radio controls MERCEDES-BENZ C300 SPORT 2008 W204 Owner's Guide

196 Controls in detail
Audio system
Switching to radio mode
Press buttonb on audio control
unit.
The radio basic menu appears in the
audio display once you have switched
to radio mode. You will hear the
station/channel last tuned in the previ-
ously selected waveband, provided
that the station/channel can be re-
ceived.
Illustration: radio mode in FM waveband
1Status line
2Station name
3Store position of station
4Main area with wavebandInformation displayed in the status line
(example)
The following information is displayed in
the status line:

Time (04:38)

Station name (WNYC)
Mobile phone readiness is indicated by
additional information being shown:

Mobile phone network signal
strengthI

Receiver symbol 4 ö.Calling up wavebands
You can choose from among the FM, AM
and WB wavebands and then request the
Sat mode*. Pressing again will switch back
to FM radio mode.
Press buttonb on audio control
unit repeatedly until desired waveband
has been selected.
The FM, AM, and WB wavebands and
the satellite radio* mode are called up
one after another.
The waveband currently selected
appears in the status line of the audio
display. The last selected station in the
selected waveband is heard.
iStation names 3, available for the FM
waveband, can only be seen when the station
transmits a name.
In the WB waveband, the audio system displays
the channel number, e. g. Channel 6, instead of
the station names and/or frequency.
WavebandFrequency
WB (Weather Band)Weather channels
FM87.7......107.9 MHz
AM530.......1 710 KHz

198 Controls in detail
Audio system
Tuning to a station by entering the fre-
quency manually
b
Radio
Enter Frequency
The menu for manual frequency entry
appears.
or
Press buttonó, on the keypad in
audio control unit briefly.
Enter frequency with keypad:
Enter desired frequency with
buttons1to R, with the keypad
in audio control unit briefly.
The audio system tunes in to the fre-
quency entered.
Exiting menu without making an en-
try: Press button í in the center
console (
page 184).Storing stations
You can store ten AM and ten FM stations
in the memory.
Storing stations manually with keypad
Tune in desired station.
Basic menu is shown in the audio
display.
Press and hold desired station
button1 to R until a brief signal
tone sounds.
The station is stored.
iThis function is not available for Weather
Band.
iIt is not possible to enter a frequency in the
respective waveband which is outside the fre-
quency range.
iIf you select a memory preset which is al-
ready in use, it will be overwritten by the new
station.

200 Controls in detail
Audio system
Satellite radio*
Submenu overview
Warning!G
Please devote your attention first and fore-
most to the traffic situation you are in.
Before your journey, please familiarize your-
self with the radio functions.
Only use the audio system when road and
traffic conditions permit you to do so. Other-
wise you could be involved in an accident in
which you or others could be injured.
iThe components and operating principles of
the audio system can be found on (
page 187).
Sat Presets Info Category Sound
Channel ListStation presets Show program infoAll channelsTreble
Channel Entry Select categoryBass
ServiceBalance/Fader
Surround sound*

201 Controls in detail
Audio system
Satellite radio
SIRIUS Satellite Radio provides over
130 channels of digital-quality radio, in-
cluding 100% commercial-free music,
sports, news and entertainment. SIRIUS
Satellite Radio uses a fleet of high-orbit
satellites to broadcast 24 hours per day,
coast to coast, in the contiguous U.S. and
Canada.
This diverse, satellite-delivered program-
ming is available for a monthly subscrip-
tion fee.
For more information and service availabil-
ity call the SIRIUS Service Center
(
page 207) (1-888-539-7474), or con-
tact

www.sirius.com (USA)

www.siriuscanada.com (Canada)Subscribing to satellite radio
Press buttonb on audio control
unit repeatedly until satellite radio Sat
is selected.
The following options are possible:

Satellite radio service is not
activated

Satellite radio service is fully
activated
iAdditional satellite radio equipment and a
subscription to SIRIUS Satellite Radio service
provider are required for the satellite radio oper-
ation described in this chapter.
Contact an authorized Mercedes-Benz Center
for details and availability for your vehicle.
iNote that categories and channels shown in
illustrations are dependent on programming con-
tent delivered by the service provider. Program-
ming content is subject to change. Therefore,
channels and categories shown in illustrations
and descriptions contained in this manual may
differ from the channels and categories
delivered by the service provider.
iSatellite radio service may be unavailable or
interrupted from time to time for a variety of rea-
sons, such as environmental or topographic con-
ditions and other things we can’t control. Service
might also not be available in certain places
(e.g., in tunnels, parking garages, or within or
next to buildings) or near other technologies. In
such situations, the satellite radio’s main menu
shows the “Acquiring signal...” screen. At this
point, the radio’s functions are restricted and the
service info display (
page 207) appears.
iIf a satellite receiver is not installed or not
properly installed:
The message
Device unavailable will ap-
pear.
If the satellite radio service is not activated, the
“SIRIUS Preview” display appears.

202 Controls in detail
Audio system
Satellite radio service is not activated
The telephone number of the SIRIUS Ser-
vice Center and the twelve-digit electronic
serial number (SIRIUS-ID) of the particular
receiver are required when calling the
SIRIUS Service Center for an activation re-
quest.
b
Sat
Service.
Closing screen: Press n.
To activate satellite radio service:
Contact satellite radio service provider
at the telephone number displayed in
the service display.
After the connection is made:
Follow the instructions given by the op-
erator.The activation process may take up to
10 minutes. If it is successful, you will
see the display with the message
Acquiring Signal... followed by the
satellite radio basic menu.Satellite radio service is activated
The basic satellite radio menu appears.
You will hear the channel last tuned in, pro-
vided that it can be received.
Switching on
For important subscription information see
“Subscribing to satellite radio”
(
page 201).
Press buttonb on audio control
unit repeatedly until satellite radio Sat
is selected.
The message
Acquiring Signal... will
appear when the signal is not available.
After the audio system acquires the
signal, the satellite radio basic menu
will appear. The station last tuned to
will begin to play.
iActivating the satellite radio service might
not be available in certain places (e.g., in tun-
nels, parking garages, or within or next to build-
ings). If a subscription is not included with
system purchase, credit card information is re-
quired to activate your account.
The activation process takes approximately 5 to
10 minutes after calling the SIRIUS Service Cen-
ter.
If a satellite receiver is not installed or not prop-
erly installed:
The message
Device unavailable will ap-
pear.
iIt is also possible to activate the satellite ra-
dio service online. To do so please visit SIRIUS
Satellite Radio's website at www.sirius.com
(USA) or www.siriuscanada.com (Canada).

203 Controls in detail
Audio system
Main satellite radio menu
1Main area with channel display
2Selected program category
3Number of selected channel
4Selected channel
5Sound settings
6To select program category
7Current artist and title
8Channel information
9Preset options
aSatellite radio optionsSelecting program category
Satellite radio channels are split up into
categories such as News, Sports News, or
Country Music, if available. The category
list is sorted alphabetically.
Call up category list: b
Cat.
or
Slideomp or rotate ymz until Cat is
highlighted.The category list appears.
Select a category: Slideqmr or ro-
tate ymz.
Set the selected category: Press n.
The selected program category (alpha-
betical order) will appear in the audio
display. The channel last tuned in the
new category will begin to play.
When searching, tuning in, or selecting
from the channel list, the “All Chan-
nels” option accesses all of your sub-
scribed channels.
iMain area 1 can show all channels includ-
ed in your subscription. Which channels are
shown depends on the selected program
category4.
Note that categories and channels shown in illus-
trations are dependent on programming content
delivered by the service provider. Programming
content is subject to change.
Therefore, channel and categories shown in illus-
trations and descriptions contained in this man-
ual may differ from the channels and categories
delivered by the service provider.
iThe channels are categorized. Categories al-
low you to tune to stations broadcasting a cer-
tain type of program.
iWhen you select the category “All Chan-
nels”, you have access to all the channels you
subscribe to, regardless of category.

205 Controls in detail
Audio system
Channel number is valid, but channel is
not included in subscription: The mes-
sage
Please call SIRIUS to subscribe
pops up (
page 202).
Press n to close the message in the
audio display.
Tuning in channels using the satellite ra-
dio channel list
b
Sat
Channel List.
The channel list appears. The dotR in
front of a list entry indicates the cur-
rently selected channel.
Select channel by rotating ymz or
slidingqmr.
Press n to confirm.Tuning in channels using satellite radio
channel presets
b
Presets.
or
Press n when the main area is select-
ed.
The preset menu appears. The dotR
in front of a preset position indicates
that this is the channel currently select-
ed and being listened to.
Select station in memory by rotating
ymz or sliding qmr.
Press n to confirm.
or
Press desired station button1 to
R, with the keypad in audio control
unit briefly.
The audio system tunes in the correspond-
ing channel as long as it is included in your
subscription and is still available.
If the channel is not included in your sub-
scription, you will see the message de-
scribed in the section “Satellite radio
service is not activated” (
page 202).
If the channel is no longer available, you
will see the message
Invalid Channel.
Closing message: Press n.iThe contents of the channel list depends on
which channels are included in your subscription
and which program category you have selected
(
page 203). If only the preview channel is acti-
vated, the channel list contains only the preview
channel.

207 Controls in detail
Audio system
Calling SIRIUS Service Center
b
Sat
Service.
The telephone number of the SIRIUS
Service Center and the twelve-digit
electronic serial number (SIRIUS-ID) of
the particular receiver are displayed.
Closing screen: Slide omp or
pressn.Channel update
The service provider may conduct a chan-
nel update.
During the update, the message
Updating
channels...
will appear on the audio dis-
play.
The channel last tuned will be muted until
the update is completed. You cannot oper-
ated the satellite radio during the update.
After completion of the update, the satel-
lite radio basic menu will appear. The sta-
tion last tuned to will begin to play. If not
available, the next subscribed channel
starts beginning with channel 1. Sound settings
For sound adjusting see:

Volume (page 189)

Balance control and fader
(
page 190)

Bass and treble control (page 189)

Surround sound* (page 190)
iIt may be necessary to call the SIRIUS Ser-
vice Center if, for example:

You want to cancel the subscription or
re-subscribe at a later date.

You forget to pay the bill.

You sell the car to another person.

222 Controls in detail
Audio system
Telephone*
Safety precautionsWhen the telephone is connected via the
Bluetooth® interface to the audio system,
you can operate the telephone using the
following devices:

audio system (page 237)

Audio controller

Audio control unit

buttonss andt on the multi-
function steering wheel (
page 152)

mobile phone keypad
Please note that these functions are only
available with Mercedes-Benz approved
telephones.
Warning!G
Some jurisdictions prohibit the driver from
using a cellular telephone while driving.
Whether or not prohibited by law, for safety
reasons, the driver should not use the cellu-
lar telephone while the vehicle is in motion.
Stop the vehicle in a safe location before
placing or answering a call.
If you nonetheless choose to use the tele-
phone
1 while driving, please use the hands-
free device and be sure to pay attention to
the traffic situation at all times. Use the tele-
phone only when road, weather and traffic
conditions permit. Otherwise, you may not
be able to observe traffic conditions and
could endanger yourself and others.
1Observe all legal requirements.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approxi-
mately 14 m) every second.
Warning!G
Never operate radio transmitters equipped
with a built-in or attached antenna (i.e. with-
out being connected to an external antenna)
from inside the vehicle while the engine is
running. Doing so could lead to a malfunc-
tion of the vehicle’s electronic system, pos-
sibly resulting in an accident and/or
personal injury.
iThe functions and services available to you
while using the telephone depend on your ser-
vice provider and the type of telephone you are
using. See also separate operating manual for in-
structions on how to use your telephone.

305 Controls in detail
Useful features
Step 7:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:
Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the “training” button may also be referred
to as “learn”or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
operator’s manual.
Step 9:
Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing two steps.
Step 10:
Return to the vehicle and firmly press,
hold for 2 seconds and release the pro-
grammed signal transmitter button
(2, 3 or4).
Step 11:
Press, hold for 2 seconds and release
same signal transmitter button a sec-
ond time to complete the training pro-
cess.Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
iIf indicator lamp1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.iSome garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to com-
plete the training process.