jump start MERCEDES-BENZ C320 4MATIC WAGON 2003 S203 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2003, Model line: C320 4MATIC WAGON, Model: MERCEDES-BENZ C320 4MATIC WAGON 2003 S203Pages: 370, PDF Size: 11.49 MB
Page 25 of 370
31 Getting started
Unlocking
Starter switch positionsStarter switch0For removing key
The steering is locked when the key is
removed from the starter switch. If
necessary, move steering wheel slight-
ly to allow the locking mechanism to
engage.
1Power supply to some electrical con-
sumers, such as seat adjustment
2Ignition (power supply for all electrical
consumers) and driving position
3Starting position
Warning!
G
When leaving the vehicle, always remove the
SmartKey from the starter switch and lock
the vehicle. Do not leave children unattend-
ed in the vehicle, or with access to an un-
locked vehicle. Unsupervised use of vehicle
equipment may cause an accident and/or
serious personal injury.iVehicles with automatic transmission:
The SmartKey can only be removed
from the starter switch with the gear
selector lever in positionP.
!If the key is left in starter switch
position0 for an extended period of
time, it can no longer be turned in the
starter switch.
Remove the key from the starter
switch and reinsert.
If the key can still not be turned, the
battery may not be sufficiently
charged.
Check the battery and charge it if
necessary (
page 305)
Get a jump start (
page 308).
To prevent accelerated battery dis-
charge and a possible dead battery, al-
ways remove the key from the starter
switch.
S203 MY03_A.book Page 31 Tuesday, January 28, 2003 2:22 PM
Page 39 of 370
45 Getting started
Driving
Starting
Turn the key in the starter switch to
position3. Release only when the en-
gine is firing regularly (
page 31).
Depress the brake pedal.
The selector lever lock is released.
For information on turning off the engine
with the key, see “Turning off engine”
(
page 52).Starting difficulties
If the engine does not start as described,
carry out the following steps:
Turn key in starter to position0 and re-
peat starting procedure (
page 44).
Remember that extended starting at-
tempts can drain the battery.
Get a jump start (
page 308).If the engine does not start after several
starting attempts, there could be a mal-
function in the engine electronics or in the
fuel supply system.
Notify an authorized Mercedes-Benz
Center.
iYou can also use the “touch-start”
function. Turn the key to position3 and
release it again immediately. The en-
gine then starts automatically.
S203 MY03_A.book Page 45 Tuesday, January 28, 2003 2:22 PM
Page 208 of 370
214 Controls in detailUseful featuressystem mutes and the message
TELE AID
– ROADSIDE ASSISTANCE CALL ACTIVE
ap-
pears in the multifunction display.
Describe the nature of the need for as-
sistance.
The Mercedes-Benz Roadside assistance
dispatcher will either dispatch a qualified
Mercedes-Benz technician or arrange to
tow your vehicle to the nearest
Mercedes-Benz Center. For services such
as labor and/or towing, charges may ap-
ply. Refer to the Roadside Assistance man-
ual for more information.
These programs are only available in the
USA:
Sign and Drive services: Services such
as jump start, a few gallons of fuel or
the replacement of a flat tire with the
vehicle spare tire are obtainable.
Remote Vehicle Diagnostics: This func-
tion permits the Mercedes-Benz Road-
side Assistance dispatcher to
download malfunction codes and actu-
al vehicle data.Information button
¡
Located below the center armrest cover is
the Information button
¡
.
Press and hold the button (for longer
than 2 seconds).
A call to the Customer Assistance Cen-
ter will be initiated. The button will
flash while the call is in progress. The
message
INFO – CONNECTING CALL
will
appear in the multifunction display.
When the connection is established, the
message
INFO – CALL CONNECTED
appears
in the multifunction display. The Tele Aid
system will transmit data generating the
vehicle identification number, model, color
and location (subject to availability of cel-
lular and GPS signals).
A voice connection between the Customer
Assistance Center representative and the
occupants of the vehicle will be estab-
iThe indicator lamp in the Roadside As-
sistance button
•
remains illumi-
nated in red for approx. 10 seconds
during the system self-check after turn-
ing the key in the starter switch to
position2 (together with the SOS but-
ton and the Information button
¡
).
See system self-check (
page 211)
when the indicator lamp does not light
up in red or stays on longer than ap-
proximately 10 seconds.
If the indicator lamp in the Roadside
Assistance button
•
is illuminated
continuously and there was no voice
connection to the Response Center es-
tablished, then the Tele Aid system
could not initiate a Roadside Assis-
tance call (e.g. the relevant cellular
phone network is not available). The
message
ROADSIDE ASSISTANCE –
CALL FAILED
appears in the multifunc-
tion display.
Roadside Assistance calls can be ter-
minated using the
ì
button on the
multifunction steering wheel.
S203 MY03_A.book Page 214 Tuesday, January 28, 2003 2:22 PM
Page 247 of 370
253 Practical hints
What to do if …
Where will I find ...?
Unlocking/locking in an emergency
Opening/closing in an emergency
Replacing bulbs
Replacing wiper blades
Flat tire
Battery
Jump starting
Towing the vehicle
Fuses
S203 MY03_A.book Page 253 Tuesday, January 28, 2003 2:22 PM
Page 257 of 370
263 Practical hints
What to do if …
Display
Possible cause
Suggested solution
#
BATTERY/ALTERNATOR
VISIT WORKSHOP!
The battery was charged with a battery
charger or jump started.
Have the battery checked at a service
station.
The battery is no longer charging.
Possible causes:
alternator malfunctioning
broken poly-V-belt
Stop immediately and check the
poly-V-belt.
If it is broken:
Do not continue to drive. Otherwise
the engine will overheat due to an in-
operative water pump which may re-
sult in damage to the engine. Notify an
authorized Mercedes-Benz Center.
If it is intact:
Drive immediately to the nearest au-
thorized Mercedes-Benz Center.
3
(Canada only)
;
(USA only)
BRAKE PAD WEAR
VISIT WORKSHOP!
The brake pads have reached their wear lim-
it.
Have the brake pads replaced as soon
as possible.
!Brake pad thickness must be visually
checked by a qualified technician at the
intervals specified in the Service book-
let.
S203 MY03_A.book Page 263 Tuesday, January 28, 2003 2:22 PM
Page 299 of 370
305 Practical hints
Battery
Battery
The battery is located in the engine com-
partment on the right hand side.
Removal of filter box:
Release the three clamps1.
Remove filter box.
Installation of filter box:
Insert filter box properly.
Secure it with the three clamps1.
Warning!
G
Failure to follow these instructions can re-
sult in severe injury or death.
Never lean over batteries while connecting,
you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water and seek
medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking etc.
!Never loosen or detach battery termi-
nal clamps while the engine is running
or the key is in the starter switch. Oth-
erwise the alternator and other elec-
tronic components could be severely
damaged.
Have the battery checked regularly by
an authorized Mercedes-Benz Center.
Refer to Service Booklet for mainte-
nance intervals or contact your autho-
rized Mercedes-Benz Center for further
information.Warning!
G
Do not place metal objects on the battery as
this could result in a short circuit.
Use leak-proof battery only to avoid the risk
of acid burns in the event of an accident.
S203 MY03_A.book Page 305 Tuesday, January 28, 2003 2:22 PM
Page 302 of 370
308 Practical hintsJump starting
Jump starting
If the battery is discharged, the engine can
be started with jumper cables and the bat-
tery of another vehicle. Observe the follow-
ing:
Jump starting should only be performed
when the engine and catalytic convert-
er are cold.
Do not start the engine if the battery is
frozen. Let the battery thaw out first.
Only jump start from batteries with the
same voltage rating (12 V). Jump start-
ing with a more powerful battery could
damage the vehicle’s electrical system,
which will not be covered by the
Mercedes-Benz Limited Warranty.
Use only jumper cables with sufficient
cross-section and insulated terminal
clamps.
Always make sure that the jumper ca-
bles are not on or near pulleys, fans, or
other parts that move when the engine
is started or running.
Warning!
G
Failure to follow these directions will cause
damage to the electronic components, and
can lead to a battery explosion and severe
injury or death.
Never lean over batteries while connecting
or jump starting, you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water, and seek
medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and very explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking etc.
Read all instructions before proceeding.
!Jump starting may only be performed
on the battery installed in the engine
compartment.
Avoid repeated and lengthy starting at-
tempts.
Do not attempt to start the engine us-
ing a battery quick charge unit.
If engine does not run after several un-
successful starting attempts, have it
checked at the nearest authorized
Mercedes-Benz Center.
Excessive unburned fuel generated by
repeated failed starting attempts may
damage the catalytic converter and
may present a fire risk.
Make sure the jumper cables do not
have loose or missing insulation.
Make sure the cable clamps do not
touch any other metal part while the
other end is still attached to a battery.
S203 MY03_A.book Page 308 Tuesday, January 28, 2003 2:22 PM
Page 303 of 370
309 Practical hints
Jump starting
The battery is located in the engine com-
partment on the right hand side. The termi-
nals for jump starting are located in front
of the battery.
Make sure that the two vehicles do not
touch.
Turn off all electrical consumers.
Apply parking brake.
Shift selector lever to positionP (man-
ual transmission to Neutral).1Positive terminal of charged battery
2Positive under hood terminal in front of
discharged battery
3Negative terminal of charged battery
4Negative under hood terminal in front
of discharged battery
Connect positive terminal1 of the
charged battery with the under hood
terminal2 in front of the discharged
battery with the jumper cables. Clamp
cable to charged battery1 first.
Start engine of the vehicle with the
charged battery and run at idle speed.
Connect negative terminal3 of the
charged battery with the under hood
terminal4 in front of the discharged
battery with the jumper cables. Clamp
cable to charged battery3 first.
Start the engine of the disabled vehi-
cle.
Now you can again turn on the electrical
consumers. Do not turn on the lights under
any circumstances.
Remove the jumper cables first from
negative terminals3 and4 and then
from positive terminals1 and2.
Have the battery checked at the near-
est authorized Mercedes-Benz Center.
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 239).
!Vehicles with automatic transmission
or 4MATIC*:
Do not tow-start the vehicle.
S203 MY03_A.book Page 309 Tuesday, January 28, 2003 2:22 PM
Page 306 of 370
312 Practical hintsTowing the vehicleWarning!
G
With the engine not running, there is no
power assistance for the braking and steer-
ing systems. In this case, it is important to
keep in mind that a considerably higher
degree of effort is necessary to brake and
steer the vehicle. Adapt your driving accord-
ingly.
!When towing the vehicle with all wheels
on the ground, please note the follow-
ing:
With the automatic central locking
activated and the key in starter switch
position2, the vehicle doors lock if the
left front wheel as well as the right rear
wheel are turning at vehicle speeds of
approx. 9 mph (15 km/h) or more.
Switch off the tow-away alarm
(page 80).
To prevent the vehicle doors from
locking, deactivate the automatic
central locking (
page 88).
Towing of the vehicle should only be
done using the properly installed
towing eye bolt. Never attach tow
cable, tow rope or tow rod to vehicle
chassis, frame or suspension parts.
iIf the battery is disconnected or
discharged
the key will not turn in the starter
switch. See notes on the battery
(page 305) or on jump starting
(page 308).
the selector lever will remain
locked in positionP. See notes on
manual unlocking of gear selector
lever (
page 289).
S203 MY03_A.book Page 312 Tuesday, January 28, 2003 2:22 PM
Page 341 of 370
347 Index
Gear shifting malfunctions 140
Kickdown 140
Manual shifting 136
One-touch gearshifting 136
Program mode selector switch 139
Selector lever position 135
Starting with 44
Transmission fluid 237
Winter program mode 139
Auxiliary fuse box 315
B
BabySmart
TM
Airbag deactivation system 67
Compatible child seats 67
Self-test 67
BabySmart
TM airbag deactivation
system 339
BabySmartTM compatible child
seats 339
Backrest
Folding forward 199
Folding rearward 200
Backrest tilt 33
Backup lamps 293, 298
Bulbs 293BAS 75, 339
Messages in display 262
Batteries, electronic key
Checking 86
Batteries, SmartKey
Changing 287
Check lamp 85
Checking 86
Battery discharged
Jump starting 308
Battery, vehicle 239, 305
Charging 306
Disconnecting 306
Messages in display 278
Reconnecting 307
Reinstalling 306
Removing 306
Bi-Xenon headlamps* 339
Bi-Xenon type
Front lamp bulbs 295
Block heater 245
Blocking
Rear door window operation 71
Bolts
For Minispare wheel 284
For spare wheel 282Brake assist system (BAS) 339
Brake fluid 233, 330
Brake lamp bulbs 293
Brake lamp, high mounted 293
Brake pads
Message in display 263
Brakes 224
Break-in period 222
Bulbs, replacing 292
Additional turn signals 292
Backup lamps 293
Brake lamps 293
Fog lamps 292
Front lamps 292
High beam 292
High mounted brake lamp 293
License plate lamps 293, 298
Low beam 292
Parking lamps 292, 293, 295, 296
Rear fog lamp 293
Rear fog lamps 297
Side marker lamps 292, 297
Standing lamps 292, 293, 295, 296
Tail lamp assemblies 293, 297
Turn signal lamps 292, 293
S203 MY03_A.book Page 347 Tuesday, January 28, 2003 2:22 PM