power steering MERCEDES-BENZ C300 2008 W204 Owner's Manual

Contents
Controls in detail............................... 69
Locking and unlocking ......................... 70
SmartKey ....................................... 70
SmartKey with KEYLESS-GO*
(Canada only) ................................. 73
Checking batteries in the SmartKey
or SmartKey with KEYLESS-GO*
(Canada only) ................................. 78
Loss of the SmartKey or SmartKey
with KEYLESS-GO* (Canada only) .. 79
Opening doors from the inside ....... 79
Automatic central locking .............. 80
Locking and unlocking
from the inside ............................... 81
Starter switch positions ....................... 82
SmartKey ....................................... 82
SmartKey with KEYLESS-GO*
(Canada only) ................................. 83
Seats.................................................... 85
Seat adjustment ............................. 85
Lumbar support .............................. 91
Seat heating* ................................. 91Steering wheel ..................................... 93
Steering wheel adjustment,
manual ........................................... 93
Steering wheel adjustment,
electrical* (Canada only)................ 94
Easy-entry/exit feature*
(Canada only) ................................. 95
Mirrors ................................................. 97
Interior rear view mirror ................. 97
Exterior rear view mirrors............... 97
Power folding
exterior rear view mirrors* ............. 98
Interior rear view mirror,
antiglare position ........................... 99
Auto-dimming rear view mirrors* . 100
Activating exterior rear view mirror
parking position* (Canada only)... 101
Memory function* (Canada only) ....... 102
Storing positions into memory* ... 103
Recalling positions from memory* 103
Storing exterior rear
view mirror parking position*....... 104
Fastening the seat belts .................... 105
Proper use of seat belts ............... 106
Seat belt height adjustment ......... 107Lighting ............................................. 108
Exterior lamp switch .................... 108
Switching on high beams ............. 112
Headlamp cleaning system* ........ 112
Corner-illuminating front
fog lamps* (With Bi-Xenon*
headlamps only)........................... 112
Hazard warning flasher ................ 114
Interior lighting ............................ 114
Door entry lamps ......................... 116
Trunk lamp ................................... 116
Windshield wipers ............................. 117
Switching on/off
windshield wipers ........................ 118
Single wipe .................................. 118
Intermittent wiping ...................... 118
Wiping with
windshield washer fluid................ 119
Power windows ................................. 120
Opening and closing
power windows ............................ 120
Summer opening feature ............. 123
Convenience closing feature ........ 124

60 Safety and Security
Driving safety systems
Continuous, steady brake pedal pressure
yields the advantages provided by the ABS,
namely braking power and the ability to
steer the vehicle.
The pulsating brake pedal can be an indica-
tion of hazardous road conditions and
functions as a reminder to take extra care
while driving.
Emergency brake maneuver
Keep continuous full pressure on the
brake pedal.
For more information, see “Practical hints”
(
page 374).
Adaptive Brake
Adaptive Brake provides a high level of
braking safety as well as increased braking
comfort. It is coupled with ABS, ESP
® and
BAS. Adaptive Brake takes driver and vehi-
cle characteristics into consideration, thus
achieving an optimal braking effect.
BAS
The Brake Assist System (BAS) operates in
emergency situations. If you apply the
brakes very quickly, the BAS automatically
provides full brake boost, thereby poten-
tially reducing the braking distance.
Apply continuous full braking pressure
until the emergency braking situation is
over.
The ABS will prevent the wheels from
locking.
When you release the brake pedal, the
brakes function again as normal. The BAS
is then deactivated.
Warning!G
When the ABS is malfunctioning, the BAS
EBP, ESP® and hill start assist are also
switched off.
When the ABS is malfunctioning, the wheels
may lock during hard braking, reducing
steering capability and extending the brak-
ing distance.
Warning!G
The ABS cannot prevent the natural laws of
physics from acting on the vehicle, nor can
it increase braking or steering efficiency
beyond that afforded by the condition of the
vehicle brakes and tires or the traction
afforded. The ABS cannot prevent acci-
dents, including those resulting from exces-
sive speed in turns, following another
vehicle too closely, or hydroplaning.
Only a safe, attentive, and skillful driver can
prevent accidents.
The capabilities of an ABS equipped vehicle
must never be exploited in a reckless or dan-
gerous manner which could jeopardize the
user’s safety or the safety of others.


69 Controls in detail
Locking and unlocking
Starter switch positions
Seats
Steering wheel
Mirrors
Memory function* (Canada only)
Fastening the seat belts
Lighting
Windshield wipers
Power windows
Driving and parking
Manual transmission
Automatic transmission*Instrument cluster
Control system
Audio system
Driving systems
Air vents
Dual-zone automatic climate con-
trol
3-zone automatic climate control*
(Canada only)
Trunk
Power tilt/sliding sunroof
Panorama roof with power
tilt/sliding panel*
Loading and storing
Useful features

82 Controls in detail
Starter switch positions
SmartKey
Starter switch
0For removing SmartKey1Power supply for some electrical con-
sumers, such as seat adjustment
2Ignition (power supply for all electrical
consumers) and driving position.
All lamps (except high beam headlamp
indicator lamp and turn signal indicator
lamps unless activated) in the instru-
ment cluster come on. If a lamp in the
instrument cluster fails to come on
when the ignition is switched on, have
it checked and replaced if necessary.
If a lamp in the instrument cluster re-
mains on after starting the engine or
comes on while driving, refer to “Lamps
in instrument cluster” (
page 374).
3Starting position
For information on starting the engine us-
ing the SmartKey, see “Starting: Make sure
the gear selector lever is set to P.”
(
page 127).
Warning!G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.
iWhen you switch on the ignition, the
indicator and warning lamps (except high beam
headlamp indicator lamp and turn signal indica-
tor lamps unless activated) in the instrument
cluster come on. The indicator and warning
lamps (except high beam headlamp indicator
lamp and turn signal indicator lamps if activated)
should go out when the engine is running. This in-
dicates that the respective systems are opera-
tional.
iVehicles with automatic transmission*: The
SmartKey can only be removed from the starter
switch with the gear selector lever in positionP.
iIf the SmartKey is left in starter switch
position0 for an extended period of time, it can
no longer be turned in the switch. In this case,
the steering is locked. To unlock, remove
SmartKey from starter switch and reinsert.
!If the SmartKey cannot be turned in the
starter switch, the battery may not be sufficient-
ly charged.

Check the battery and charge it if necessary
(
page 446).

Get a jump start (page 451).
To prevent accelerated battery discharge or a
completely discharged battery, always remove
the SmartKey from the starter switch when the
engine is not in operation.

85 Controls in detail
Seats
Seats
Seat adjustment
Warning!G
All seat, head restraint adjustments, as well
as fastening of seat belts, must be done be-
fore the vehicle is put into motion.
Warning!G
Do not adjust the driver’s seat while driving.
Adjusting the seat while driving could cause
the driver to lose control of the vehicle.
Never ride in a moving vehicle with the seat
back in an excessively reclined position as
this can be dangerous. You could slide un-
der the seat belt in a collision. If you slide
under it, the seat belt would apply force at
the abdomen or neck. That could cause se-
rious or fatal injuries. The seat backrest and
seat belts provide the best restraint when
the wearer is in a position that is as upright
as possible and seat belts are properly posi-
tioned on the body.
Your seat must be adjusted so that you can
correctly fasten your seat belt.
Observe the following points:

Adjust the seat backrest until your arms
are slightly angled when holding the
steering wheel.

Adjust the seat to a comfortable seating
position that still allows you to reach the
accelerator/brake pedal safely. The po-
sition should be as far back as possible
with the driver still able to properly oper-
ate controls.

Adjust the head restraint so that it is as
close to the head as possible and the
center of the head restraint supports
the back of the head at eye level.

Never place hands under the seat or
near any moving parts while a seat is be-
ing adjusted.
Failure to do so could result in an accident
and/or serious personal injury.
Warning!G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle.
Even with the SmartKey or SmartKey with
KEYLESS-GO* (Canada only) removed from
the starter switch or the SmartKey with
KEYLESS-GO* (Canada only) removed from
the vehicle, the power seats can be
operated.
Therefore, do not leave children unattended
in the vehicle, or with access to an unlocked
vehicle. A child’s unsupervised access to a
vehicle could result in an accident and/or
serious personal injury.

86 Controls in detail
Seats
For additional information about children
in the vehicle, see “Children in the vehicle”
(
page 51).Power seat adjustment
The seat adjustment switch is located on
the entry side of each front seat base.
The seat adjustment switch for Canada ve-
hicles with memory function* are located
on the front doors.
1Seat cushion tilt
2Seat height
3Seat fore and aft
4Seat backrest tilt
Vehicles without memory function*:
Adjust the head restraint height manu-
ally (
page 87).
Driver’s door (Canada only)
1Seat cushion tilt
2Seat height
3Seat fore and aft
4Seat backrest tilt
5Head restraint height (
page 87)
Warning!G
According to accident statistics, children
are safer when properly restrained in the
rear seating positions than in the front seat-
ing position. Thus, we strongly recommend
that children be placed in the rear seats
whenever possible. Regardless of seating
position, children 12 years old and under
must be seated and properly secured in an
appropriately sized infant restraint, toddler
restraint, or booster seat recommended for
the size and weight of the child.
A child’s risk of serious or fatal injuries is
significantly increased if the child restraints
are not properly secured in the vehicle and
the child is not properly secured in the child
restraint.
iAfter unlocking the vehicle or turning off the
engine, the seat adjustment can be operated for
up to approximately 3 minutes with the
SmartKey or KEYLESS-GO* (Canada only) in
starter switch position0 or removed from the
starter switch.
Vehicles with memory function* (Canada only):
The memory function* is operational at any time.
Seat and steering wheel adjustment is always
possible.

98 Controls in detail
Mirrors
Power folding exterior rear view
mirrors*
Folding exterior rear view mirrors in
and out manually
The exterior rear view mirrors can vibrate if
they are not folded out completely.
1Folds the exterior mirrors in and out
Switch on the ignition.
Folding in: Press button1.
Folding out: Press button1 again.
!If an exterior rear view mirror housing is
forcibly pushed forward (hit from the rear) or
forcibly pushed rearward (hit from the front), re-
position it by applying firm pressure until it snaps
back into place. The mirror housing is then prop-
erly positioned and you can adjust the mirror in
the usual manner.
iAt low ambient temperatures, the exterior
rear view mirrors will be heated automatically.
iCanada only:
The memory function* (
page 102) lets you
store the setting for the exterior rear view mir-
rors together with the setting for the steering
wheel and the seat positions.
!Before driving the vehicle through an auto-
matic car wash, fold the exterior mirrors in. Oth-
erwise they may get damaged.
!If an exterior rear view mirror housing is
forcibly pushed forward (hit from the rear), repo-
sition it manually by applying firm pressure until
it snaps back into place.
If an exterior rear view mirror housing is forcibly
pushed rearward (hit from the front), press
button1 to fold mirrors in, then press
button1 again to fold mirrors out. Do not force
mirrors by hand as this may damage the
adjustment mechanism.
The mirror housing is then properly positioned
and you can adjust the mirror in the usual
manner.


103 Controls in detail
Memory function* (Canada only)
MMemory button
1 2 3Memory position buttons
Storing positions into memory*
Adjust the seat (page 85) to the de-
sired position.
On the driver’s side: Adjust the steering
wheel (
page 93) and the exterior rear
view mirrors (
page 97) to the desired
position.
Press memory buttonM.
Release memory buttonM and press
one of the memory position buttons
within 3 seconds.
An acoustic signal sounds to confirm.
The settings are stored with the select-
ed position.
Recalling positions from memory*
Press and hold memory position
button until the seat, steering wheel
and exterior rear view mirrors have
completely moved to the stored
positions.
iThe memory function* is operational at any
time. Seat and steering wheel adjustment is al-
ways possible.
!Do not operate the power seats using the
memory position button if the seat backrest is in
an excessively reclined position. Doing so could
cause damage to front or rear seats.
First move seat backrest to an upright position.
iReleasing the memory position button
immediately stops movement to the stored
positions.

133 Controls in detail
Driving and parking
Parking
1Release handle
2Parking brake pedal
Warning!G
With the engine not running, there is no
power assistance for the brake and the
steering systems. In this case, it is impor-
tant to keep in mind that a considerably
higher degree of effort is necessary to brake
and steer the vehicle.
Warning!G
Do not park this vehicle in areas where com-
bustible materials such as grass, hay, or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
To reduce the risk of personal injury as a re-
sult of vehicle movement, before turning off
the engine and leaving the vehicle always:

Keep right foot on brake pedal.

Manual transmission: Move the gear-
shift lever into neutral position (no gear
is selected).

Firmly depress parking brake pedal.

Manual transmission: Move the gear-
shift lever into first or reverse gear.

Automatic transmission*: Move the
gear selector lever to positionP.

Slowly release brake pedal.

When parked on an incline, turn front
wheels towards the road curb.

Turn the SmartKey to starter switch
position0 and remove, or press
KEYLESS-GO* start/stop button
(
page 84).

Take the SmartKey or the SmartKey with
KEYLESS-GO* with you and lock vehicle
when leaving.
Warning!G
Engaging the parking brake while the vehicle
is in motion can cause the rear wheels to
lock up. You could lose control of the vehicle
and cause an accident. In addition, the
vehicle’s brake lights do not light up when
the parking brake is engaged.


135 Controls in detail
Driving and parking
SmartKey
Turning off: Turn the SmartKey in the
starter switch to position0 and remove
it.
The immobilizer is activated. KEYLESS-GO* (Canada only)
Turning off: Press the KEYLESS-GO
start/stop button to turn off the en-
gine.
With the driver’s door closed, the start-
er switch is now in position1. With the
driver’s door opened, the starter switch
is set to position0, same as SmartKey
removed from starter switch.
Releasing seat belts
Press the seat belt release button
(
page 106).
Allow the retractor to completely re-
wind the seat belt by guiding the latch
plate.
Warning!G
Do not turn off the engine before the vehicle
has come to a complete stop. With the en-
gine not running, there is no power assis-
tance for the brake and steering systems. In
this case, it is important to keep in mind that
a considerably higher degree of effort is nec-
essary to brake and steer the vehicle.
iIn an emergency you can turn off the engine
while driving by pressing and holding the
KEYLESS-GO start/ stop button for approxi-
mately 3 seconds.
!Make sure the seat belt retracts fully so that
the seat belt and/or latch plate cannot get
caught or pinched in the door or in the seat
mechanism. This can damage the seat belt and
impair the effectiveness of the seat belt, and/or
cause damage to the door and/or door trim pan-
el. Such damage is not covered by the
Mercedes-Benz Limited Warranty.
Damaged seat belts must be replaced. Contact
an authorized Mercedes-Benz Center.