored messages will now be dis-
played in order. For malfunction and
warning messages, see “Messages in
the display” (
page 264). Should any malfunctions occur while driv-
ing, the number of malfunctions will reap-
pear in the display when the SmartKey in
the starter switch is turned to position
0 or
removed from the starter switch.
Settings menu
In the
SETTINGS
menu there are two func-
tions:


The function
RESET TO FACTORY SET-
TINGS
, with which you can reset all the
settings to the original factory settings.


A collection of submenus with which
you can make individual settings for
your vehicle.

Press button è orÿ repeatedly
until the
SETTINGS
menu is seen in the
display.
iThe message memory will be cleared
when you turn the SmartKey in the
starter switch to position 1 or 2. You
will then only see high-priority
messages in the multifunction display
(page 264).

119
Controls in detail
Control system
Resetting all settings
You can reset all the functions of all sub-
menus to the factory settings.
Press the reset button in the instru-
ment cluster (
page 22) for approxi-
mately three seconds.
In the display you will see the request
to press the reset button again to con-
firm.

Press the reset button again.
The functions of all the submenus will
reset to factory settings. Submenus in the Settings menu

Press button
k orj .
In the display you see the collection of
the submenus.

Press button ç.
The selection marker moves to the next
submenu.
iThe settings you have changed will not
be reset unless you confirm the action
by pressing the reset button a second
time. Approximately five seconds after
pressing the reset button for the sec-
ond time, the
SETTINGS
menu reap-
pears in the display.
For safety reasons, the following func-
tions are not reset while driving:


the
LIGHT CIRCUIT HEADLIGHT MODE

function in the LIGHTING submenu


the
SETTINGS KEY-DEPENDENT
func-
tion in the CONVENIENCE submenu

121
Controls in detail
Control system
The table below shows what settings can
be changed within the various menus. De-
tailed instructions on making individual
settings can be found on the following
pages.INSTRUMENT CLUSTER
LIGHTING
VEHICLE
CONVENIENCE
Set time (hours)
Set daytime running lamp mode
(USA only)
Set station selection mode
(radio)
Activate easy-entry/exit feature
Set time (minutes)
Set locator lighting
Set automatic locking
Set key-dependency
Select time display mode
Exterior lamps delayed shut-off
Set parking position for exterior
rear view mirror
Select temperature display
mode
Interior lighting delayed shut-off
Select speedometer display
modeSelect languageSelect display (speed display or
outside temperature)

126 Controls in detailControl system
With daytime running lamp mode se-
lected and the exterior lamp switch at
position0, the following lamps will
c o m e o n a u t o m a t i c a l l y w h e n t h e
engine is turned on:

Parking lamps and low beam head-
lamps


License plate lamps in low ambient
light conditions Setting locator lighting
During darkness, the following lamps will
come on when the exterior lamp switch is
in position
U, the locator lighting fea-
ture is activated, and the vehicle is un-
locked by SmartKey:


Parking lamps


Tail lamps


License plate lamps


Front fog lamps
To activate locator lighting:

Make sure the function
LOCATOR
LIGHTING
is set.

Turn the exterior lamp switch to posi-
tion U .
The locator lighting switches off when the
driver’s door is opened. It switches off au-
tomatically after a period of approximately
40 seconds.

Move the selection marker with
the æ orç button to the
LIGHT-
ING
submenu.

Press button j ork repeatedly
until you see this message in the dis-
play:
LOCATOR LIGHTING
.
The selection marker is on the current
setting.

Press æ orç to select the de-
sired setting.
The locator lighting will be switched on
or off.
iIf you turn the exterior lamp switch to
another position, the corresponding
lamp(s) will switch on.
For safety reasons, resetting the LIGHTING
submenu to factory settings
(
page 120) while driving will not re-
set the daytime running lamp mode.
In the display you will then see the mes-
sage:
LIGHTING – CANNOT BE TOTALLY
RESET TO FACTORY SETTINGS WHILE
DRIVING.


127
Controls in detail
Control system
Setting night security illumination
(Exterior lamps delayed shut-off)
Use the
HEADLIGHTS DELAYED SHUT-OFF

function to set whether and for how long
you would like the exterior lamps to illumi-
nate during darkness after all doors are
closed.
When the delayed shut-off feature is acti-
vated and the exterior lamp switch is in po-
sition U, the following lamps will
remain lit after you remove the SmartKey
from the starter switch:


Parking lamps


Tail lamps


License plate lamps


Front fog lamps To activate night security illumination:

Select delayed shut-off period (see be-
low).

Turn the exterior lamp switch to posi-
tion
U .
To select delayed shut-off period:

Move the selection marker with
the æ orç button to the
LIGHT-
ING
submenu.

Press button j ork repeatedly
until you see this message in the dis-
play:
HEADLIGHTS DELAYED SHUT-OFF
.
The selection marker is on the current
setting.

Press æ orç to select the de-
sired lamp-on period.
You can select:

0 s
, the delayed shut-off feature is
deactivated


15 s
, 30 s
, 45 s
or
60 s
, the delayed
shut-off feature is activated
You can temporarily deactivate the de-
layed shut-off feature:

Before leaving the vehicle turn the
SmartKey in the starter switch to
position 0.

Then turn it to position 2 and back
to 0.
The delayed shut-off feature is deacti-
vated. It will reactivate as soon as you
reinsert the SmartKey in the starter
switch.
iYou can reactivate this function within
ten minutes by opening a door.
If you do not open a door after remov-
ing the SmartKey, the lamps will auto-
matically switch off after 60 seconds.