antifreeze MERCEDES-BENZ C230 2007 W203 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: C230, Model: MERCEDES-BENZ C230 2007 W203Pages: 441
Page 279 of 441
278 Operation
Engine compartment
Coolant level
The engine coolant is a mixture of water
and anticorrosion/antifreeze. To check
the coolant level, the vehicle must be
parked on level ground and the engine
must be cool.
The coolant expansion tank is located on
the passenger side of the engine compart-
ment.
1Coolant expansion tank
2CapUsing a rag, turn cap2 slowly approx-
imately one half turn counterclockwise
to release any excess pressure.
Continue turning the cap counterclock-
wise and remove it.
The coolant level is correct if the level
for cold coolant: reaches the black
top part of the reservoir
for warm coolant: is approx. 0.6 in
(1.5 cm) higher
Add coolant as required.
Replace and tighten cap.
For more information on coolant, see
“Coolants” (
page 416).
Warning!G
In order to avoid any potentially serious
burns:
Use extreme caution when opening the
hood if there are any signs of steam or
coolant leaking from the cooling system,
or if the coolant temperature gauge indi-
cates that the coolant is overheated.
Do not remove pressure cap on coolant
reservoir if coolant temperature is
above 158°F (70°C). Allow engine to
cool down before removing cap. The
coolant reservoir contains hot fluid and
is under pressure.
Using a rag, slowly open the cap
approximately1/2 turn to relieve excess
pressure. If opened immediately, scald-
ing hot fluid and steam will be blown out
under pressure.
Do not spill antifreeze on hot engine
parts. Antifreeze contains ethylene
glycol which may burn if it comes into
contact with hot engine parts.
Page 281 of 441
280 Operation
Engine compartment
Windshield washer system and
headlamp cleaning system*
The windshield washer reservoir is located
in the engine compartment.
1Washer fluid reservoirFluid for the windshield washer system and
the headlamp cleaning system* is supplied
from the windshield washer reservoir. It
has a capacity of:
3.2 US qt (3.0 l) in vehicles without
headlamp cleaning system
6.4 US qt (6.0 l) in vehicles with
headlamp cleaning system
During all seasons, add MB Windshield
Washer Concentrate “MB SummerFit” to
water. Premix the windshield washer fluid
in a suitable container.
Refill the reservoir with MB Windshield
Washer Concentrate and water (or
commercially available premixed
windshield washer solvent/antifreeze,
depending on ambient temperatures).
For more information, see “Windshield
washer and headlamp cleaning system*”
(
page 418).Warning!G
Washer solvent/antifreeze is highly flamma-
ble. Do not spill washer solvent/antifreeze
on hot engine parts, because it may ignite
and burn. You could be seriously burned.
!Always use washer solvent/antifreeze
where temperatures may fall below the freezing
point. Failure to do so could result in damage to
the washer system/reservoir.
!Only use washer fluid which is suitable for
plastic lenses. Improper washer fluid can dam-
age the plastic lenses of the headlamps.
Page 309 of 441
308 Operation
Winter driving
Before the onset of winter, have your
vehicle winterized at an authorized
Mercedes-Benz Center. This service
includes:
Check of anticorrosion and antifreeze
concentration.
Addition of cleaning concentrate to the
water of the windshield and headlamp
cleaning system. Add MB Concentrate
“MB SummerFit” to a premixed wind-
shield washer solvent/antifreeze
which is formulated for below freezing
temperatures (
page 418).
Battery test. Battery capacity drops
with decreasing ambient temperature.
A well charged battery helps to make
sure that the engine can be started,
even at low ambient temperatures.
Tire change.
Winter tires
Always use winter tires at temperatures
below 45°F (7°C) and whenever wintry
road conditions prevail. Not all M+S rated
tires provide special winter performance.
Make sure the tires you use show M+S and
the mountain/snowflake.marking on
the tire sidewall. These tires meet specific
snow traction performance requirements
of the Rubber Manufacturers Association
(RMA) and the Rubber Association of Can-
ada (RAC) and have been designed specif-
ically for use in snow conditions. Use of
winter tires is the only way to achieve the
maximum effectiveness of the ABS, ESP
®,
and 4MATIC in winter operation.
For safe handling, make sure that all
mounted winter tires are of the same make
and have the same tread design.Always observe the speed rating of the
winter tires installed on your vehicle. If the
maximum speed for which your tires are
rated is below the speed rating of your
vehicle, you must place a notice to this
effect where it will be seen by the driver.
Such notices are available from your tire
dealer or from any authorized
Mercedes-Benz Center.
Warning!G
Winter tires with a tread depth of less than 1/6in (4 mm) must be replaced. They are no
longer suitable for winter operation.
Page 346 of 441
345 Practical hints
What to do if …
Display symbolDisplay messagePossible cause/consequencePossible solution
BTop up
coolant
See
Operator’s
ManualThe coolant level is too low.Add coolant (page 278).
If you have to add coolant frequently,
have the cooling system checked by
an authorized Mercedes-Benz Center.
Warning!G
Do not spill antifreeze on hot engine parts.
Antifreeze contains ethylene glycol which
may burn if it comes into contact with hot
engine parts. You could be seriously burned.
!Do not ignore the low engine coolant level
warning. Extended driving with the message and
symbol displayed may cause serious engine
damage not covered by the Mercedes-Benz Lim-
ited Warranty.
Do not drive without sufficient amount of coolant
in the cooling system. The engine will overheat
causing major engine damage.
Page 411 of 441
410 Technical data
Fuels, coolants, lubricants, etc.
ModelCapacityFuels, coolants, lubricants, etc.
Rear axleC 230 (all models)
C 280 (all models)
C 350
C 350 Sport
C 350 4MATIC1.0 US qt (1.0 l)
1.2 US qt (1.1 l)
1.2 US qt (1.1 l)
1.2 US qt (1.1 l)
1.0 US qt (1.0 l)Hypoid gear oil SAE 85 W 90
Front axleC 280 4MATIC
C 350 4MATIC0.5USqt (0.46l)Hypoid gear oil SAE 85 W 90
Transfer caseC 280 4MATIC
C 350 4MATICapprox. 0.62 US qt
(0.59 l)MB Transfer case fluid
Power steeringapprox. 1.1 US qt (1.0 l)MB Power Steering Fluid (Pentosin
CHF 11S)
Front wheel hubsapprox. 2.1oz (60g)
eachHigh temperature roller bearing grease
Brake system0.5 US qt (0.5 l)MB Brake Fluid (DOT 4+)
Cooling systemapprox. 7.8 US qt (7.4 l)MB 325.0 Anticorrosion/antifreeze
agent
Page 412 of 441
411 Technical data
Fuels, coolants, lubricants, etc.
ModelCapacityFuels, coolants, lubricants, etc.
Fuel tank
including
a reserve of16.4 US gal (62.0 l)
2.1 US gal (8.0 l)Premium unleaded gasoline:
Minimum Posted Octane 91
(Avg. of 96 RON/86 MON)
C 230/C 230 Sport:
Flexible Fuel Vehicle (identified by a label
reading Premium gasoline or E85 only!
on fuel filler flap):
Alternative fuel: Ethanol fuel (E85)
Air conditioning systemR-134a refrigerant and special PAG lubri-
cant oil (never R-12)
Windshield washer3.2 US qt (3.0 l)MB Windshield Washer Concentrate1
Windshield washer and headlamp
cleaning system*6.4 US qt (6.0 l)
1Use MB Windshield Washer Concentrate “MB SummerFit” and water for temperatures above freezing point or MB Windshield Washer Concentrate “MB SummerFit”
and commercially available premixed windshield washer solvent/antifreeze for temperatures below freezing point. Follow suggested mixing ratios (page 418).
Page 417 of 441
416 Technical data
Fuels, coolants, lubricants, etc.
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which
provides:
Corrosion protection
Freeze protection
Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -22°F (-30°C) and
corrosion protection.
If the antifreeze mixture is effective
to -22°F (-30°C), the boiling point of the
coolant in the pressurized cooling system
is reached at approx. 266°F (130°C).The coolant solution must be used
year-round to provide the necessary corro-
sion protection and increase boil-over
protection. Refer to Maintenance Booklet
for replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance Booklet is only applicable
if MB 325.0 anticorrosion/antifreeze
solution or other Mercedes-Benz approved
products of equal specification (see
Factory Approved Service Products
pamphlet) are used to renew the coolant
concentration or bring it back up to the
proper level.
To provide important corrosion protection,
the solution must be at least 45%
anticorrosion/antifreeze [equivalent to
freeze protection to approx. -22°F
(-30°C)]. If you use a solution that is more than 55%
anticorrosion/antifreeze [freeze
protection to approx. -49°F (-45°C)], the
engine temperature will increase due to
the lower heat transfer capability of the
solution. Therefore, do not use more than
this amount of anticorrosion/antifreeze.
If the coolant level is low, water and
MB 325.0 anticorrosion/antifreeze should
be used to bring it up to the proper level
(have cooling system checked for signs of
leakage). Please make sure the mixture is
in accordance with label instructions.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality,
consult an authorized Mercedes-Benz
Center.
!Add premixed coolant solution only. Adding
water and MB 325.0 Anticorrosion/Antifreeze
separately from each other, could cause engine
damage not covered by the Mercedes-Benz
Limited Warranty
Page 418 of 441
417 Technical data
Fuels, coolants, lubricants, etc.
Anticorrosion/antifreeze
Your vehicle contains a number of
aluminum parts. The use of aluminum
components in motor vehicle engines
necessitates that anticorrosion/antifreeze
coolant used in such engines be specifi-
cally formulated to protect the aluminum
parts.
Failure to use such anticorrosion/anti-
freeze coolant will result in a significantly
shortened service life.
Therefore, the following product is strongly
recommended for use in your vehicle:
Mercedes-Benz 325.0
Anticorrosion/Antifreeze Agent.Before the start of the winter season (or
once a year in hot southern regions), you
should have the anticorrosion/antifreeze
concentration checked. The coolant is also
regularly checked each time you bring your
vehicle to an authorized Mercedes-Benz
Center for service.Anticorrosion/antifreeze quantity
ModelApprox. freeze protection
–35°F
(–37°C)–49°F
(–45°C)
all
models3.8 US qt
(3.6 l)4.1 US qt
(3.9 l)
Page 419 of 441
418 Technical data
Fuels, coolants, lubricants, etc.
Windshield washer and headlamp
cleaning system*
Both the windshield washer and headlamp
cleaning system* are supplied from the
windshield washer fluid reservoir.
The washer fluid reservoir has a capacity of
approx.:
3.2 US qt (3.0 l) in vehicles without
headlamp cleaning system*
6.4 US qt (6.0 l) in vehicles with
headlamp cleaning system*
Refill the reservoir with MB Windshield
Washer Concentrate “MB SummerFit”
and water (or concentrate and com-
mercially available premixed wind-
shield washer solvent/antifreeze,
depending on ambient temperatures).Windshield and headlamp washer fluid
mixing ratio
For temperatures above freezing point, use
MB Windshield Washer Concentrate
“MB SummerFit” and water:
1 part “MB SummerFit” to 100 parts
water
(1.34 fl oz [40 ml] “MB SummerFit” to
1 gallon [4.0 l] water)
For temperatures below freezing point, use
MB Windshield Washer Concentrate
“MB SummerFit” and commercially avail-
able premixed windshield washer sol-
vent/antifreeze:
1 part “MB SummerFit” to 100 parts
solvent
(1.34 fl oz [40 ml] “MB SummerFit” to
1 gallon [4.0 l] solvent)
Warning!G
Washer solvent/antifreeze is highly flamma-
ble. Do not spill washer solvent/antifreeze
on hot engine parts, because it may ignite
and burn. You could be seriously burned.
Page 420 of 441
419 Index
A
ABS 25, 82
Malfunction indicator lamp 322, 323
Messages in display 335
Accelerator position,
automatic transmission 155
Accessory weight 304
Accident
In case of 53
Active head restraints
see Head restraints
Additional turn signals 368
Air bags 59
Children 75
Front passenger front air bag off
indicator lamp 27, 68, 331
Front, Driver 63
Front, Passenger 63
Passenger 63
Safety guidelines 62
Side impact (front and rear*) 64
Window curtain 64Air conditioning refrigerant 412
Air conditioning system
Automatic climate control* 174
Climate control 164
Air conditioning, Cooling
Automatic climate control* 184
Climate control 172
Air distribution
Automatic climate control* 178
Climate control 168
Air pressure see Tire inflation pressure
Air recirculation mode
Automatic climate control* 181
Climate control 170
Air vents, Front
Automatic climate control* 175
Climate control 165Air vents, Rear
Automatic climate control* 186
Climate control 173
Air volume
Automatic climate control* 179
Climate control 168
Alignment bolt (vehicle tool kit) 379
Anticorrosion/antifreeze 417
Antiglare, Rear view mirror 160
Anti-theft systems 89
Anti-theft alarm system* 89
Immobilizer 89
Aquaplaning see Hydroplaning
Armrest 238
Ashtrays 241
Aspect ratio 304
ATF (Automatic transmission fluid) 277
AUDIO menu
Search function 142
AUDIO menu (Control system) 127