lock MERCEDES-BENZ CL-CLASS 2007 Owners Manual

646 Practical hints
Replacing bulbs
IR emitter*
1Bulb holder
2Wire position
Turn bulb holder1 counterclockwise
until it disengages.
Take out bulb holder1.
Press both catches on left and right
sides of bulb holder1 and take bulb
out of holder.
Insert new bulb into holder until it en-
gages.
Insert bulb holder1 into guide in
headlamp. Wire2 must point down-
ward and to the right.
Turn bulb holder1 clockwise until it
engages and wire2 points downward
and to the left.
Additional turn signal lamp bulbs
The additional turn signal lamps in the ex-
terior rear view mirrors have LEDs.
If a malfunction occurs or LEDs fail to func-
tion, the entire turn signal unit must be re-
placed. Have the turn signal unit replaced
by an authorized Mercedes-Benz Center.
Front side marker lamp bulbs
Since replacing the side marker lamp bulbs
is a technically highly demanding process,
we recommend you have the side marker
lamp bulbs replaced by an authorized
Mercedes-Benz Center.Replacing bulbs for the rear lamps
Tail lamp unit
The tail lamp unit is equipped with HiP
bulbs and LED’s.
Warning!G
The bulbs in the tail lamp unit cannot be re-
placed individually. The tail lamp bulbs are
under pressure and could explode during an
attempt to replace them.
If the tail lamps (HiP bulbs and/or LED’S)
are malfunctioning, have them replaced at
an authorized Mercedes-Benz Center.
ProCarManuals.com

648 Practical hints
Replacing wiper blades
Vehicles with KEYLESS-GO*
Make sure the vehicle’s on-board elec-
tronics have status 1 (
page 337).
Turn combination switch to wiper
settingu (
page 372).
Press KEYLESS-GO start/stop button
repeatedly until windshield wipers
start.
Press KEYLESS-GO start/stop button
when the wiper arms are in a vertical
position.
Removing wiper blades
Fold the wiper arm forward until it
snaps into place.
Turn the wiper blade at a right angle to
wiper arm (arrow 1).
Slide the wiper blade sideways out of
the retainer in the direction of
arrow2.
Installing wiper blades
Slide the wiper blade onto wiper arm
until it locks in place.
Rotate the wiper blade into position
parallel to wiper arm.
Fold the wiper arm backward to rest on
the windshield. Make sure you hold
onto the wiper when folding the wiper
arm back.
!Do not pull on the wiper blade inserts. They
could tear.
!Make certain that the wiper blades are prop-
erly installed. Improperly installed wiper blades
may cause windshield damage.
ProCarManuals.com

650 Practical hints
Flat tire
Preparing the vehicle
Prepare the vehicle as described
(
page 649).
Take vehicle tool kit and vehicle jack
out of trunk (
page 632).
Take the Minispare wheel and wheel
bolts out of the trunk (
page 634).Lifting the vehicle
Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
or other sizeable objects.
One wheel chock is included with the
vehicle tool kit (
page 634).
When changing wheel on a level surface:
Place the wheel chock in front of and
another sizeable suitable object behind
the wheel that is diagonally opposite to
the wheel being changed.
Always try lifting the vehicle using the jack
on a level surface. However, should cir-
cumstances require you to do so on a hill,
place the wheel chock and another size-
able suitable object as follows:
Place the wheel chock and another
sizeable suitable object on the downhill
side blocking both wheels of the axle
not being worked on.
Warning!G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always en-
gage the electronic parking brake and block
wheels before raising vehicle with jack.
Do not disengage electronic parking brake
while the vehicle is raised. Be certain that
the jack is always vertical (plumb line) when
in use, especially on hills. Always try to use
the jack on level surface. Make sure the jack
arm is fully seated in the jack take-up brack-
et. Always lower the vehicle onto sufficient
capacity jackstands before working under
the vehicle.
ProCarManuals.com

654 Practical hints
Flat tire
Lowering the vehicle
Lower vehicle by turning crank coun-
terclockwise until vehicle is resting ful-
ly on its own weight.
Remove the jack.
1 - 5 Wheel bolts
Tighten the five wheel bolts evenly,
following the diagonal sequence
illustrated (1 to 5), until all bolts are
tight. Observe a tightening torque of
110 lb-ft (150 Nm).Before storing the jack, it should be fully
collapsed, with handle folded in (storage
position).Store the jack and the other vehicle
tools in the designated storage space
underneath the trunk floor
(
page 632).
Warning!G
Have the tightening torque checked after
changing a wheel. The wheels could come
loose if they are not tightened to a torque of
110 lb-ft (150 Nm).
iDo not activate the tire inflation pressure
monitor (
page 531) until a full size wheel/tire
with functioning sensor has been placed back
into service on the vehicle.
ProCarManuals.com

657 Practical hints
Batteries
Starter battery (example illustration from
CL 550)
1Negative terminal
2Positive terminal
Disconnecting starter battery
Secure vehicle in place with electronic
parking brake (
page 384).
Shift the automatic transmission toP
(
page 389).
Do not rub the battery with rags or cloths.
The battery could explode if touched due to
electrostatic charge or due to spark forma-
tion.
!Switch off the engine and switch off the ve-
hicle’s internal electrical functions (
page 658)
before you disconnect or remove the battery’s
terminal clamps. You could otherwise destroy
electronic assemblies such as the generator.
Have the battery checked regularly by an autho-
rized Mercedes-Benz Center. Refer to Mainte-
nance Booklet for maintenance intervals or
contact an authorized Mercedes-Benz Center for
further information.
!Do not connect any consumers directly to
the starter battery. The starter battery will other-
wise be discharged.
iOnly replace a discharged battery with a bat-
tery recommended by Mercedes-Benz. The con-
sumer battery is installed in the trunk in such a
way that it is safeguarded as much as possible
against mechanical destruction in the event of
an accident.
iRemove SmartKey from starter switch (vehi-
cles with KEYLESS-GO*: Make sure the vehicle’s
on-board electronics have status 0)
(
page 336) when you turn off the engine and
no longer require any electrical consumers. The
vehicle then uses very little power and the con-
sumer battery is spared.
iIf the consumer battery is discharged, you
must use the mechanical key to unlock the vehi-
cle (
page 635). Since the vehicle has a sepa-
rate starter battery, however, you can still start
the vehicle.
!Always disconnect the starter battery in the
order described below. You could otherwise
damage the vehicle’s electronics.
!Switch off the vehicle’s internal electrical
functions before disconnecting the starter bat-
tery. If the vehicle is stationary for more than one
hour with the SmartKey removed, you do not
need to switch off the vehicle’s internal electrical
functions.
ProCarManuals.com

663 Practical hints
Towing the vehicle
Towing the vehicle
Mercedes-Benz recommends that the
vehicle be transported with all wheels off
the ground using flatbed or appropriate
wheel lift/dolly equipment. This method is
preferable to other types of towing.
When circumstances do not permit the
recommended towing methods, the
vehicle may be towed with all wheels on
the ground or front axle raised only so far
as necessary to have the vehicle moved to
a safe location where the recommended
towing methods can be employed.
!Do not tow-start the vehicle.
!Use flatbed or wheel lift/dolly equipment
with SmartKey or SmartKey with KEYLESS-GO*
in starter switch turned to position0.
Do not tow with sling-type equipment. Towing
with sling-type equipment over bumpy roads will
damage radiator and supports.
Towing of the vehicle should only be done using
the properly installed towing eye bolt. Never at-
tach tow cable, tow rope, or tow rod, to vehicle
chassis, frame, or suspension parts.
Switch off the ESP
® (page 71), the tow-away
alarm (
page 78) and the automatic central
locking (
page 334).
Warning!G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:

the engine will not run

there is a malfunction in the brake
system

there is a malfunction in the power
supply or in the vehicle’s electrical
system
as that will be necessary to adequately
control the towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make sure the SmartKey or
SmartKey with KEYLESS-GO* is in starter
switch position 2.
ProCarManuals.com

665 Practical hints
Towing the vehicle
If you want the gear position to remain in
neutral position N, observe the following
instructions.
Vehicles with SmartKey:
With the vehicle at a standstill and the
ignition switched on shift the
automatic transmission to neutral
positionN.
If engaged, manually release the elec-
tronic parking brake (
page 385).
Switch off the ignition and leave the
SmartKey in the starter switch.Vehicles with KEYLESS-GO*:
With the vehicle at a standstill, depress
the brake pedal and keep it pressed.
With the ignition switched on shift the
automatic transmission to park
positionP.
Release the brake pedal.
Remove the KEYLESS-GO start/stop
button from the starter switch
(
page 337).
Insert the SmartKey with KEYLESS-GO
into the starter switch.
Switch on the ignition.
Depress the brake pedal.
Shift the automatic transmission to
neutral positionN.
Release the brake pedal.
If engaged, manually release the
electronic parking brake (
page 385).
Switch off the ignition and leave the
SmartKey with KEYLESS-GO in the
starter switch.
Warning!G
When leaving the SmartKey or SmartKey
with KEYLESS-GO* in the starter switch, do
not leave children unattended in the vehicle.
It is possible for children to switch on the
ignition which could result in unsupervised
use of vehicle equipment. Unsupervised use
of vehicle equipment could result in an
accident and/or serious personal injury.
iWhen towing the vehicle with all wheels on
the ground, please note the following:
With the automatic central locking activated and
the SmartKey or SmartKey with KEYLESS-GO* in
starter switch position 2, the vehicle doors lock
if the left front wheel as well as the right rear
wheel are turning at vehicle speeds of approxi-
mately 9mph (15km/h) or more.
To prevent the vehicle doors from locking,
deactivate the automatic central locking
(
page 334).
iTo signal turns while being towed with the
hazard warning flasher in use, turn SmartKey or
SmartKey with KEYLESS-GO* in starter switch to
position2 and activate the combination switch
for the left or right turn signal in the usual
manner – only the selected turn signal will
operate.
Upon canceling the turn signal, the hazard
warning flasher will operate again.
ProCarManuals.com

666 Practical hints
Towing the vehicle
Installing towing eye bolt
1Cover on right side of front bumper
1Cover on right side of rear bumperRemoving cover
Press mark on cover1 in the direction
of arrow.
Lift cover off to reveal the threaded
hole for towing eye bolt.
Installing towing eye bolt
Take towing eye bolt and wheel wrench
out of the vehicle tool kit in the trunk
(
page 632).
Screw towing eye bolt clockwise into
its stop and tighten with wheel wrench.Removing towing eye bolt
Loosen towing eye bolt counterclock-
wise with wheel wrench.
Unscrew towing eye bolt.
Store towing eye bolt and wheel
wrench in the vehicle tool kit in the
trunk.
Installing cover
Fit cover1 and snap into place.
ProCarManuals.com

694 Index
Audio (COMAND) 107
CD mode 115
DVD mode 115
MP3 mode 115
Audio (Control system
instrument cluster) 263
CD changer 264
DVD changer 264
Audio DVD
Fast forward/rewind (COMAND) 117
Menu overview (COMAND) 114
Pause function (COMAND) 116
Stop function (COMAND) 116
Auto-dimming, Rear view mirrors 355Automatic climate control 453
Adjusting air distribution
(COMAND) 246
Adjusting air flow from air vents
(COMAND) 249
Adjusting air volume
(COMAND) 246
Adjusting the footwell temperature
(COMAND) 249
Air recirculation mode 458
Central climate control menu
(COMAND) 247
Defrosting 456
Operating via COMAND 244
Rear window defroster 457
Selecting Mono mode
(COMAND) 248
Setting temperature
(COMAND) 245
Setting the temperature 456
Switching cooling on or off
(COMAND) 247Automatic headlamp mode 271, 364
Automatic lighting control,
Interior lighting 370
Automatic locking when driving 334
Automatic shift program 399
Automatic transmission
Accelerator position 396
Automatic shift program 399
Emergency operation
(limp-home mode) 401
Fluid 684
Fluid level 517
Gear ranges 398
Gear selector lever 389
Gear shifting malfunctions 401
Hill start assist system 397
Kickdown 396
Program mode selector switch 399
Shifting procedure 392
Starting the engine 378
Steering wheel gearshift control 400
Transmission fluid 517
Transmission positions 393
ProCarManuals.com

695 Index
B
Backup lamps
Replacing bulbs 642
Bar 545
BAS 66
Batteries, SmartKey
Checking battery condition 332
Replacing 639
Batteries, SmartKey with KEYLESS-GO*
Checking battery condition 332
Replacing 639
Batteries, vehicle 655
Charging 658
Discharged, Jump starting 660
Disconnecting 657
For electrical consumers 655
For starter 655
Message in display 608
Reconnecting 659
Removing 658
Bead 545
Beverage holder see Cup holder
Bluetooth
®
Settings (COMAND) 232
Brake assist system (BAS Plus) 67
Brake assist system (BAS) 66Brake fluid 511, 685, 687
Brake lamp bulbs 642
Brake lamp, high mounted 642
Brake pads
Message in display 598
Brake warning lamp 31
Brakes 500
Warning lamp 31, 567
Break-in period 498
Bulbs, replacing 641
Additional turn signals 642
Brake lamps 642
Fog lamps 642
Front lamps 642
High beam 642
High mounted brake lamp 642
License plate lamps 642
Low beam 642
Parking and standing lamps 642
Rear fog lamp 642
Turn signal lamps 642C
California retail buyers and lessees,
important notice for 15
Can holder see Cup holder
Capacities and
recommended fuel/lubricants 684
Carpets, Cleaning and care of 564
Catalytic converter 507
CD
Ejecting (COMAND) 113
Loading (COMAND) 111
Menu overview (COMAND) 114
Playback options (COMAND) 119
Selecting a medium (COMAND) 117
Selecting a track (COMAND) 117
CD (COMAND) 107
Central locking
Automatic 334
Locking/unlocking from inside 335
Central locking/unlocking switches 335
Certification label 674
Change of address or ownership 16
ProCarManuals.com