lock MERCEDES-BENZ CL-Class 2003 C215 Comand Manual

107 Telephone
Emergency call
If there is an active Tele Aid call, the tele-
phone main menu will disappear and you
will see the message “Phone off”.
After the Tele Aid call is ended the telepho-
ne main menu will reappear.
See your vehicle’s operator’s manual.Initiating an emergency call
If the telephone main menu or a memory
menu is displayed

Press number key 1 longer than 2 se-
conds (quick-dialing).
The telephone begins dialing, the Ö
button is highlighted.
When the call is initiated, the call time
will appear.
Do not place the emergency call

Turn the right-hand rotary/push-button
v to highlight the Ö button and
press to confirm or press *.
Ending the call, use one of the three ways:

Press the right-hand rotary/push-
button v to confirm the Ö button.
or

Press a.
or

Press *.
P82.85-9418-31US
TEL
Phone off.
Telephone is ready for operationiPlease ensure that the number stored in
the memory location is the number you
want to dial in case of an emergency
(default is 9-1-1).
The function will also be performed if
the telephone is locked.ABC/123
Last CallsPhone Book
CallsTELABCDEFGHIJKLMNO
PQRSTUVWXYZDialing: 911
P82.85-9419-31US SENDENDMUTE

130 NavigationDestination input
Turn the right-hand rotary/push-button
v to highlight the desired block and
press to confirm.
The selection menu “Destination Entry”
will appear.

Press the right-hand rotary/push-
button v longer than 2 seconds to cal-
culate the route (
page 141).Selecting a city center
You can activate the list “Center Entry” in
the main address menu (
page 123) or af-
ter selecting a city (
page 126).

Turn the right-hand rotary/push-button
v to highlight “Center” and press to
confirm.
The list “Center Entry” will appear.

Turn the right-hand rotary/push-button
v to highlight the desired entry and
press to confirm.
The selection menu “Destination Entry”
will appear.

Press the right-hand rotary/push-
button v longer than 2 seconds to cal-
culate the route (
page 141).
iThe house numbers usually appear on
the list in blocks, e.g.
1-5 odd numbers
42-50 even numbers
1-50 mixed numbers
P82.85-9439-31US
NAVI Center EntryISLAND, STATEN
STATEN, ISLAND

134 NavigationDestination input
Press the right-hand rotary/push-but-
ton v or wait 6 seconds to calculate
the map with the new scale.
A clock symbol will appear on the top
right of the display, the square will be
masked.Zooming out for less detailed map

Press /.
The scale selector will appear and
show the current _ and the next smal-
ler scale ?.

Press the right-hand rotary/push-but-
ton v or wait 6 seconds to calculate
the map with the new scale.
A clock symbol will appear on the top
right of the display.Confirming destination and calculating
route
The crosshairs highlight the desired desti-
nation

Press the right-hand rotary/push-
button v longer than 2 seconds.

Then calculate the route (
page 141).
iYou can continue to decrease the scale
within 5 seconds
Press /.

Turn the right-hand rotary/push-
button v to the right.

149 Navigation
Route guidance
Requesting route mode
Turn the right-hand rotary/push-button
v in the selection menu “Destination
Info” to highlight “Options” and press
to confirm.
The settings for the current route are
displayed. Switching back to the symbol or map dis-
play

Press * or wait approximately 15
seconds. Activating the location map
If route guidance is active

Turn the right-hand rotary/push-button
v in the selection menu “Destination
Info” to highlight “Location Map” and
press to confirm.
The location map faces north (North-
up).
P82.85-9458-31US
NAVI Route Mode
Short Route

No Freeway, with Toll,
with Ferry

No Blocking

iSelecting calculation mode
(page 141)
Selecting a detour during destination
guidance (
page 162)
Marking a way point (
page 160)

162 NavigationRoute guidanceMain detour menu
1It is possible to block route sections
ahead
2Ends the detour function, the previous
route is calculated

Traffic Jam Ahead/Detour in Route
List not activated:
“Cancel” cannot be selected

Traffic Jam Ahead/Detour in Route
List activated:
“Cancel” is highlighted
3It is possible to block route sections in
the route list (
page 164)

Press ) at any time.
The main detour menu will appear.

Turn the right-hand rotary/push-button
v to highlight the desired menu field
and press to confirm.
^
Selecting a detour
P82.85-9479-31US
NAVI Traffic Jam
Traffic Jam Ahead...
Cancel Traffic Jam...
Cancel Detour... Detour in Route List...
12
32
iTraffic jams are identified by the driver,
not by the COMAND.
I f y o u s w i t c h o f f C O M A N D f o r m o r e t h a n
30 minutes during active route
guidance, all manually entered traffic
jams are deleted.

163 Navigation
Route guidance
Traffic jam ahead
If a traffic jam lies ahead, you can block the
route sections following the next intersec-
tion/the next turn-off.Traffic jam menu1Length of the blocked route section in
miles

Turn the right-hand rotary/push-button
v to highlight “Traffic Jam Ahead...” in
the main detour menu and press to
confirm.
The traffic jam menu will appear.Entering the length of the blocked route
section
Increasing the blocked section

Turn the right-hand rotary/push-button
v to the right.
Decreasing the blocked section

Turn the right-hand rotary/push-button
v to the left.
Calculating detour

Press the right-hand rotary/push-
button v.
The route will be re-calculated. An in-
formation menu will appear.
Then COMAND continues route
guidance.
P82.85-9480-31US
NAVI Traffic JamRoute section to detour:0.3 mi
1
iCOMAND suggests reasonable route
sections.
Minimum/maximum length of detour is
governed by the logical grouping of rou-
te sections. If additional detour seg-
ments are required after the original
detour, they must be requested indivi-
dually.
iYou can also select “Traffic Jam Ahead”
during the course of a detour. The cur-
rent detour will then be cancelled.

164 NavigationRoute guidance
Detour in route list
Turn the right-hand rotary/push-button
v to highlight “Detour in Route List” in
the main detour menu and press to
confirm.
The message “The route list is being
calculated” will appear.
Then the route list will appear.
Route list1Street cannot be blocked off
2Symbol “+”: street contains several
sections which can be blocked off
Displaying an entry in full in a window
Press u.

Press u again to remove the window.
iCOMAND will delete an existing detour
if you
enter a new detour

switch off the system for more than
30 minutes while a detour is activa-
ted
After you have switched the COMAND
on again you will see the message “Ma-
nual route exclusions being reset”.
P82.85-9481-31US
NAVI Traffic Jam
4081 E OLYMPIC B
399 S HILL
250 S GRAND AVE
630 W 5TH
3589 S FIGUEROA 200 N STATE
12
1.0 MI
2.4 MI
1.8 MI
0.5 MI
1.6 MI 1.2 MI

165 Navigation
Route guidance
Calling detailed route list Detailed route list3Blocked route section R
4Symbol “-” - sections of a road are dis-
played
Press %.
The detailed route list will appear.Blocking off several streets/street sec-
tions

Press the right-hand rotary/push-but-
ton v.
The block function is active, the
symbolR will appear in front of the
entry.

Turn the right-hand rotary/push-button
v to the right.
With each turn, you will block another
section.
Undoing street block

Turn the right-hand rotary/push-button
v to the left.
The symbolR will disappear.
Switching back to the route list

Press /.
The symbol “+” appears in front of the
street section.
The blocking function is still active.Canceling blocking function, do not recal-
culate the route

Press *.
The traffic jam menu will appear.
Ending the blocking function, re-calcula-
ting the route with the blocks selected

Press the right-hand rotary/push-
button v.
COMAND re-calculates the route in the
previously selected calculation mode.
A corresponding message will appear.
Then the symbol display will appear
again and COMAND will continue route
guidance.
P82.85-9482-31US
NAVI Traffic Jam
4081 E OLYMPIC B
399 S HILL
399 S HILL
399 S HILL 200 N STATE
250 S GRAND AVE
1.0 MI
0.8 MI
1.2 MI
0.4 MI1.2 MI
1.8 MI4
3

187 Info Services/System settings
System settings

System settings
6Displays the new message
7Switches back to the main menu
There is more than one message
Press the right-hand rotary/push-
button v to move to the next page.
Activating the main service menu

Press *.
Switching back to e.g. radio main menu

Turn the right-hand rotary/push-button
v to highlight “No” and press to con-
firm.
Main system settings menu1Date and time
You can select the time format
(
page 196)
2Adjusts the brightness
3Activates “Settings” menu
4Switching an auxiliary audio source on
(page 200)
5Country setting, with a time zone
(page 192)

Press (.
The main service menu will appear.

Turn the right-hand rotary/push-button
v to highlight “System Settings” and
press to confirm.
The main system settings menu will ap-
pear.
P82.85-9515-31US
SVC
Ye s
No
6
7
New Info Received.
Read later when stopped ?
Activating the main settings menu
P82.85-9518-31US
SVC Sys Settings
01.01.2002
Brightness
AuxSettings
10:23 AM
1
2
4
3
Country: USA
Timezone:Eastern
5
iYou will see information 5 if the clock
has been set to GPS reception and if a
country, e.g. USA and a time zone was
selected.

190 Info Services/System settingsSystem settingsYou can select the following languages
“Adopt from Instrument Cluster”
COMAND will use the same language
as is set in instrument cluster

“Deutsch”

“English” (metric)
Distance measured in km,
speed in km/h

“English” (imperial)
Distance measured in yards and miles,
speed in miles per hour (mph)

“Español”

“Français”

“Italiano”

“Nederlands”COMAND is equipped with an integrated
clock, which it shows in the main system
settings menu.
Automatically
COMAND automatically sets date and time
if the GPS time is received.
However, you can make the following ad-
justments:
Set the time in increments of 30 minu-
tes (
page 191)

Set the time by selecting a country and
the time zone (
page 192)Manually
You must always set the clock manually
(
page 195), if

COMAND does not receive a GPS time

the clock has been disconnected from
the vehicle battery

the dates of the change between sum-
mer and winter time are not available
Setting date and timeiThe clock displays e.g. the estimated
time of arrival at the destination during
route guidance.