tow MERCEDES-BENZ C350 4MATIC 2007 W203 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: C350 4MATIC, Model: MERCEDES-BENZ C350 4MATIC 2007 W203Pages: 441
Page 8 of 441
Contents
Maximum tire inflation pressure .. 301
Uniform Tire Quality Grading
Standards (U.S. vehicles) ............. 302
Tire ply material ........................... 304
Tire and loading terminology ........ 304
Rotating tires ............................... 307
Winter driving .................................... 308
Winter tires .................................. 308
Block heater (Canada only) .......... 309
Snow chains................................. 309
Maintenance ...................................... 310
Maintenance service indicator
message....................................... 310
Calling up the maintenance
service indicator display............... 312
Resetting the
maintenance service indicator ..... 312
Vehicle care ....................................... 313
Cleaning and care of the vehicle .. 313
Practical hints.................................. 321
What to do if … ................................... 322
Lamps in instrument cluster ......... 322
Lamp in center console................. 331
Vehicle status messages
in the multifunction display........... 333
Where will I find ...? ............................ 356
First aid kit .................................... 356
Vehicle tool kit .............................. 356
Minispare wheel............................ 359
Spare wheel bolts ......................... 360
Unlocking/locking in an emergency... 361
Unlocking the vehicle.................... 361
Locking the vehicle ....................... 362
Manually unlocking the
transmission gear selector lever ... 363
Opening/closing in an emergency ..... 364
Power tilt/sliding sunroof* ........... 364
Resetting activated head restraints .... 365
Resetting
activated head restraints .............. 365
Replacing SmartKey batteries ............ 366
SmartKey ...................................... 366Replacing bulbs .................................. 367
Bulbs............................................. 368
Replacing bulbs for front lamps .... 370
Replacing bulbs for rear lamps ..... 373
Replacing wiper blades ...................... 375
Removing and installing
wiper blades ................................. 375
Flat tire............................................... 377
Preparing the vehicle .................... 377
Mounting the Minispare wheel...... 377
MOExtended system* ................... 382
Battery ............................................... 383
Disconnecting the battery ............ 384
Removing the battery ................... 384
Charging and
reinstalling the battery.................. 385
Reconnecting the battery ............. 385
Jump starting...................................... 386
Towing the vehicle.............................. 388
Installing towing eye bolt .............. 390
Fuses.................................................. 391
Main fuse box
in passenger compartment ........... 392
Fuse box
in engine compartment................. 392
Fuse box in trunk .......................... 394
Page 17 of 441
16 Introduction
Operating safety
Proper use of the vehicle
Proper use of the vehicle requires that you
are familiar with the following information
and rules:
the safety precautions in this manual
the “Technical data” section in this
manual
traffic rules and regulations
motor vehicle laws and safety
standards
Warning!G
Work improperly carried out on electronic
components and associated software could
cause them to cease functioning. Because
the vehicle’s electronic components are
interconnected, any modifications made
may produce an undesired effect on other
systems. Electronic malfunctions could
seriously impair the operating safety of your
vehicle.
See an authorized Mercedes-Benz Center
for repairs or modifications to electronic
components.
Other improper work or modifications on the
vehicle could also have a negative impact on
the operating safety of the vehicle.
Some safety systems only function while the
engine is running. You should therefore
never turn off the engine while driving.
Warning!G
Heavy blows against the vehicle underbody
or tires/wheels, for example when running
over an obstacle, road debris or a pothole,
may cause serious damage and impair the
operating safety of your vehicle. If you feel a
sudden significant vibration or ride distur-
bance, or you suspect that damage to your
vehicle has occurred, you should turn on
your hazard warning flashers, carefully slow
down, and drive with caution to an area
which is a safe distance from the road.
Inspect the vehicle underbody and
tires/wheels for possible damage. If the
vehicle appears unsafe, have it towed to the
nearest authorized Mercedes-Benz Center
or other qualified maintenance or repair
facility for further inspection or repairs.
Warning!G
Various warning labels are attached to your
vehicle. These warning labels are intended
to make you and others aware of various
risks. You should not remove any of these
warning labels unless explicitly instructed to
do so by information on the label itself.
Removal of any of these labels may cause
you and others to be unaware of certain
risks which may result in an accident and/or
personal injury.
Page 55 of 441
54 Getting started
Parking and locking
You have now completed your first drive.
You have properly stopped and parked
your vehicle. End your drive as follows.
Parking brake
Warning!G
Vehicles with manual transmission:
Wait until the vehicle is stationary before
removing the SmartKey from the starter
switch. The vehicle cannot be steered when
the SmartKey is removed.
Warning!G
With the engine not running, there is no
power assistance for the brake and steering
system. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the
vehicle.
Warning!G
Do not park this vehicle in areas where
combustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
To reduce the risk of personal injury, or
damage to the vehicle or the vehicle
drivetrain, as a result of vehicle movement,
always do the following before turning off
the engine and leaving the vehicle:
Keep right foot on brake pedal.
Manual transmission: Move the gear-
shift lever into neutral position (no gear
is selected).
Firmly depress parking brake pedal.
Manual transmission: Move the gear-
shift lever into first or reverse gear.
Automatic transmission*: Move the
gear selector lever to positionP.
Slowly release brake pedal.
When parked on an incline, always turn
the front wheels towards the road curb.
Turn the SmartKey in the starter switch
to position0 and remove.
Take the SmartKey with you and lock
the vehicle when leaving, which could
endanger other road users when you en-
gage the parking brake.
Warning!G
Do not engage the parking brake while the
vehicle is in motion. Doing so can cause the
rear wheels to lock up. You could lose con-
trol of the vehicle and cause an accident. In
addition, the vehicle’s brake lights do not
light up when the parking brake is engaged,
which could endanger other road users.
Page 56 of 441
55 Getting started
Parking and locking
1Release handle
2Parking brake pedal
Step firmly on parking brake pedal2.
When the engine is running, the brake
warning lamp; (USA only)
or3(Canada only) in the
instrument cluster comes on.
Switching off headlamps
Turn the exterior lamp switch toM
(
page 50).
For more information, see “Lighting”
(
page 109).
Turning off engine
Manual transmission: Move the gear-
shift lever into first or reverse gear.
Automatic transmission*: Place the
gear selector lever in positionP.
Apply the parking brake (page 54).
Turn the SmartKey in the starter switch
to position0 (
page 32).
Remove the SmartKey from the starter
switch.
The immobilizer is activated.
Warning!G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Children
could release the parking brake and/or
move the gear selector lever* from
positionP, either of which could result in an
accident and/or serious personal injury.
PositionP alone may not prevent your vehi-
cle from moving, possibly hitting people or
objects. Always set the parking brake in ad-
dition to shifting to positionP (
page 153)
(manual transmission: first or reverse gear
(
page 149)).
When parked on an incline, turn front wheel
towards the road curb.
Getting out of your vehicle without taking
the above measurements to secure it is
dangerous.
iAlways set the parking brake in addition to
shifting to positionP (manual transmission: first
or reverse gear).
On slopes, turn the front wheels towards the
road curb.
iVehicles with automatic transmission: The
SmartKey can only be removed from the starter
switch with the gear selector lever in positionP.
Page 87 of 441
86 Safety and Security
Driving safety systems
For more information, see the “Practical
hints” section (
page 327) and
(
page 335).Electronic traction system
The electronic traction system is a
component of ESP
®.
The electronic traction system improves
the vehicle’s ability to utilize available
traction, especially under slippery road
conditions by applying the brakes to a
spinning wheel.
When you switch off the ESP
®, the
electronic traction system is still enabled.Switching off the ESP
®
To improve the vehicle’s traction, turn off
the ESP® in driving situations where it
would be advantageous to have the drive
wheels spin and thus cut into surfaces for
better grip such as:
when driving with snow chains
in deep snow
in sand or gravel
!Vehicles without 4MATIC:
Because the ESP® operates automatically, the
engine must be turned off (SmartKey in starter
switch position0 or1) when
the parking brake is being tested on a brake
test dynamometer
the vehicle is being towed with the front axle
raised
Active braking action through the ESP
® may
otherwise seriously damage the brake system.
For information on vehicles with 4MATIC, see
“Four wheel electronic traction system (4MATIC)
with the ESP
® ” (page 88).
iThe ESP® will only function properly if you
use wheels of the recommended tire size
(
page 403).
Warning!G
If you are driving too fast, the electronic
traction system cannot reduce the risk of an
accident.
The electronic traction system cannot pre-
vent the natural laws of physics from acting
on the vehicle.
Warning!G
The ESP® should not be switched off during
normal driving other than in the circum-
stances described below. Disabling of the
system will reduce vehicle stability in stan-
dard driving maneuvers.
Do not switch off the ESP
® when a
Minispare wheel is mounted.
!Switch on the ESP® immediately if the
aforementioned circumstances do not apply
anymore.
Page 89 of 441
88 Safety and Security
Driving safety systems
Four wheel electronic traction system
(4MATIC) with the ESP®
Models with all-wheel-drive only.
The 4MATIC improves vehicle’s ability to
use available traction, e.g. during winter
operation in mountains under snowy
conditions, by applying power to all four
wheels.
Warning!G
If you see the ESP® warning lampv
flashing in the instrument cluster, proceed
as follows:
While driving off, apply as little throttle
as possible
While driving, ease up on the accelera-
tor
Adapt your speed and driving style to
the prevailing road conditions
Failure to observe these guidelines could
cause the vehicle to skid.
The ESP
® cannot prevent accidents result-
ing from excessive speed.
!Do not tow with one axle raised.
Otherwise the transfer case can be damaged,
which is not covered by the Mercedes-Benz
Limited Warranty.
!Performance testing must only be conduct-
ed on a two-axle dynamometer.
Otherwise the transfer case can be damaged,
which is not covered by the Mercedes-Benz
Limited Warranty.
!Because the ESP® operates automatically,
the engine must be shut off (SmartKey in starter
switch position0 or1) when the parking brake is
being tested on a brake test dynamometer.
Active braking action through the ESP
® may
otherwise seriously damage the front or rear axle
brake system.
Operational tests with the engine running can
only be conducted on a two-axle dynamometer.
iAt highly demanding operating conditions,
the electronic traction system may temporarily
switch off to prevent overheating of the drive
wheel brakes. The message
unavailable
See Operator’s Manual
will then appear in
the multifunction display while the ESP® warning
lampv is flashing. The ESP® is still function-
ing normally.
Page 100 of 441
99 Controls in detail
Locking and unlocking
Valet locking
The lock is located next to the handle
above the rear license plate recess.
1Neutral position
2Locked
Close the trunk (page 97).
Pull the mechanical key out of the
SmartKey (
page 361).
Insert the mechanical key in the trunk
lid lock.
Turn the mechanical key clockwise to
position2 and remove the mechani-
cal key in that position to lock the
trunk.
The trunk remains locked even when the
vehicle is centrally unlocked.
Insert the mechanical key in the trunk
lid lock.
Turn the mechanical key counterclock-
wise to neutral position1 and remove
the mechanical key in that position to
unlock the trunk.
You can now open the trunk
(
page 96).
Automatic central locking
The doors and the trunk automatically lock
when the ignition is switched on and the
wheels are turning at vehicle speeds of
approximately 9 mph (15 km/h) or more.
You can open a locked door from the
inside. Open door only when conditions
are safe to do so.
You can deactivate the automatic locking
mode using the control system, see “Set-
ting automatic locking” (
page 143).
iTo deny any unauthorized person access to
the trunk, lock it separately with the mechanical
key. Leave only the SmartKey less its mechani-
cal key with the vehicle.
iYou can only cancel the separate trunk lock-
ing mode by means of the mechanical key.
iThe doors unlock automatically after an ac-
cident if the force of the impact exceeds a preset
threshold.
To prevent the vehicle door locks from locking,
deactivate the automatic central locking when
the vehicle
is pushed or towed
is on a test stand
Page 150 of 441
149 Controls in detail
Manual transmission
Manual transmission
Manual transmission is standard
equipment on select models and not
available on all models.
For information on driving with a manual
transmission, see “Manual transmission”
(
page 46).
Warning!G
For vehicles equipped with a manual trans-
mission, getting out of your vehicle with the
gearshift lever not engaged in first or
reverse gear and parking brake engaged is
dangerous.
Also, when parked on an incline, an engaged
first or reverse gear alone may not prevent
your vehicle from moving, possibly hitting
people or objects.
Always set the parking brake in addition to
engaging first or reverse gear (
page 54).
When parked on an incline, turn front wheels
towards the road curb.
Do not park this vehicle in areas where
combustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
Warning!G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Children
could move the gearshift lever, which could
result in an accident and/or serious person-
al injury.
Warning!G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced
vehicle control. Your vehicle’s ABS will not
prevent this type of loss of control.
Warning!G
Make sure that absolutely no objects are ob-
structing the pedals’ range of movement.
Keep the driver’s footwell clear of all obsta-
cles. If there are any floormats or carpets in
the footwell, make sure that the pedals still
have sufficient clearance.
During sudden driving or braking maneuvers
the objects could get caught between or be-
neath the pedals. You could then no longer
brake or accelerate. This could lead to acci-
dents and injury.
Page 154 of 441
153 Controls in detail
Automatic transmission*
Gear selector lever positions
The current gear selector lever position
appears in the multifunction display.
1Current gear selector lever position
Effect
ìPark position
Gear selector lever position
when the vehicle is parked. Place
gear selector lever in park
positionP only when vehicle is
stopped. The park position is not
intended to serve as a brake
when the vehicle is parked.
Effect
Rather, the driver should always
set the parking brake in addition
to placing the gear selector lever
in park positionP to secure the
vehicle.
The SmartKey can only be
removed from the starter switch
with the gear selector lever in
park positionP. With the
SmartKey removed, the gear
selector lever is locked in park
positionP.
If the vehicle’s electrical system
is malfunctioning, the gear
selector lever could remain
locked in park positionP
(
page 363).
íReverse gear
Place gear selector lever in
positionR only when vehicle is
stopped.
Effect
ëNeutral
No power is transmitted from the
engine to the drive axle. When
the brakes are released, the
vehicle can be moved freely
(pushed or towed).
To avoid damage to the trans-
mission, never engage neutral
positionN while driving.
If the ESP
® is deactivated or
malfunctioning:
Move gear selector lever to neu-
tral positionN only if the vehicle
is in danger of skidding, e.g. on
icy roads.
êDrive
The transmission shifts
automatically. All forward gears
are available.
Page 155 of 441
154 Controls in detail
Automatic transmission*
!Coasting the vehicle, or driving for any other
reason with gear selector lever in neutral
positionN can result in transmission damage
that is not covered by the Mercedes-Benz
Limited Warranty.Warning!G
PositionP alone is not intended to or capa-
ble of preventing your vehicle from moving,
possibly hitting people or objects. Always
set the parking brake in addition to shifting
to park positionP (
page 54).
When parked on an incline, turn the front
wheels towards the road curb.
Do not park this vehicle in areas where com-
bustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
Warning!G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Children
could move the gear selector lever from
park positionP, which could result in an
accident and/or serious personal injury.
Getting out of your vehicle without taking
the above measurements to secure it is
dangerous.