hood release MERCEDES-BENZ C240 4MATIC 2004 W203 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2004, Model line: C240 4MATIC, Model: MERCEDES-BENZ C240 4MATIC 2004 W203Pages: 400, PDF Size: 5.04 MB
Page 21 of 400
21 At a glance
Cockpit
Item
Page
1
Combination switch
Turn signals
47
Windshield wipers
47
High beam
47
2
Cruise control lever
206
3
Instrument cluster
22,
109
4
Multifunction steering
wheel
24,
114
5
Lever for voice control
system*, see separate
operating instructions
Item
Page
6
Overhead control panel
27
7
Glove box lid release, glove
box lock
216
8
Glove box
216
9
Center console
25
a
Starter switch
31
b
Horn
c
Steering wheel adjustment
handle (manual)
37
d
Steering wheel adjustment
stalk (electrical)*
37
Item
Page
e
Hood lock release
252
f
Parking brake pedal
45, 50
g
Trunk lid release switch
86
h
Door control panel
28
j
Parking brake release
45
k
Exterior lamp switch
102
l
Exterior rear view mirror
adjustment
38
m
Headlamp washer switch*
148
Page 252 of 400
252 OperationEngine compartment
Engine compartmentHood
Opening
1Hood release
Pull lever1 downwards.
The hood is unlocked and handle2
will extend out of the radiator grille. 2Handle for opening the hood
Pull handle2 to its stop out of
radiator grille.
Pull up on the hood (do not pull up on
the handle) and then release it.
The hood will be automatically held
open at shoulder height by gas-filled
struts.
Warning!
G
Do not pull the release lever while the
vehicle is in motion. Otherwise the hood
could be forced open by passing air flow.
!To avoid damage to the windshield
wipers or hood, never open the hood if
the wiper arms are folded forward away
from the windshield.
Warning!
G
To help prevent personal injury, stay clear of
moving parts when the hood is open and the
engine is running. Make sure the hood is
properly closed before driving. When closing
the hood, use extreme caution not to catch
hands or fingers.
The radiator fan may continue to run for
approximately 30 seconds or even restart
after the engine has been turned off. Stay
clear of fan blades.Warning!
G
If you see flames or smoke coming from the
engine compartment, or if the coolant tem-
perature gauge indicates that the engine is
overheated, do not open the hood. Move
away from vehicle and do not open the hood
until the engine has cooled. If necessary,
call the fire department.
Page 257 of 400
257 Operation
Engine compartment
Coolant level
The engine coolant is a mixture of water
and anticorrosion/antifreeze. To check
the coolant level, the vehicle must be
parked on level ground and the engine
must be cool.
The coolant expansion tank is located on
the passenger side of the engine compart-
ment.
1Coolant expansion tank
Using a rag, turn cap slowly approxi-
mately one half turn to the left to
release any excess pressure.
Continue turning the cap to the left and
remove it.
The coolant level is correct if the level
for cold coolant: reaches the black
top part of the reservoir
for warm coolant: is approx. 0.6 in
(1.5 cm) higher
Add coolant as required.
Replace and tighten cap.
For more information on coolant, see
“Coolants” (
page 356).
Warning!
G
In order to avoid any possibly serious burns:
Use extreme caution when opening the
hood if there are any signs of steam or
coolant leaking from the cooling system,
or if the coolant temperature gauge indi-
cates that the coolant is overheated.
Do not remove pressure cap on coolant
reservoir if engine temperature is
above 194°F (90°C). Allow engine to
cool down before removing cap. The
coolant reservoir contains hot fluid and
is under pressure.
Using a rag, slowly open the cap
approximately
1/2 turn to relieve excess
pressure. If opened immediately, scald-
ing hot fluid and steam will be blown out
under pressure.
Do not spill antifreeze on hot engine
parts. Antifreeze contains ethylene
glycol which may burn if it comes into
contact with hot engine parts.
Page 316 of 400
316 Practical hintsReplacing wiper blades
Replacing wiper bladesRemoving wiper blades
Fold the wiper arm forward.
1Lock
2Unlock
Pull the tab in direction of arrow2 and
remove windshield wiper.
Installing wiper blades
Slide the wiper blade into the cutout on
the wiper arm.
Slide the tab back in the direction of
arrow1 until it audibly engages.
Fold the wiper arm backward to rest on
the windshield. Make sure you hold on
to the wiper when folding the wiper arm
back.
Warning!
G
For safety reasons, remove SmartKey from
starter switch before replacing a wiper
blade. Otherwise the motor could suddenly
turn on and cause injury.
!Never open the hood when the wiper
arms are folded forward.
Hold on to the wiper when folding the
wiper arm back. If released, the force
of the impact from the tensioning
spring could crack the windshield.
Do not allow the wiper arms to contact
the windshield glass without a wiper
blade inserted.
Make certain that the wiper blades are
properly installed. Improperly installed
wiper blades may cause windshield
damage.
For your convenience, we recommend
that you have this work carried out by
an authorized Mercedes-Benz Center.