warning MERCEDES-BENZ CL-CLASS 2007 Owners Manual

433 Controls in detail
Driving systems
Warning indicators
Visual signals indicate to the driver the rel-
ative distance between the sensors and an
obstacle.
The warning indicator for the front area is
in the instrument cluster. The warning indi-
cator for the rear area is on the roof liner in
the rear.
1Left side of the vehicle
2Right side of the vehicle
3Readiness indicators
Each warning indicator is divided into five
yellow and two red distance segments for
either side of the vehicle.
If yellow readiness indicators 3 under the
distance segments are lit, Parktronic is
ready to measure.The position of the gear selector lever de-
termines which warning indicators will be
activated.
As your vehicle approaches an object, one
or more distance segments will illuminate,
depending on the distance. When the sev-
enth distance segment illuminates, you
have reached the minimum distance.
Front area:
An intermittent acoustic warning will
sound as the first red distance segment
illuminates and a constant acoustic
warning lasting a maximum of
2 seconds will sound for the second
red distance segment. The signal is
canceled when the gear selector lever
is placed in position P.

Rear area:
An intermittent acoustic warning will
sound as the first red distance segment
illuminates and a constant acoustic
warning lasting a maximum of
2 seconds will sound for the second
red distance segment. The signal is
canceled when the gear selector lever
is placed in position D orP.
Gear selector
lever positionWarning indicator
DFront area activated
RFront and rear area
activated
NWith the electronic
parking brake engaged:
neither activated.
With the electronic
parking brake released:
front and rear area
activated.
PNeither activated
ProCarManuals.com

434 Controls in detail
Driving systems
Switching Parktronic system on/off
The Parktronic system can be switched off
manually.
1Parktronic button
2Indicator lampSwitching off the Parktronic sys-
tem: Press button 1.
Indicator lamp 2 comes on.
Switching on the Parktronic system:
Press button 1 again.
Indicator lamp 2 goes out.
Parktronic system malfunction
If only the red distance segments illumi-
nate and an acoustic warning sounds,
there is a malfunction in the Parktronic
system. The Parktronic system will auto-
matically switch off after 20 seconds and
the indicator lamp in the Parktronic switch
comes on.
Have the Parktronic system checked
by an authorized Mercedes-Benz
Center as soon as possible.
If only the red distance segments illumi-
nate and no acoustic warning sounds, the
Parktronic system sensors are dirty or
there is an interference from other radio or
ultrasonic signals. The Parktronic system
will automatically switch off after 20 sec-
onds and the indicator lamp in the
Parktronic switch comes on.
Switch off the ignition (page 336).
Clean the Parktronic system sensors
(
page 559).
Switch on the ignition.
or
Check the Parktronic system operation
at another location to rule out interfer-
ence from outside radio or ultrasonic
signals.
iThe Parktronic system is automatically
switched on when the ignition is switched on
(
page 336).
ProCarManuals.com

435 Controls in detail
Driving systems
Park Assist*
Park Assist is an electronic parking aid
with radar sensors that helps you while
parking.
Warning!G
Park Assist is a supplemental system. It is
not intended to, nor does it replace, the
need for extreme care. The responsibility
during parking and other critical maneuvers
always remains with the driver.
Warning!G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.
!Special attention must be paid to objects
with smooth surfaces or low silhouettes (e.g.
trailer couplings, painted posts, elevated cross-
bars or road curbs). Such objects may not be
detected by the system and can damage the
vehicle.
iUSA only:
This device has been approved by the FCC as a
“Vehicular Radar System”. The radar sensor is
intended for use in an automotive radar system
only. Removal, tampering, or altering of the de-
vice will void any warranties, and is not permitted
by the FCC. Do not tamper with, alter, or use in
any non-approved way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
iCanada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation of the device.
Removal, tampering, or altering of the device will
void any warranties, and is not permitted. Do not
tamper with, alter, or use in any non-approved
way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
!The operational function of the Park Assist
system can be affected by dirty sensors, espe-
cially at times of snow and ice.
Make sure that the area on the bumpers around
the sensors is free of dirt, ice and/or slush,
otherwise Park Assist may not function properly,
see “Cleaning the Park Assist* system sensors”
(
page 559).
!High-frequency sources such as toll sta-
tions, speed measuring systems, etc. can cause
the Park Assist system to malfunction. You can
switch off the Park Assist using the Park Assist
button (
page 438) or switch off the radar sen-
sors (
page 272) to prevent possible malfunc-
tion.
ProCarManuals.com

437 Controls in detail
Driving systems
Front sensors
Rear sensorsWarning indicators
Visual signals indicate to the driver the rel-
ative distance between the sensors and an
obstacle.
The warning indicator for the front area is
in the instrument cluster. The warning indi-
cator for the rear area is on the roof liner in
the rear.
1Left side of the vehicle
2Right side of the vehicle
3Readiness indicator
Each warning indicator is divided into five
yellow and two red distance segments for
either side of the vehicle.
If yellow readiness indicators 3 under the
distance segments are lit, Park Assist is
ready to measure.The position of the gear selector lever de-
termines which warning indicators will be
activated.
As your vehicle approaches an object, one
or more distance segments will illuminate,
depending on the distance. When the sev-
enth distance segment illuminates, you
have reached the minimum distance.
iDue to the sensors’ broad detection range,
it is possible that Park Assist also detects the fol-
lowing obstacles and issues a warning:

obstacles in the ground, e.g. sewer canal
covers, rails, bumps in the road or gutters

obstacles moving upward quickly, e.g. rolling
garage doors
Centerapprox. 40 in (100 cm)
Cornersapprox. 24 in (60 cm)
Centerapprox. 50 in (125 cm)
Cornersapprox. 24 in (60 cm)
!While parking, pay particular attention to ob-
jects over or underneath the sensors, e.g. flower
boxes, an elevated crossbar or a trailer tow
hitch. Park Assist does not detect such nearby
objects. You could otherwise damage the vehicle
or the objects.
Gear selector
lever positionWarning indicator
DFront area activated
RFront and rear area
activated
NWith the electronic
parking brake engaged:
neither activated.
With the electronic
parking brake released:
front and rear area acti-
vated.
PNeither activated
ProCarManuals.com

438 Controls in detail
Driving systems

Front area:
As soon as the first red distance seg-
ment comes on, you will hear an inter-
mittent warning tone for approximately
2 seconds. Once the second red dis-
tance segment comes on, you will hear
a continuous warning tone. You have
reached the minimum distance.

Rear area:
As soon as the first red distance seg-
ment comes on, you will hear an inter-
mittent warning tone for approximately
2 seconds. Once the second red dis-
tance segment comes on, you will hear
a continuous warning tone. You have
reached the minimum distance.Collision warning
Park Assist can detect obstacles from a
considerable distance. If you drive in re-
verse towards an obstacle, you will hear a
warning tone. You must then brake in or-
der to avoid a collision. The warning tone
for a collision will not sound when the vehi-
cle is at a standstill very close to the obsta-
cle. In this case, you will hear a
corresponding tone for the warning indica-
tor in the rear area.
Switching Park Assist system on/off
The Park Assist system can be switched off
manually.
The Park Assist button with the indicator
lamp is located on the control panel on the
right-hand side of the instrument cluster.1Park Assist button
2Indicator lamp
Switching off Park Assist system:
Press button 1.
Indicator lamp 2 comes on.
Switching on Park Assist system:
Press button 1 again.
Indicator lamp 2 goes out.iDuring strong rainfall, the warning indicators
and warning tones may be triggered, for exam-
ple, by water splashing into the area of the sen-
sors.
iDuring strong rainfall, the collision warning
may be triggered, for example, by water splash-
ing into the area of the sensors.
iWhen the indicator lamp is illuminated, the
Park Assist system is switched off.
iThe Park Assist system is automatically
switched on when the ignition (
page 336) and
radar sensors are switched on (
page 272).
ProCarManuals.com

440 Controls in detail
Driving systems
Warning!G
Please note that objects which do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck, may appear to be further
away than they actually are. In this case, you
should not use the guide lines to judge dis-
tance. The use of the guide lines to judge
distance increases the risk of impacting the
objects.
Warning!G
The Dynamic Rear View Monitor is a supple-
ment system. It is not intended to, nor does
it replace, the need for extreme care. The re-
sponsibility during parking and other driving
maneuvers always remains with the driver.
The Dynamic Rear View Monitor may show
obstacles with a distorted perspective, in-
correctly or not at all.
Special attention must be paid to objects
outside of the camera’s field of view such as
those located very close to or below the rear
bumper, or above the recessed grip of the
luggage compartment lid. Such objects may
not be detected by the system and can dam-
age the vehicle.
The Dynamic Rear View Monitor does not
warn you about impending collisions with
objects. The driver is always responsible for
safety and must continue to pay attention to
the immediate surroundings while parking
or maneuvering the vehicle. This applies not
only to the area behind the vehicle, but also
to the area in front of and to the sides of the
v e h i c l e . F a i l u r e t o d o s o c o u l d r e s u l t i n i n j u r y
to persons and/or damage to the vehicle or
other property. We also recommend that the
driver use the Parktronic system* or Park
Assist* when parking or maneuvering the
vehicle.Warning!G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.
Warning!G
The Dynamic Rear View Monitor may not
function if:

the trunk lid is not completely closed

it is raining or snowing heavily, or if
there is thick fog

in a very dark area

the camera is exposed to very strong
white light (white stripes may appear on
the COMAND display)

the surrounding area is lit with fluores-
cent light (the COMAND display can
flicker)

outside temperatures are very high (lens
condensation)
ProCarManuals.com

441 Controls in detail
Driving systems
Switching on Dynamic Rear View Moni-
tor
Switch on the ignition (page 336).
Switch on COMAND (page 81).
Move gear selector lever to position R
(reverse gear).
The COMAND display will show the
area behind the vehicle with guide lines
to help you reverse into a parking
place.Reverse parking (back-in parking)
This function helps you when you are re-
versing in a straight line or backing in at
any angle.
The space required by the vehicle for re-
versing is shown by guide lines.
When you turn the steering wheel to a
straight-ahead position, you will see the
guide lines on the COMAND display in the
following order:

there is a sudden change in tempera-
ture, for example when you drive out of
the cold into a heated garage in winter
(lens condensation)

the camera lens is dirty or covered, see
“Cleaning the Dynamic Rear View
Monitor lens*” (
page 560)

the rear of your vehicle is damaged. In
this case, have the position and setting
of the camera checked by a qualified
technician. Contact an authorized
Mercedes-Benz Center.
Do not use the Dynamic Rear View Monitor
if the roads are icy, slippery or covered with
snow. The vehicle could slip causing the ac-
tual vehicle position to deviate from the one
shown on the COMAND display.
This may cause injury to you or others, or
damage the vehicle or objects.
Mounting tires/rims of other specification
than the original equipment tires/rims may
impair the function of the Dynamic Rear
View Monitor. Contact an authorized
Mercedes-Benz Center.
Warning!G
Use of Dynamic Rear View Monitor can be
dangerous if you are color-blind or have im-
paired color vision.
Only use Dynamic Rear View Monitor if you
can see and distinguish all colored guide
lines shown by Dynamic Rear View Monitor
on the COMAND display.
iThe Dynamic Rear View Monitor must be ac-
tivated in the instrument cluster control system
in order for it to be switched on (
page 269).
iIf you activate a different function on the
driver’s COMAND controls while reverse parking
or parallel parking, the image from the back-up
camera is interrupted.
To reactivate the camera, take the vehicle out of
reverse gear and then re-engage reverse gear
again.
ProCarManuals.com

442 Controls in detail
Driving systems
1Yellow and blue guide lines for vehicle
width
2Yellow 13 ft (4 m) guide line
3Yellow 39 in (1 m) guide line
4Red 10 in (0.25 m) guide line
The red 10 in (0.25 m) guide line4, the
yellow 39 in (1 m) guide line3 and the
y e l l o w 1 3 f t ( 4 m ) g u i d e l i n e2 correspond
to the relevant distance from the rear of
the vehicle. The yellow and blue guide lines
for vehicle width1 show the required
width for the vehicle.5Blue guide lines for straight driving
6Symbol for “reverse parking”
7Yellow and red guide lines for cornering
When you turn the steering wheel out of
the straight-ahead position, the positions
of the yellow and red guide lines7
change depending on the steering wheel’s
position. The space required by the vehicle
for reverse cornering is indicated by yellow
and red guide lines7.
Warning!G
Please note that objects which do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck, may appear to be further
away than they actually are. In this case, you
should not use the guide lines to judge dis-
tance as the use of the guide lines to judge
distance increases the risk of impacting the
objects.
Even when the object you approach is di-
rectly on the ground (and nothing on the ob-
ject extends above the ground beyond the
object’s contours directly touching the
ground) and no objects that do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck are in the path, do not ap-
proach the object on the ground any closer
than red guide line4.
ProCarManuals.com

444 Controls in detail
Driving systems
Stop the vehicle

at a distance of approximately
three feet (one meter) parallel to
the vehicle that is in front of the de-
sired parking space.

in such a way that the front of the
parked vehicle is parallel to your
rear wheel.
Switch on COMAND (page 81).
Move gear selector lever to position R
(reverse gear).
1Vertical blue guide line
2Symbol for “parallel parking”
Use the COMAND controller
(
page 84) to select “parallel parking”
function2.
You will see the guide lines for parallel
parking on the COMAND display.
Back up carefully parallel to parked car
until the respective vertical blue guide
line1 is at the end of the parked vehi-
cle next to you.
Stop the vehicle.1Vertical blue guide line
3Extended blue guide line
4Blue guide lines for vehicle contour
With the vehicle at a standstill, turn
steering wheel in parking direction until
blue guide lines3 and 1 appear and
the rectangle formed by guide lines 4
shows the desired parking position. If
another vehicle is located next to you,
the extended blue guide line3 must
just touch the corresponding vertical
blue guide line1.Warning!G
If the respective vertical blue guide line1
is not yet located at the end of the parked
vehicle and you are already turning into the
parking space, you could collide with the
parked vehicle. Stop the parking procedure
immediately. Pull out of the parking space
and start the parking procedure over again.
iIf an obstacle is inside of or protrudes into
the area marked by blue guide lines4 for the
vehicle, the parking space is too small for the ve-
hicle.
ProCarManuals.com

445 Controls in detail
Driving systems
5Bent blue guide line
Back up with the set wheel angle.The guide lines in the COMAND display
disappear. After a short distance, the
bent blue guide line5 appears.
Back up until bent guide line5 inter-
sects the edge of the parking space,
e.g. the curb.
Stop the vehicle.
6Yellow and red guide lines for cornering
7Blue guide line for straight driving
With the vehicle at a standstill, turn
steering wheel as far as it will go in the
opposite direction.
The guide lines for straight driving7
and cornering6 appear in the
COMAND display.
Back up using the set wheel angle until
blue guide line7 for straight driving is
parallel to the edge of the parking
space, e.g. the curb.
Now straighten out steering wheel and
back up until you still have just enough
room behind the vehicle.
While doing so, observe
Parktronic* (
page 431) or Park As-
sist* (
page 435) warning indicators.
iIf you turn the steering wheel too far, the
message “Steering wheel turned too far. Please
adjust steering wheel” appears on the COMAND
display. Turn the steering wheel back until the
message disappears and the extended blue
guide line3 intersects with vertical blue guide
line1.
If you back up using the wrong wheel angle, the
following appears in the COMAND display:
“Steering wheel turned too far. Park Assist dis-
abled.”. Pull out of the parking space and start
the parking procedure over again.
iIf you turn the steering wheel while backing
up, the following appears in the COMAND dis-
play: “The steering wheel position has been
changed. Park Assist disabled.”. Pull out of the
parking space and start the parking procedure
over again.
ProCarManuals.com