check engine MERCEDES-BENZ CL-CLASS 2007 Service Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: CL-CLASS, Model: MERCEDES-BENZ CL-CLASS 2007Pages: 723, PDF Size: 19.87 MB
Page 628 of 723
625 Practical hints
What to do if …?
Display Possible cause/consequencePossible solution
Engine oil level
cannot be
measuredCL 600 only:
The measuring system is malfunctioning.Have the measuring system checked by an
authorized Mercedes-Benz Center.
Engine oil level
Reduce oil levelCL 600:
You have added too much engine oil.
There is a risk of damaging:
the engine
the catalytic converter
Have excess oil siphoned or drained off.
Contact an authorized Mercedes-Benz
Center.
ProCarManuals.com
Page 660 of 723
657 Practical hints
Batteries
Starter battery (example illustration from
CL 550)
1Negative terminal
2Positive terminal
Disconnecting starter battery
Secure vehicle in place with electronic
parking brake (
page 384).
Shift the automatic transmission toP
(
page 389).
Do not rub the battery with rags or cloths.
The battery could explode if touched due to
electrostatic charge or due to spark forma-
tion.
!Switch off the engine and switch off the ve-
hicle’s internal electrical functions (
page 658)
before you disconnect or remove the battery’s
terminal clamps. You could otherwise destroy
electronic assemblies such as the generator.
Have the battery checked regularly by an autho-
rized Mercedes-Benz Center. Refer to Mainte-
nance Booklet for maintenance intervals or
contact an authorized Mercedes-Benz Center for
further information.
!Do not connect any consumers directly to
the starter battery. The starter battery will other-
wise be discharged.
iOnly replace a discharged battery with a bat-
tery recommended by Mercedes-Benz. The con-
sumer battery is installed in the trunk in such a
way that it is safeguarded as much as possible
against mechanical destruction in the event of
an accident.
iRemove SmartKey from starter switch (vehi-
cles with KEYLESS-GO*: Make sure the vehicle’s
on-board electronics have status 0)
(
page 336) when you turn off the engine and
no longer require any electrical consumers. The
vehicle then uses very little power and the con-
sumer battery is spared.
iIf the consumer battery is discharged, you
must use the mechanical key to unlock the vehi-
cle (
page 635). Since the vehicle has a sepa-
rate starter battery, however, you can still start
the vehicle.
!Always disconnect the starter battery in the
order described below. You could otherwise
damage the vehicle’s electronics.
!Switch off the vehicle’s internal electrical
functions before disconnecting the starter bat-
tery. If the vehicle is stationary for more than one
hour with the SmartKey removed, you do not
need to switch off the vehicle’s internal electrical
functions.
ProCarManuals.com
Page 662 of 723
659 Practical hints
Batteries
Starter battery
Connect the switched-off charging de-
vice to the terminals of the starter bat-
tery. Observe the operating
instructions in the manual for the
charging device while doing so.
Reinstalling starter battery
Install starter battery in engine com-
partment.
Swing retaining bar down.
Reconnecting starter battery
Make sure that the consumer battery in
the trunk is correctly installed and con-
nected.
Turn SmartKey in starter switch to po-
sition 0 and remove.
Connect the positive lead and fasten its
cover2 (
page 657).
Connect negative lead1
(
page 657).
Attach ventilation tube.
Switch on the ignition (page 336).
Start the engine (page 378).
Check vehicle functions.
!Only use charging devices with a maximum
charging voltage of 14.8 V.
Warning!G
During the charge procedure, there is a risk
of acid burns due to gases escaping from
the battery. Do not bend over the battery
during the charge procedure.
!The battery and the battery ventilation hose
must always be securely installed when the vehi-
cle is in operation.
!Always connect the starter battery in the or-
der described below. Otherwise, the vehicle’s
electronics could be damaged.
Warning!G
Do not drive without a properly installed and
connected consumer battery.
Have any work on the consumer battery car-
ried out by an authorized Mercedes-Benz
Center.
!Never invert the terminal connections.
!Make sure that the battery has a plug where
the ventilation tube is attached to it.
ProCarManuals.com
Page 663 of 723
660 Practical hints
Jump starting
If the starter battery is discharged, the en-
gine can be started with jumper cables and
the battery of another vehicle. Observe the
following:
Jump starting should only be performed
when the engine and catalytic convert-
er are cold.
Do not start the engine if the battery is
frozen. Let the battery thaw out first.
Only use 12-volt battery to jump start
your vehicle. Jump starting with a high-
er voltage battery could damage the ve-
hicle’s electrical system, which will not
be covered by the Mercedes-Benz Lim-
ited Warranty.
Only use jumper cables with sufficient
cross-section and insulated terminal
clamps.
Always make sure that the jumper ca-
bles are not on or near pulleys, fans or
other parts that move when an engine
is started or running.
Warning!G
Failure to follow these directions will cause
damage to the electronic components, and
can lead to a battery explosion and severe
injury or death.
Never lean over batteries while connecting
or jump starting, you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water, and seek
medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and very explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
Attempting to jump start a frozen battery
can result in it exploding, causing personal
injury.
Read all instructions before proceeding.
!Do not tow-start the vehicle.
!Jump starting should only be performed on
the starter battery installed in the engine com-
partment.
Avoid repeated and lengthy starting attempts.
Do not attempt to start the engine using a bat-
tery quick charge unit.
If engine does not run after several unsuccessful
starting attempts, have it checked at the nearest
authorized Mercedes-Benz Center.
Excessive unburned fuel generated by repeated
failed starting attempts may damage the catalyt-
ic converter and may present a fire risk.
Make sure the jumper cables do not have loose
or missing insulation.
Make sure the cable clamps do not touch any
other metal part while the other end is still at-
tached to a battery.
ProCarManuals.com
Page 665 of 723
662 Practical hints
Jump starting
Remove red cover from positive
terminal4.
Connect positive terminal3 of the
charged battery with positive
terminal4 of the discharged battery
with the jumper cable. Clamp cable to
charged battery3 first.
Connect negative terminal2 of
charged battery to jumper cables and
attach other end of the jumper cable
with the negative clamp1 to a suit-
able ground point on the vehicle.
Get into vehicle and start engine within
30 seconds.
If the starting attempt does not suc-
ceed:
Turn the SmartKey in starter switch
to position 0.
Take out the SmartKey.
Turn off engine of donor vehicle, re-
start it and let it run at idle speed
for several minutes.
Disconnect the jumper cable during
this time.
Reconnect jumper cable as de-
scribed before.
Restart engine.
While the engine is running, switch off
several electrical consumers such as
the blower.
Disconnect jumper cables first nega-
tive clamp1 from ground point and
negative terminal2, then from posi-
tive terminals4 and3.
Have the battery checked at the near-
est authorized Mercedes-Benz Center.!Never invert the terminal connections.
ProCarManuals.com
Page 692 of 723
689 Technical data
Fuels, coolants, lubricants, etc.
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which pro-
vides:
Corrosion protection
Freeze protection
Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -35°F (-37°C) and corro-
sion protection.
If the antifreeze mixture is effective to
-35°F (-37°C), the boiling point of the cool-
ant in the pressurized cooling system is
reached at approximately 266°F (130°C).The coolant solution must be used year
round to provide the necessary corrosion
protection and increase boil-over protec-
tion. Refer to Maintenance Booklet for re-
placement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance Booklet is only applicable if
MB 325.0 Anticorrosion/Antifreeze solu-
tion or other Mercedes-Benz approved
products of equal specification are used to
renew the coolant concentration or bring it
back up to the proper level.
For information on other Mercedes-Benz
approved products of equal specification,
refer to the Factory Approved Service
Products pamphlet (USA only) or contact
an authorized Mercedes-Benz Center.To provide important corrosion protection,
the solution must be at least 50% anticor-
rosion/antifreeze (equivalent to freeze
protection to approximately -35°F
[-37°C]). If you use a solution that is more
than 55% anticorrosion/antifreeze (freeze
protection to approximately -49°F
[-45°C]), the engine temperature will in-
crease due to the lower heat transfer capa-
bility of the solution. Therefore, do not use
more than this amount of anticorrosion/
antifreeze.
If the coolant level is low, water and
MB 325.0 Anticorrosion/Antifreeze
should be used to bring it up to the proper
level (have cooling system checked for
signs of leakage).
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality, con-
sult an authorized Mercedes-Benz Center.
!Add premixed coolant solution only. Adding
water and MB 325.0 Anticorrosion/Antifreeze
separately from each other, could cause engine
damage not covered by the Mercedes-Benz Lim-
ited Warranty.
ProCarManuals.com
Page 693 of 723
690 Technical data
Fuels, coolants, lubricants, etc.
Anticorrosion/antifreeze
Your vehicle contains a number of alumi-
num parts. The use of aluminum compo-
nents in motor vehicle engines
necessitates that anticorrosion/antifreeze
coolant used in such engines be specifical-
ly formulated to protect the aluminum parts. Failure to use such anticorrosion/
antifreeze coolant will result in a signifi-
cantly shortened service life.
Therefore, the following product is strongly
recommended for use in your vehicle:
MB 325.0 Anticorrosion/Antifreeze agent.Before the start of the winter season (or
once a year in hot southern regions), you
should have the anticorrosion/antifreeze
concentration checked. The coolant is also
regularly checked each time you bring your
vehicle to an authorized Mercedes-Benz
Center for service.
Anticorrosion/antifreeze quantity
ModelApproximate freeze protection
-35°F (-37°C)-49°F (-45°C)
CL 5506.08 US qt. (5.75 l)6.71 US qt. (6.35 l)
CL 600 (main cooling system)6.5 US qt. (6.15 l)7.14 US qt. (6.76 l)
CL 600 (low temperature cooling system)1.37 US qt. (1.3 l)1.51 US qt. (1.43 l)
ProCarManuals.com
Page 703 of 723
700 Index
Emergency operations
Locking the vehicle 635
Mechanically releasing
the electronic parking brake 637
Releasing from inside 464
Remote door lock 489
Remote door unlock 489
Tilt/sliding sunroof 638
Unlocking the trunk 636
Unlocking the vehicle 635
Emergency Tensioning Device see ETD
Emergency, In case of
Battery, Jump starting 660
First aid kit 632
Flat tire 649
Fuses 667
Roadside Assistance 16
Roadside Assistance (Tele Aid) 485
Towing the vehicle 663
Emission control 507
Emission control information label 675
Emission control system warranties 14Engine
Belt layout 676
Cleaning 556
Compartment 512
Coolant 518, 685, 689
Malfunction indicator lamp 31, 570
Number 674, 675
Oil 516, 684, 686
Oils 513
Residual heat and ventilation 460
Starting 378
Technical data 677
Turning off 387
Engine coolant see Coolant
Engine oil 513
Adding 516
Additives 686
Checking level 513
Checking level (Dipstick) 516
Checking level (Instrument
cluster control system) 514
Consumption 513Dipstick 516
Filler neck 516, 517
Messages in display 515, 623
Recommended engine oils
and oil filters 684
ESP
®69
Messages in display 594, 605
Warning lamp 31, 567, 572
ETD 55
Safety guidelines 44
Exterior lighting
Delayed switch-off (COMAND) 235
Locator lighting (COMAND) 236
Exterior rear view mirrors
Adjusting 353
Auto-dimming
on the driver’s side 355
Fold in automatically when locking
(COMAND) 237
Lower mirror when reversing
(COMAND) 237
Power folding 354
ProCarManuals.com
Page 706 of 723
703 Index
I
Identification labels 674
Identification Number, Vehicle (VIN) 675
Ignition 336, 338
Switching on 336
Switching on, KEYLESS-GO* 338
Immobilizer 77
Indicator lamps see
Lamps, indicator and warning
Individualization
Voice Control 320
Infant and child restraint systems
see Children in the vehicle
Infrared reflecting windshield 496
Inside door handle 333
Instrument cluster 30, 402
Coolant temperature gauge 31, 403
Fuel gauge 31
Illumination 402, 448
Lamps 566
Multifunction display 256
Outside temperature indicator 404
Selecting the language
(COMAND) 231Interior lighting 369
Activating automatic control 370
Ambient lighting (COMAND) 240
Deactivating automatic control 370
Delayed switch-off (COMAND) 241
Reading lamps in the front 370
Interior rear view mirror
Adjusting 353
Auto-dimming 355
Interior storage spaces see
Storage compartments
J
Jack 633, 650
Jacking up the vehicle 650
Jump starting 660K
Key, Mechanical 635
Loss of 332
Key, SmartKey 322
Battery check lamp 322, 325
Factory setting 324
Global locking and unlocking 324
Lock button 322
Locking and unlocking 322
Loss of 332
Messages in display 615
Opening button for trunk 322
Panic button 63
Remote control 322
Restoring to factory setting 325
Selective setting 325
Starting the engine 379
Switching on ignition with 336
Turning off engine 387
Unlock button 322
ProCarManuals.com
Page 707 of 723
704 Index
Key, SmartKey with KEYLESS-GO* 326
Battery check lamp 326, 330
Factory setting 329
Global locking and unlocking 330
Important notes
on using KEYLESS-GO* 328
Lock button 326
Locking and unlocking 326
Locking using the lock button
on door or on trunk lid 331
Loss of 332
Messages in display 614
Opening button for trunk 326
Panic button 63
Remote control 326
Restoring to factory setting 331
Selective setting 330
Starting the engine 379
Switching on ignition with 338
Turning off engine 388
Unlock button 326
Kickdown 396
Kilopascal 545
Knee bag 46L
Labels 674
Certification 674
Emission control information 675
Tire and Loading Information 524
Vacuum line routing diagram 675
Lamp bulbs, exterior 641
Lamps, exterior
Front 642
Light sensor 617
Rear 642
Lamps, indicator and warning
ABS 31, 64, 566
Air bag Off 46
Battery check lamp (SmartKey
with KEYLESS-GO*) 330
Battery check lamp (SmartKey) 325
Brake warning lamp 31
Brakes 567
Combination low tire pressure*
malfunction telltale 31, 576
Distance warning lamp* 31, 572
DISTRONIC Plus* 31, 414, 572
Electronic parking brake 31, 568
Engine diagnostics 31, 570
Engine malfunction 31, 570ESP®31, 567, 572
Front passenger front
air bag off 50, 578
Fuel reserve 573
High beam headlamp 31
Maintenance service indicator 551
Park Assist* 31
Parktronic* 31
Seat belt telltale 31, 573
SRS 31, 575
TPMS* malfunction telltale 31, 576
Turn signals 31
Language (COMAND) 231
LATCH-type child seat anchors
see Children in the vehicle
Lever
For automatic transmission
(gear selector lever) 389
For cruise control 406
For DISTRONIC Plus* 417
License plate lamps
Messages in display 619
Replacing bulbs 642
Light alloy wheels, Cleaning 563
ProCarManuals.com