wheel MERCEDES-BENZ CL-Class 2003 C215 Comand Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2003, Model line: CL-Class, Model: MERCEDES-BENZ CL-Class 2003 C215Pages: 225, PDF Size: 2.03 MB
Page 19 of 225
11 At a glance
Multifunction display
Multifunction display
The starter switch must be in position 1 or
2. Refer to vehicle operating instructions.
You can operate the following systems
with steering wheel buttons 4 and 5:
Radio
CD (CD changer and CD drive)
Auxiliary audio source, e.g. tape recor-
der (
page 200)
Telephone
For more detailed information, refer to
“Multifunction display” in the chapters dis-
cussing the radio, CD, telephone opera-
tion.
Function
1
Multifunction display in speedo-
meterOperating the control system
2
Adjusting the volume
I lowers the volume
J raises the volume
3
Making a call
K Accept incoming call or
starts dialing
L End a call or end Tele Aid
4
Switching between menu sys-
tems
E next system
H previous system
5
Moving within a menu system
F next display
G previous displayFunction
Page 22 of 225
14 At a glanceQuick reference COMANDAt the multifunction steering wheel
To raise the volume
Press J.
To lower the volume
Press I.
At the COMAND operating unit
Turn the turning wheel on the left-hand
rotary/push-button v during a voice
output.
For the audio sources
Radio
CD (CD drive and CD changer)
you can set the volume jointly.For the service sources
Voice output during route guidance
(navigation system)
and
Voice control system (refer to separate
operating instruction)
you can set the volume jointly.
For the service source
Telephone
you can alter the listening volume for the
telephone only.Switching on
Press c.
The radio is switched on. The station
last tuned to will begin to play.
Changing the radio band
Press c to switch between FM- and
AM-Band.
Adjusting the volume
Radio operation
P82.85-9304-31US
FM1FM Presets
Auto PresetsSound
WB Scan
97.1 FM
Page 38 of 225
30 AudioRadio operationYou can use the following functions:
Automatic seek tuning (
page 30)
Seek tuning at the multifunction stee-
ring wheel (
page 31)
Manual tuning (
page 31)
Station selection via number keypad
(presets) (
page 32)
Station selection via direct frequency
entry (
page 32)
Automatic station scan (
page 33)
Station selection from the preset menu
(page 38)Automatic seek tuning
Press g or h.FM- and AM-Bands, Weather Band WB
The radio will tune in to the next receivable
station (FM, AM) or channel (WB) with de-
scending/ascending frequency depending
on the direction of seek.
WB
Alternatively, you can select the channel
directly:
Press a number key 1 through 7.
Selecting a station
P82.85-9319-31US
88.1 FM
FM2
FM Presets
Auto Presets Scan
Sound
WB
Page 39 of 225
31 Audio
Radio operation
Seek tuning at the multifunction stee-
ring wheel
If the multifunctional display shows the
station frequency, then:
Press F or G to select a higher/
lower frequency preset.Manual tuning (FM, AM)
Press g or h longer than 2 se-
conds.
The menu fields will appear in dark grey
lettering.FM Band
The frequency displayed will change in in-
crements of 0.2 MHz.
AM Band
Tuning will take place in increments of
10 kHz.
iThe up/down arrows have different
functions depending on which mode the
seek function in the multifunction dis-
play is programmed to.
The two available options are Memory
Scan or Frequency Scan (Station
search). Refer to the vehicle operator’s
manual on how to program this option.
P82.85-9320-31US
AM Presets
Auto Presets Scan
1080 AM
Sound
WB AM1
iActivating the AM Band (
page 29).
Page 48 of 225
40 AudioRadio operation
Press # at the COMAND control
unit to switch on COMAND.
Press c at the COMAND control
unit to switch to radio operation.
Press E or H repeatedly on the
multifunction steering wheel until you
see the set-up for the current
station on the display.1Frequency band and the memory pre-
set, if applicable
2“SP” - memory, appears if “Memory” in-
stead of “Frequency” has been selec-
ted in the “Vehicle” submenu
3Frequency of the station selected
Repeatedly press F or G on the
multifunction steering wheel until the
desired station frequency appears.
The type of search depends on the set-
up for station selection in the “Vehicle”
submenu
“Memory” (SP) - the next saved sta-
tion is selected
“Frequency” - the next available
station is selected
Refer to “Control system” in chapter
“Controls in detail” in your vehicle's
operating instructions for further infor-
mation.
Press E or H at the multifunc-
tion steering wheel to display the next
or previous system.
Multifunction display
P82.85-9532-31US
97.1 FM
FM1
3
SP
2
1
Page 77 of 225
69 Telephone
Important notes
Close the windows and reduce all out-
side noise as much as possible when
you use hands-free operation.
A brief disconnection from the cellular
network is not a malfunction, as this
can occur when the network switches
areas. The phone will automatically try
to sign on to a network again.
If the message “Locked. Please enter
code” appears, enter the unlock code
to enable all telephone functions
(page 78).
If a menu other than the telephone
menu is displayed on the COMAND
screen, the display will change if an
outgoing call is sent out via the multi-
function steering wheel.In the following situations, it is not possible
or not yet possible to use the telephone:
The telephone is already unlocked but
is not or not yet registered in the net-
work.
The message “No Service” appears.
The telephone will try to register into
an existing network. If the network is
available, the telephone will be ready
for use.
The above message also appears
if the network is no longer available
due to weak signals
if you try to make a call (message
appears for 8 seconds)
The message “Telephone is being acti-
vated. Please wait.” appears.
COMAND prepares the telephone for
use. Select other system functions, e.g.
radio, by pressing the corresponding
button or wait until the telephone is ac-
tive.
One of the two messages “No telepho-
ne” or “Telephone not plugged in” ap-
pears.
Please connect the telephone.
The message “Telephone defective”
appears.
Please contact an authorized
Mercedes-Benz Center.
Page 87 of 225
79 Telephone
Telephone operation
If the phone memory has been downloa-
ded to COMAND, the menu fields “Phone
Book”, “Last Calls” and “Calls” will be avai-
lable.
If the memory was not downloaded, the
menu fields will be dimmed out.
Outgoing calls (
page 82).
Use one of these ways
When the telephone is connected to
the coiled cord, press a on the
COMAND control unit.
or
When the telephone is in portable mo-
de, press # on the phone.Accepting the call at the multifunction
steering wheel
1
CALLThe system detects an incoming call,
the phone ringsAccepting a call
Press K.
Audio source is automatically muted.
Ending a call
Press L.
The main telephone display appears.
Switching telephone operation off
Incoming call
P82.85-9547-31US
CALL
TEL
1
iYou can also accept a call, if another
display, e.g. navigation, is shown on the
multifunction display.iCommunication between the multifunti-
on display and the COMAND screen:
If different systems appear, the changes
made to COMAND will have no effect on
the driver information display.
Press the COMAND key a to
switch to the telephone functions.
Page 88 of 225
80 TelephoneTelephone operationAccepting a call using COMAND
1“Call”
The system detects an incoming call,
the phone rings.
Press the right-hand rotary/push-
button v to confirm the Ä button.
The display will change to the
call menu. An active audio source will
be muted.
Call menu2“00:01:21 h”
The call time appears
3Name or phone numberSwitching the microphone for the
hands-free telephone off
Turn the right-hand rotary/push-button
v to highlight the Ü button and
press to confirm.
Press the right-hand rotary/push-
button v again to cancel muting.
Setting the volume for hands-free opera-
tion
Raising the volume
Turn the turning wheel on the left-hand
rotary/push-button v to the right.
Lowering the volume
Turn the turning wheel on the left-hand
rotary/push-button v to the left.
ABC/123
Last CallsPhone Book
CallsTEL
1
ABCDEFGHIJKLMNO
PQRSTUVWXYZCall
P82.85-9378-31US SENDENDMUTE
iNo telephone menu is shown on the
screen
first press a
then you can accept or refuse the
call.ABC/123
Last CallsPhone Book
CallsTEL
3
0:01:27h
BRAEUER
2
P82.85-9379-31US SENDENDMUTE
Page 93 of 225
85 Telephone
Telephone operation
Dialing a number from the phone book
Dialing using the multifunction steering
wheel
In order to use this feature, the phone
book must have previously been downloa-
ded to the COMAND memory. This is per-
formed automatically each time the
portable phone is connected to the coiled
cord.
The telephone is ready for operation
(page 78).
Press E or H as often as neces-
sary until the telephone mode appears
in the multifunction display.
If ENTER CODE
appears, enter your unlock
code first (page 78).
The message NO ENTRY
appears when the
portable phone has been put into the crad-
le and no entries are stored in the phone
book.
Press F or G.
You are paging the phone book back-
wards or forwards in alphabetical or-
der. Name and memory location
appear.
or
Press F or G longer than 2 se-
conds.
You are scrolling through the phone
book very quickly.
The name that is selected appears in
the display.
P82.85-9546-31US
MERCEDES
TEL MO
iIf you do not wish to place a call, press
L. The process will be cancelled and
the message
READY
appears again.
Page 99 of 225
91 Telephone
Telephone operation
RedialDialing using the multifunction steering
wheel1The telephone is ready for operation.
2Number in the redial memory
3Number in the redial memory, dialing
has begun4Dialing is completed. Name or still the
dialed number (name has not been sa-
ved).5Memory location number, the last 10
dialed telephone numbers are stored
L01, number dialed last
L01 to L10, numbers dialed previously
6Call time
P82.85-9544-31US
READY
TEL
1
01305005
LO TEL
01111980
LO TEL
00:01:15
MERCEDES
LO TEL
6
23
4
5
K
K
L