MERCEDES-BENZ C350 2007 W203 Owner's Manual

360 Practical hints
Where will I find ...?
Storing the Minispare wheel
Place Minispare wheel3 in wheel
well.
Place vehicle tool kit storage well
casing4 over the Minispare wheel.
Make sure arrow2 on vehicle tool kit
storage well casing4 points in the
direction of travel.
Place storage well casing (page 356)
over vehicle tool kit storage well
casing4 and turn the retaining screw
(
page 356) clockwise as far it will go
to secure the Minispare wheel.In case of a flat tire, you may temporarily
use the Minispare wheel when observing
the following restrictions:

Do not exceed a vehicle speed of
50 mph (80 km/h).

Drive to the nearest tire repair facility
to have the flat tire repaired or
replaced as appropriate.

Do not operate vehicle with more than
one Minispare wheel mounted.
For more information, see “Rims and Tires”
(
page 403).
Spare wheel bolts
1Wheel bolt for light alloy rims
2Wheel bolt for Minispare wheel (locat-
ed in trunk with spare wheel)
iArrow2 on vehicle tool kit storage well
casing4 must point in the direction of travel.
Otherwise you cannot place the storage well cas-
ing (
page 356) on top and secure the Minis-
pare wheel with the retaining screw
(
page 356).
!To prevent damage, always disengage trunk
floor handle from upper edge of trunk and lower
trunk floor before closing the trunk lid.
Warning!G
The dimensions of the Minispare wheel are
different from those of the road wheels. As
a result, the vehicle handling characteristics
change when driving with a Minispare wheel
mounted.
The Minispare wheel should only be used
temporarily, and should be replaced with a
regular road wheel as quickly as possible.
!Wheel bolts2 must be used when mount-
ing the Minispare wheel. The use of any wheel
bolts other than wheel bolts2 for the Minispare
wheel will physically damage the vehicle’s
brakes.
Warning!G
Make sure to use the original length wheel
bolts when remounting the original wheel
after it has been repaired.

361 Practical hints
Unlocking/locking in an emergency
Unlocking/locking in an emergency
Unlocking the vehicle
If you are unable to unlock the vehicle with
the SmartKey, open the driver’s door and
the trunk using the mechanical key. Removing the mechanical key
1Mechanical key locking tab
2Mechanical key
Move locking tab1 in direction of
arrow.
Slide mechanical key2 out of the
housing.Unlocking the driver’s door
1Unlocking
Insert the mechanical key into the
driver’s door lock until it stops.
Turn the mechanical key counterclock-
wise to position1 until the locking
knob moves up.
The driver’s door is unlocked.
Pull the door handle to open the
driver’s door.
iUnlocking and opening the driver’s door
and/or the trunk with the mechanical key will
trigger the anti-theft alarm system*.
To cancel the alarm, do one of the following:

Press buttonŒ or‹ on the
SmartKey.

Insert the SmartKey in the starter switch.

362 Practical hints
Unlocking/locking in an emergency
Unlocking and opening the trunk
A minimum height clearance of 5.71 ft
(1.74 m) is required to open the trunk lid.
The trunk lid lock is located next to the
handle above the rear license plate recess.
1Unlocking in an emergency
2HandleInsert the mechanical key into the
trunk lid lock until it stops.
Turn the mechanical key
counterclockwise to position1.
The trunk lid unlocks.
Pull on handle2.
The trunk opens.
Turn the mechanical key back and
remove it from the trunk lid lock.
Locking the vehicle
If you can not lock the vehicle with the
SmartKey, do the following:
Close the passenger door, the rear
doors and the trunk.
Press the central locking switch in the
center console (
page 100).
Check to see whether the locking
knobs on the doors have moved down.
If necessary push them down manually.
Remove the mechanical key out of the
SmartKey (
page 361).
Check whether the trunk is locked.
If necessary, lock the trunk with the
mechanical key (
page 99).
Close the driver’s door.
Except for the driver’s door, the vehicle
should now be locked.
!The trunk lid swings open upwards
automatically. Always make sure there is suffi-
cient overhead clearance.

363 Practical hints
Unlocking/locking in an emergency
1Locking
Insert the mechanical key into the
driver’s door lock until it stops.
Turn the mechanical key clockwise to
position1.
The driver’s door is locked.Manually unlocking the transmission
gear selector lever
In case of power failure, the transmission
gear selector lever can be manually un-
locked, e.g. to tow the vehicle.
Slide out the swiveling cup holder
(
page 240).
1Tool
Insert a tool1 (e.g. flat blade screw
driver) into the opening.
Perform the following two steps
simultaneously:
Press tool1 forward in direction
of the arrow.
Move gear selector lever from
positionP.
Remove tool1 from the opening.
iThis procedure does not arm the anti-theft
alarm system, nor does it lock the fuel filler flap.
iThe gear selector lever is locked again when
moving it to positionP.

364 Practical hints
Opening/closing in an emergency
Power tilt/sliding sunroof*
You can open or close the tilt/sliding
sunroof manually should an electrical
malfunction occur.
The tilt/sliding sunroof drive is located
behind the lens1 of the interior overhead
light.
1Lens
Remove SmartKey from the starter
switch.
Pry off lens1 using a flat blade
screwdriver.2Locking tabs
Slide both locking tabs2 in direction
of the arrows.
Lower the rear of the cover.
Remove the cover.
Take the crank3 out of the Mer-
cedes-Benz vehicle literature pouch.3Crank
Insert crank3 through hole on the left
side.
Turn crank3 clockwise to:

slide sunroof closed

raise sunroof at the rear
Turn crank3 counterclockwise to:

slide sunroof open

lower sunroof at the rear
iDo not disconnect electrical connectors.
iTurn crank3 slowly and smoothly.
The tilt/sliding sunroof must be synchronized af-
ter being operated manually (
page 226).

365 Practical hints
Resetting activated head restraints
Resetting activated head restraints
Resetting activated head restraints
If the active head restraints have been trig-
gered in a rear-end collision, the active
head restraints must be reset. Otherwise,
the active head restraint cannot offer any
additional protection in the event of anoth-
er rear-end collision.
You can tell that the head restraints have
been triggered when they have been
moved forward and cannot be adjusted.
1Head restraint cushion
2Head restraint cover
3Reset tool
4Hole
Take the reset tool3 out of the
Mercedes-Benz vehicle literature
pouch.
Guide reset tool3 into the hole4 be-
tween the rear head restraint cover2
and the head restraint cushion1.
Press the reset tool3 forward in di-
rection of the arrow.
Press the reset tool3 downward until
you hear the head restraint release
mechanism audibly engage.
Pull out reset tool 3.
Firmly press the head restraint
cushion1 back toward the rear head
restraint cover2 until it engages.
Repeat this procedure on the active
head restraint for the second front
seat.
For information on active head restraints,
see “Active head restraint” (
page 73).
For information on head restraint adjust-
ment, see “Seats” (
page 34).
iFor your convenience, we recommend that
you have this work carried out by an authorized
Mercedes-Benz Center.
You will find the reset tool for manually operating
the active head restraints in the Mercedes-Benz
vehicle literature pouch.
Warning!G
For safety reasons, have the active head re-
straints checked by an authorized
Mercedes-Benz Center after a rear-end
collision.
Warning!G
When pushing back the head restraint cush-
ion, take care that your fingers do not be-
come caught between the head restraint
cushion and the cover. Failing to do so may
lead to injury.!Be careful not to damage upholstery.

366 Practical hints
Replacing SmartKey batteries
If the batteries in the SmartKey are
discharged, the vehicle can no longer be
locked or unlocked. It is recommended to
have the batteries replaced at an
authorized Mercedes-Benz Center.
Batteries contain materials that can harm
the environment if disposed of improperly.
Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries
for recycling.SmartKey
Replacement batteries: Lithium, type
CR 2025 or equivalent.
Remove the mechanical key from the
SmartKey (
page 361).
1Mechanical key
2Battery compartment
Insert mechanical key1 into the
opening.
Press mechanical key1 in direction of
arrow.
The battery compartment2 is un-
latched.
Pull battery compartment2 out of the
housing.
3Batteries
4Contact spring
Remove the batteries3.
Using a lint-free cloth, insert new
batteries3 under the contact
springs4 with the positive terminal
(+) side facing up.
Return battery compartment2 into
housing until it locks into place.
Slide mechanical key 1 back into the
SmartKey.
Check the operation of the SmartKey.
Warning!G
Keep the batteries out of reach of children.
If a battery is swallowed, seek medical help
immediately.
iWhen inserting the batteries, make sure
they are clean and free of lint.
iWhen replacing batteries, always replace
both batteries of both SmartKeys.
The required replacement batteries are available
at any Mercedes-Benz Center.

367 Practical hints
Replacing bulbs
Replacing bulbs
Safe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp
assemblies are in good working order at all
times.Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See an authorized
Mercedes-Benz Center for headlamp
adjustment.iIf the headlamps or front fog lamps are
fogged up on the inside as a result of high
humidity, driving the vehicle a distance with the
lights on should clear up the fogging.
iSubstitute bulbs will be brought into use
when lamps malfunction. Read and observe the
messages in the multifunction display
(
page 349).

368 Practical hints
Replacing bulbs
Bulbs Front lamps
Rear lamps
LampType
1Additional turn signal
lampLED
2Halogen headlamp:
Turn signal lamp
Bi-Xenon* headlamp:
Turn signal lamp
1156 A
2357 A
3Halogen headlamp:
Low beam
Bi-Xenon* headlamp:
Low and high beam
1
1Vehicles with Bi-Xenon* headlamps: Low beam
and high beam use the same D2S-35W lamp. Do
not replace the Xenon bulbs yourself. Contact an
authorized Mercedes-Benz Center.
H7 (55 W)
D2S-35 W
4Halogen headlamp:
High beam/high beam
flasher
Bi-Xenon* headlamp:
High beam flasher
H7 (55 W)
H7 (55 W)
Parking and standing
lampW5W
LampType
5Front fog lampHB4 (51 W)
Corner-illuminating
front fog lamps*H7 (55 W)
6Side marker lampW5W
LampType
7High mounted brake
lampLED
8Brake lampP21W
9Turn signal lampPY 21 W
aParking and side
marker lampP 21/5 W
bBackup lampP21W
cLicense plate lampsC5W
dRear fog lamp
(driver’s side only), tail
and standing lampP 21/4 W

369 Practical hints
Replacing bulbs
Notes on bulb replacement

Only use 12 volt bulbs of the same type
and with the specified watt rating.

Switch lights off before changing a bulb
to prevent short circuits.

Always use a clean lint-free cloth when
handling bulbs.

Your hands should be dry and free of oil
and grease.

If the newly installed bulb does not
come on, visit an authorized
Mercedes-Benz Center.
Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Center:

Additional turn signals in the exterior
rear view mirrors

High mounted brake lamp

Xenon* lamps

Front fog lamps

Front side marker lamps
Warning!G
Bulbs and bulb sockets can be very hot.
Allow the lamp to cool down before
changing a bulb.
Keep bulbs out of reach of children.
Halogen lamps contain pressurized gas.
A bulb can explode if you

touch or move it when hot

drop the bulb

scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
!Do not replace the LEDs yourself. You could
otherwise damage the LEDs or parts of the
vehicle. Only have the LEDs replaced by an
authorized Mercedes-Benz Center.