lock MERCEDES-BENZ C-Class COUPE 2017 CL205 Owner's Manual

Vehicles with aluminum hub cap:
XTo remove:take socket;and lu gwrench
= from the vehicl etool kit (Ypage 300).
XPosition socket ;on hubc ap:.
XPosition lu gwrench =on socket ;.
XUsing lugwrench =,turn hubc ap: coun-
ter-clockwise and remove it.
XTo install: before installing, check hubc ap:
and the wheel are afor soiling and clean if
necessary.
XPuth ubcap :in position and turn unti litisin
the right position.
XPosition socket ;on hubc ap:.
XAttach lu gwrench =to socket ;and
tighten hubc ap:.
The tightening torque mus tbe
18 lb-ft (2 5Nm).
iNote that the hubc ap shouldbetightened
to the specified torque of 18 lb-ft (25 Nm).
Mercedes-Benz recommend sthat yo uhave
the hubc ap installed at aquali fied specialist
workshop.
XUsing lu gwrench =,loosent he bolts on the
wheel yo uwishtoc hange by abouto ne full
turn. Do not unscrew the bolts completely.
The jacking points are locate djust behind the
front wheel housing sand jus tinfront of the rear
wheel housing s(arrows).
Mercedes-AMG vehicle sand vehicle swith
AMG equipment: to protect the vehicl ebody,
the vehicl ehascovers installed next to the jack-
ing points on the outer sills.
XMercedes-AMG vehicle sand vehicles
with AMG equipment: foldc over ?
upwards.
XPosition jack Bat jacking point A.
338Changingawheel
Wheelsand tires

XMake sure the foot of the jack is directly
beneath the jackingpoint.
XTurn crankCclockwise until jack Bsits
completely on jackingp ointA.T he base of
the jack must lie evenly on the ground.
XTurn crank Cuntil the tire is raised amaxi-
mum of 1.2 in (3 cm) from the ground.
Removing awheel
!Mercedes-AMG vehiclesw ith ceramic-
brake disc: during removal and repositioning
of the wheel, the wheel rim can strike the
ceramic-brake disc and damage it. Therefore,
you should proceed carefully and get asec-
ond person assist to you. Alternatively, you
can use asecond alignment bolt.
!Do not place wheel bolts in sand or on adirty
surface. The bolt and wheel hub threads could
otherwise be damaged when you screw them
in.
When mounting/removing wheels, and for as
long as the wheels are removed, avoid applying
any external force on the brake disks. This could
impair the level of comfort when braking.
XUnscrew the uppermost wheel bolt com-
pletely.
XScrew alignment bolt :into the thread
instead of the wheel bolt.
XUnscrew the remaining wheel bolts fully.
XRemove the wheel.
Mounting anew wheel
GWARNING
Oiled or greased wheel bolts or damaged
wheel bolts/hub threads can cause the wheel bolts to come loose. As aresult, you could
lose awheel while driving. There is arisk of
accident.
Never oil or grease wheel bolts. In the event of
damage to the threads, contact aqualified
specialist workshop immediately. Have the
damaged wheel bolts or hub threads
replaced/renewed. Do not continue driving.
GWARNING
If you tighten the wheel bolts or wheel nuts
when the vehicle is raised, the jack could tip
over. There is arisk of injury.
Only tighten the wheel bolts or wheel nuts
when the vehicle is on the ground.
Always pay attention to the instructions and
safety notes in the "Changing awheel" section
(
Ypage 335).
Only use wheel bolts that have been designed
for the wheel and the vehicle. For safety rea-
sons, Mercedes-Benzr ecommends that you
only use wheel bolts which have been approved for Mercedes-Benzv ehicles and the respective
wheel.
!Mercedes-AMG vehiclesw ith ceramic-
brake disc: during removal and repositioning
of the wheel, the wheel rim can strike the
ceramic-brake disc and damage it. Therefore,
you should proceed carefully and get asec-
ond person assist to you. Alternatively, you
can use asecond alignment bolt.
!To prevent damage to the paintwork, hold
the wheel securely against the wheel hub
while screwing in the first wheel bolt.
Changing awheel339
Wheels and tires
Z

XClean thewheel and wheel hub contact sur-
faces.
XSlid ethe wheel to bemounte dontot he align-
men tbolt and push iton.
XTighte nthe wheel boltsuntilthey are finger-
tight.
XUnscrew th ealignmen tbolt.
XTighte nthe last wheel boltuntil it is finger-
tight.
Lowering th evehicle
GWAR NING
The wheelsc ouldwork looseift hewheel nuts
and boltsare no ttightened to th especifie d
tightening torque. Thereisar iskofa cciden t.
Hav ethe tightening torque immediately
checked at aqualified specialist workshop
after awheel ischanged.
XTurn th ecrank of th ejackc ounter-clock wise
unt ilth ev ehicle is once again standing firmly
on th eground.
XPlacet hejacktoo neside.
XTighte nthe wheel boltsevenly inac rosswise
pattern inthes equenc eindicated (: toA). The specifie
dtightening torque is 96lb-ft
(1 30 Nm) .
XTurn th ejackb ack to its initial position.
XStow th ejac ka nd th erestoft hevehicle tools
in thet runk again.
XMercedes-AM Gvehicles and vehicles
with AMG equipment: insert thecover into
th eo uter sill.
XCheckt hetirep ressureoft henewly mounted
wheel and adjust it if necessary.
Observ ethe recommended tir epressure
(
Ypage 319).
When you are driving withthe collapsible spare
wheel mounte d,thet irep ressurel oss warning
system or th etirep ressurem onitorcanno tfunc-
tio nr eliably. Only restartthe tirep ressurel oss
warning system or tir epressurem onitorwhen
th ed efective wheel has been replace dwitha
ne ww heel.
Vehicles with atirep ressure control sys-
tem: all installed wheelsm ust be equippedwith
functioning sensors.
Wheel-tire combination
You can ask for informatio nregardin gpermitted
wheel-tire co mbinations at an authorized
Mercedes-Ben zCenter.
!For safety reasons, Mercedes-Ben zrecom-
men dsthat you only use tires and wheels
whic hhave been approvedbyM ercedes-Benz
specifically for your vehicle.
Theset ires have been specially adapted for
use witht hecontrol systems ,suchasA BSor
ESP
®,a nd are marke dasfollows:
RMO= Mercedes-Ben zOriginal
RMOE = Mercedes-Ben zOriginal Extended
(tires featurin grun-flat characteristics)
RMO1 = Mercedes-Ben zOriginal (only cer-
tain AM Gtires)
Mercedes-Ben zOriginal Extende dtires may
only be used on wheelst hath ave been spe-
cificall yapprove dbyMercedes-Benz.
Only use tires, wheelsora ccessoriestested
and approve dbyMercedes-Benz. Certain
characteristics, e.g .handling, vehicle noise
emissionsorf uel consumption,m ay other-
wise be adverselyaffected. In addition,w hen
driv ingwithal oad, tir edimension variations
could caus ethe tires to come int ocontac t
340Wheel-tirec ombination
Wheels and tires

The antifreeze concentrate/corrosion inhibitor
concentration in the engine cooling system
should:
Rbe at least 50%. This will protectthe engine
cooling system against freezin gdown to
approximately -35 ‡(-37 †).
Rnot exceed 55% (antifreez eprotection down
to -49 ‡[-45 †]) .Otherwise, hea twilln ot be
dissipated as effectively.
Mercedes-Benz recommends an antifreeze/
corrosion inhibito rconcentrate in accordance
with MB Specifications for Service Products
310.1.
iWhe nthe vehicl eisfirst delivered, it is filled
with acoolant mixture thate nsures adequate
antifreeze and anti-corrosion protection.
iThe coolant is checked with every mainte-
nance intervalataq ualified specialist work-
shop.
Fillin gcapacities
ModelCapacity
Mercedes ‑AMG
vehicles12.6 US qt (11.9 l)
Allo ther models9.5 US qt (9.0 l)
Windshield washe rsystem
Important safety notes
GWARNING
Windshiel dwasher concentrate coul dignite if
it comes into contact with hot engine compo-
nents or the exhaust system. There is arisk of
fire and injury.
Make sure that no windshield washer con-
centrate is spilled next to the filler neck.
!Only use washer flui dthat is suitabl efor
plastic lam plenses, e.g. MB SummerFi torMB
WinterFit. Unsuitabl ewasher flui dcoul ddam-
age the plastic lense softhe headlamps.
!Only MB SummerFi tand MB WinterFit
washer flui dshould be mixed together. The
sprayn ozzles may otherwise become
blocked. Do not use distille
dorde-ionized water, other-
wise, the leve lsensor may give afals ereading.
When handling washer fluid, observe the impor-
tant safety notes on service products
(
Ypag e344).
At temperatures above freezing:
XFill the washer flui dreservoir with amixture of
water and windshield washer fluid, e.g. MB
SummerFit.
Add 1part MB SummerFi tto100 parts water.
At temperatures below freezing:
XFill the washer flui dreservoir with amixture of
water and washer fluid, e.g. MB WinterFit.
For the correct mixing ratio refer to the infor-
mation on the antifreeze reservoir.
iAdd windshield washer fluid, e.g. MB Sum-
merFit or MB WinterFit, to the washer flui dall
yea rround.
Climate control systemr efrigerant
Important safety notes
The climate control syste mofyourvehicleisf il-
led with refrigerant R ‑134a.
The instructio nlabel regarding the refrigerant
type use dcan be found on the radiator cross
member.
!Only the refrigerant R ‑134a and the PAG oil
approved by Mercedes-Benz may be used.
The approved PAG oil may not be mixed with
any other PAG oil that is not approved for
R-134a refrigerant. Otherwise, the climate
control syste mmay be damaged.
Service work, such as refilling with refrigerant or
replacing component parts, may only be carried
out by aqualified specialist workshop. All appli-
cabl eregulations, as wel lasSAE standard J639,
must be adhered to.
Always have work on the climate control system
carrie dout at aqualified specialist workshop.
348Service products and filling capacities
Technical data