engine MERCEDES-BENZ C300 SPORT 2008 W204 Owner's Guide

112 Controls in detail
Lighting
Switching on high beams
Combination switch
1High beam
2High beam flasher
High beam: Turn the exterior lamp
switch to positionB (
page 108).
Push the combination switch in the di-
rection of arrow1.
The high beam indicatorA in the in-
strument cluster comes on
(
page 26).
High beam flasher: Pull the combina-
tion switch briefly in the direction of
arrow2.
Headlamp cleaning system*
The headlamps are automatically cleaned
with a high-pressure water jet when, at the
same time,

the engine is running

the headlamps are switched on

the windshield wipers have wiped the
windshield with washer fluid for the
first time.
The headlamps are cleaned every tenth
time the windshield is washed with washer
fluid.
When you switch off the headlamps or the
ignition, the automatic function is reset
and will start counting the next time from
the beginning.
For information on filling up the washer
reservoir, see “Windshield washer system
and headlamp cleaning system*”
(
page 330).Corner-illuminating front fog lamps*
(With Bi-Xenon* headlamps only)
The corner-illuminating front fog lamps
improve illumination of the area in the
direction into which you are turning.
The corner-illuminating front fog lamps will
operate with the engine running and with:

the exterior lamp switch in
positionB or* (
page 108)
or

the daytime running lamp mode acti-
vated (
page 110).
iThe corner-illuminating front fog lamps will
only come on in low ambient lighting conditions.
iIf you are driving faster than 25 mph
(40 km/h) or have the front fog lamps switched
on, the corner-illuminating front fog lamps
function is not available.

115 Controls in detail
Lighting
Automatic control
Deactivating: Press button2.
The button engages when pressed in.
Automatic control of the interior light-
ing is deactivated.
The interior lighting remains switched
off in darkness, even when you:

unlock the vehicle

open a door

remove the SmartKey from the
starter switch
Activating: Press button2 again.
The button returns to its original posi-
tion and sits flush with the other but-
tons. Automatic control of the interior
lighting is activated.
The interior lighting switches on in
darkness, when you:

unlock the vehicle

open a door

remove the SmartKey from the
starter switch
The interior lighting switches off
automatically.
You can set whether the interior light-
ing should come on when you remove
the key from the starter switch via the
control system, see “Setting interior
lighting delayed shut-off”
(
page 173).Manual control
Switching on/off front interior light-
ing: Press button4.
Switching on/off rear interior light-
ing: Press button 1.
Switching on/off front reading
lamps: Press button 3 or 5.
The left and right front reading lamps
are located in the lower edge of the in-
terior rear view mirror.
!An interior lamp switched on manually does
not go out automatically.
Leaving an interior light switch in the ON position
for extended periods of time with the engine
turned off could result in a discharged battery.
iThe interior lighting is factory-set to auto-
matic mode.
iIf the door remains open, the interior lighting
switches off automatically after approximately
5minutes.

117 Controls in detail
Windshield wipers
Windshield wipers
Combination switch
1Switching on windshield wipers
2Single wipe
Wiping with windshield washer fluid
Switch on the ignition.
!If the windshield wipers leave smears on the
windshield after the car has been driven through
an automatic car wash, then wax or other resi-
due is on the windshield. Shortly after washing
the car in an automatic car wash, clean the wind-
shield with windshield washer fluid.
!Do not operate the windshield wipers when
the windshield is dry. Dust that accumulates on
a windshield might scratch the glass and/or
damage the wiper blades when wiping occurs on
a dry windshield. If it is necessary to operate the
windshield wipers in dry weather conditions, al-
ways operate the windshield wipers with wind-
shield washer fluid.
!If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off immediate-
ly.

For safety reasons, stop the vehicle in a safe
location and,

remove the SmartKey from starter
switch
or

turn off the engine by pressing the
KEYLESS-GO* start/stop button and
open the driver’s door (with the driver’s
door open, starter switch is in
position0, same as with SmartKey re-
moved from starter switch)

engage the parking brake
before attempting to remove any blockage.

Remove blockage.

Turn the windshield wipers on again.
If the windshield wipers fail to function at all in
combination switch position U or V,

set the combination switch to the next
higher wiper speed

have the windshield wipers checked at the
nearest authorized Mercedes-Benz Center

119 Controls in detail
Windshield wipers
Turn the combination switch to posi-
tion U or V.
Intermittent wiping starts with selected
wiping interval.
Vehicles with rain sensor*:
After the initial wipe, pauses between
wipes are automatically controlled by
the rain sensor.
Intermittent wiping interval is depen-
dent on wetness of windshield.Wiping with windshield washer fluid
Press the combination switch in the di-
rection of arrow2 (
page 117) past
the resistance point.
The windshield wiper operates with
washer fluid.
For information on filling up the washer
reservoir, see “Windshield washer system
and headlamp cleaning system*”
(
page 330).
iIntermittent wiping is interrupted when the
vehicle is at a standstill and a front door is
opened. This protects persons getting into or out
of the vehicle from being sprayed.
Intermittent wiping will be continued when

all doors are closed
and

the clutch pedal is depressed (vehicles with
manual transmission
or

the gear selector lever is positionD orR (ve-
hicles with automatic transmission*)
or

the wiper setting is changed using the com-
bination switch
iTo prevent smears on the windshield or
noisy/chattering wiper blades, wipe with wind-
shield washer fluid every now and then even
when it is raining.
iVehicles with headlamp cleaning system*:
The headlamp cleaning system* will clean the
headlamps automatically after the first and every
tenth time windshield washer fluid is used while
the engine is running (
page 112).

126 Controls in detail
Driving and parking
Starting the engine Manual transmission
Gearshift pattern for manual transmission
For more information, see “Manual trans-
mission” (
page 136).
Warning!G
Make sure absolutely no objects are ob-
structing the pedals’ range of movement.
Keep the driver’s footwell clear of all obsta-
cles. If there are any floormats or carpets in
the footwell, make sure the pedals still have
sufficient clearance.
During sudden driving or braking maneuvers
the objects could get caught between the
pedals. You could then no longer brake or
accelerate. This could lead to accidents and
injury.Warning!G
Inhalation of exhaust gas is hazardous to
your health. All exhaust gas contains carbon
monoxide (CO), and inhaling it can cause un-
consciousness and possible death.
Do not run the engine in confined areas
(such as a garage) which are not properly
ventilated. If you think that exhaust gas
fumes are entering the vehicle while driving,
have the cause determined and corrected
immediately. If you must drive under these
conditions, drive with at least one window
fully open.

127 Controls in detail
Driving and parking
Starting: Depress brake pedal.
Make sure the gearshift lever is in
neutral position (no gear selected).
Fully depress clutch pedal.
Otherwise the engine cannot be
started due to the integrated safety
interlock.
Do not depress the accelerator.
Turn the SmartKey in the starter switch
to position3 and hold until the engine
starts.
For information on turning off the engine,
see “Turning off the engine” (
page 134).Automatic transmission*
Gearshift pattern for automatic
transmission
PPark position
RReverse gear
NNeutral
DDrive position
For more information on how to operate
the gear selector lever, see “Automatic
transmission*” (
page 127).SmartKey
Starting: Make sure the gear selector
lever is set toP.
Do not depress the accelerator.
Turn the SmartKey in the starter switch
to position3 and hold until the engine
starts.
For information on turning off the engine
with the SmartKey, see “Turning off the en-
gine” (
page 134).
iYou can also use the “touch-start” function.
Turn the SmartKey to position 3 and release it
again immediately. The engine then starts
automatically.
iYou can also start the engine with the auto-
matic transmission set to N.

128 Controls in detail
Driving and parking
KEYLESS-GO* (Canada only)
You can start your vehicle without the
SmartKey in the starter switch using the
KEYLESS-GO start/stop button on the
starter switch.
The SmartKey with KEYLESS-GO must be
located in the vehicle.1KEYLESS-GO* start/stop button
(Canada only)
Starting: Make sure KEYLESS-GO
start/stop button is inserted in the
starter switch (
page 83).
Make sure the gear selector lever is set
toP.
Depress the brake pedal during the
starting procedure.
Do not depress the accelerator.
Press KEYLESS-GO start/stop button
once.
The engine starts if the SmartKey with
KEYLESS-GO is in the vehicle.For information on turning off the engine
with KEYLESS-GO, see “Turning off the en-
gine” (
page 134).
Warning!G
As long as the SmartKey with KEYLESS-GO
is in your vehicle, the vehicle can be started.
Therefore, never leave children unattended
in the vehicle, as they could otherwise acci-
dentally start the engine.
When leaving the vehicle, always take the
SmartKey with KEYLESS-GO with you and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.
iYou can also start the engine with the auto-
matic transmission set to N.
iIf you wish to start the vehicle with the
SmartKey instead of the KEYLESS-GO feature,
remove the KEYLESS-GO start/stop button from
the starter switch and proceed as described in
“Starting with the SmartKey” (
page 127).

129 Controls in detail
Driving and parking
Starting difficulties
The engine does not start. You can hear
the starter.
There could be a malfunction

in the engine electronics, or

in the fuel supply system
Carry out the following steps:
If you are starting the engine with the
SmartKey: Turn SmartKey in starter
switch to position0 and repeat starting
procedure (
page 126).
If you are starting the engine with
KEYLESS-GO*: Close any doors that
may be open to allow for better detec-
tion of the SmartKey with
KEYLESS-GO*.
or
Remove the KEYLESS-GO* start/stop
button from starter switch.
Start the engine with the SmartKey as
radio signals from another source may
be interfering with the SmartKey with
KEYLESS-GO*.
Repeat the starting procedure
(
page 126).
If the engine does not start after several
starting attempts:
Call Roadside Assistance.
Notify an authorized Mercedes-Benz
Center.
The engine does not start. You cannot
hear the starter.
The battery may not be sufficiently
charged.
Get a jump start (page 451).
If the engine will not start despite a jump
start:
Call Roadside Assistance.
Notify an authorized Mercedes-Benz
Center.
Driving off
!Remember that extended starting attempts
can drain the battery.
Warning!G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
(Canada only) from the starter switch, take
it with you, and lock the vehicle. Do not
leave children unattended in the vehicle, or
with access to an unlocked vehicle. Children
could release the parking brake, which
could result in an accident and/or serious
personal injury.
Warning!G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of loss of control.

130 Controls in detail
Driving and parking
1Release handle
2Parking brake pedal
Release the parking brake by pulling on
release handle1.
The indicator lamp; (USA only)
or3 (Canada only) in the instru-
ment cluster goes out.Manual transmission
Fully depress the clutch pedal.
Move gearshift lever to first gear to
drive forward, or to reverse gear to
drive in reverse.
Release the brake pedal.
Simultaneously slowly release the
clutch pedal and carefully depress the
accelerator pedal.
!If you hear a warning signal, the red indica-
tor lamp 0 (USA only) or ! (Canada only)
in the instrument cluster flashes and the mes-
sage
Release Parking Brake appears in the
multifunction display when driving off, you have
forgotten to release the parking brake.
Release the parking brake.
iAt vehicle speeds of approximately 9 mph
(15 km/h), the automatic central locking system
engages and the locking knobs in the doors drop
down.
The automatic door lock feature can be deacti-
vated (
page 173).
You can open a locked door from the inside.
Open door only when conditions are safe to do
so.
!Simultaneously depressing the accelerator
pedal and applying the brakes reduces engine
performance and causes premature brake and
drivetrain wear.
!Do not run a cold engine at high engine
speeds as this may shorten its service life.
!In order to avoid damage to the transmis-
sion, place the gearshift lever to reverse gear
only when the vehicle is stopped.
!Shift gear in a timely manner and do not ex-
ceed the maximum permissible engine speed for
each gear.
Do not allow the wheels to spin as this could
damage the drive train.

131 Controls in detail
Driving and parking
Automatic transmission*
Depress the brake pedal.
The gear selector lever can now be
used.
Release the parking brake by pulling on
release handle1.
The indicator lamp; (USA only)
or3 (Canada only) in the instru-
ment cluster goes out.
Shift automatic transmission toD orR.
Release the brake pedal.
Carefully depress the accelerator
pedal.
After a cold start, the automatic transmis-
sion shifts at a higher engine revolution.
This allows the catalytic converter to reach
its operating temperature earlier.
For more information, see “Driving instruc-
tions” (
page 311).
Turn signals
Combination switch
1Turn signals, right
2Turn signals, left
Press the combination switch in the
direction of arrow1 or2.
The corresponding turn signal indicator
lampL orK in the instrument
cluster flashes (
page 26).
The combination switch resets automati-
cally after major steering wheel move-
ments.
Warning!G
It is dangerous to shift the gear selector le-
ver out of P or N if the engine speed is high-
er than idle speed. If your foot is not firmly
on the brake pedal, the vehicle could accel-
erate quickly forward or in reverse. You
could lose control of the vehicle and hit
someone or something. Only shift into gear
when the engine is idling normally and when
your right foot is firmly on the brake pedal.
iShifting from gear positionP to positionR,
N, or D is only possible with the brake pedal de-
pressed. Without the brake pedal depressed, the
gear selector lever can be moved, but the park-
ing pawl remains engaged, not allowing shifting
to occur.
iWait for the gear selection process to com-
plete before setting the vehicle in motion.
!Shift the automatic transmission toP orR
only when the vehicle is stopped in order to avoid
damaging the transmission.