warning MERCEDES-BENZ CL-Class 2008 C216 Comand Manual

467 Controls in detail
Driving systems

Switching off the Parktronic sys-
tem: Press button 1.
Indicator lamp 2 comes on.

Switching on the Parktronic system:
Press button 1 again.
Indicator lamp 2 goes out.
Parktronic system malfunction
If only the red distance segments illumi-
nate and an acoustic warning sounds,
there is a malfunction in the Parktronic
system. The Parktronic system will auto-
matically switch off after 20 seconds and
the indicator lamp in the Parktronic switch
comes on.

Have the Parktronic system checked
by an authorized Mercedes-Benz
Center as soon as possible.
If only the red distance segments illumi-
nate and no acoustic warning sounds, the
Parktronic system sensors are dirty or
there is an interference from other radio or
ultrasonic signals. The Parktronic system
will automatically switch off after 20 sec-
onds and the indicator lamp in the
Parktronic switch comes on.

Switch off the ignition (
page 365).

Clean the Parktronic system sensors
(page 600).

Switch on the ignition.
or

Check the Parktronic system operation
at another location to rule out interfer-
ence from outside radio or ultrasonic
signals.
Park Assist*
i
The Parktronic system is automatically
switched on when the ignition is switched on
(
page 365).
Warning!
G
Park Assist is a supplemental system. It is
not intended to, nor does it replace, the
need for extreme care. The responsibility
during parking and other critical maneuvers
always remains with the driver.Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.!
Special attention must be paid to objects
with smooth surfaces or low silhouettes (e.g.
trailer couplings, painted posts, elevated cross-
bars or road curbs). Such objects may not be
detected by the system and can damage the
vehicle.

469 Controls in detail
Driving systems
The Park Assist system deactivates at
speeds over approximately 10 mph
(16 km/h). At lower speeds the Parktronic
system turns on again.
Park Assist is also switched off when you
set the automatic transmission to park
positionP or switch off the engine.
While the transmission is in neutral
positionN, Park Assist is switched off if
you secure the vehicle in place with the
electronic.
The Park Assist system monitors the sur-
roundings of your vehicle with four sensors
in the front bumper and two sensors in the
rear bumper.
Range of the sensors
The sensors of the Park Assist system are
integrated in the front and rear bumpers.
Make sure that the bumpers are clear of
dirt, ice and slush in the area of the sen-
sors, as otherwise, Park Assist may not
function properly, see “Cleaning the driv-
ing systems sensors” (
page 601).Front sensors
Rear sensors
i
Due to the sensors’ broad detection range,
it is possible that Park Assist also detects the fol-
lowing obstacles and issues a warning:


obstacles in the ground, e.g. sewer canal
covers, rails, bumps in the road or gutters


obstacles moving upward quickly, e.g. rolling
garage doors
Center
approx. 40 in (100 cm)
Corners
approx. 24 in (60 cm)
Center
approx. 50 in (125 cm)
Corners
approx. 24 in (60 cm)
!
While parking, pay particular attention to ob-
jects over or underneath the sensors, e.g. flower
boxes, an elevated crossbar or a trailer tow
hitch. Park Assist does not detect such nearby
objects. You could otherwise damage the vehicle
or the objects.

470 Controls in detailDriving systemsWarning indicators
Visual signals indicate to the driver the rel-
ative distance between the sensors and an
obstacle.
The warning indicator for the front area is
in the instrument cluster. The warning indi-
cator for the rear area is on the roof liner in
the rear.
1Left side of the vehicle
2Right side of the vehicle
3Readiness indicator
Each warning indicator is divided into five
yellow and two red distance segments for
either side of the vehicle.
If yellow readiness indicators 3 under the
distance segments are lit, Park Assist is
ready to measure.The position of the gear selector lever de-
termines which warning indicators will be
activated.
As your vehicle approaches an object, one
or more distance segments will illuminate,
depending on the distance. When the sev-
enth distance segment illuminates, you
have reached the minimum distance.


Front area:
As soon as the first red distance seg-
ment comes on, you will hear an inter-
mittent warning tone for approximately
2 seconds. Once the second red dis-
tance segment comes on, you will hear
a continuous warning tone. You have
reached the minimum distance.


Rear area:
As soon as the first red distance seg-
ment comes on, you will hear an inter-
mittent warning tone for approximately
2 seconds. Once the second red dis-
tance segment comes on, you will hear
a continuous warning tone. You have
reached the minimum distance.
Gear selector
lever position
Warning indicator
D
Front area activated
R
Front and rear area
activated
N
With the electronic
parking brake engaged:
neither activated.
With the electronic
parking brake released:
front and rear area acti-
vated.
P
Neither activated
i
During strong rainfall, the warning indicators
and warning tones may be triggered, for exam-
ple, by water splashing into the area of the sen-
sors.

471 Controls in detail
Driving systems
Collision warning
Park Assist can detect obstacles from a
considerable distance. If you drive in re-
verse towards an obstacle, you will hear a
warning tone. You must then brake in or-
der to avoid a collision. The warning tone
for a collision will not sound when the vehi-
cle is at a standstill very close to the obsta-
cle. In this case, you will hear a
corresponding tone for the warning indica-
tor in the rear area.
Switching Park Assist system on/off
The Park Assist system can be switched off
manually.
The Park Assist button with the indicator
lamp is located on the control panel on the
right-hand side of the instrument cluster.1Park Assist button
2Indicator lamp

Switching off Park Assist system:
Press button 1.
Indicator lamp 2 comes on.

Switching on Park Assist system:
Press button 1 again.
Indicator lamp 2 goes out.
Advanced Parking Guidance*
Advanced Parking Guidance is an electron-
ic parking aid equipped with radar sensors
that scan the area on both sides of vehicle.
When suitable parking space is found it is
shown in the display and you receive steer-
ing instructions for parking in that space.
i
During strong rainfall, the collision warning
may be triggered, for example, by water splash-
ing into the area of the sensors.
i
When the indicator lamp is illuminated, the
Park Assist system is switched off.
i
The Park Assist system is automatically
switched on when the ignition (
page 365) and
radar sensors are switched on (page 302).
Warning!
G
Advanced Parking Guidance is only an aid
and may display parking spaces that are not
suitable e.g. due to parking regulations, un-
suitable road/ground surfaces, driveways,
entrances/exits, etc.


472 Controls in detailDriving systemsAdvanced Parking Guidance only shows a
representation of the parking space in the
instrument cluster display as parking space
is first initially measured when driving past.
Subsequent changes to the parking space
are not taken into account, e.g. if the posi-
tion of the vehicle parked in front of or be-
hind the space changes or objects in the
parking space are moved. Moving objects
are not shown, e.g. pedestrians or vehicles
driving past. Advanced Parking Guidance
does not relieve you of the responsibility to
pay attention. If you only rely on Advanced
Parking Guidance, you may cause an acci-
dent and injure yourself and others.
You are always responsible for safety and
must continue to pay attention to your im-
mediate surroundings when parking and
maneuvering.
Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.!
Special attention must be paid to objects
with smooth surfaces or low silhouettes (e.g.
trailer couplings, painted posts, elevated cross-
bars or road curbs). Such objects may not be de-
tected by the system and can damage the
vehicle.
i
USA only:
This device has been approved by the FCC as a
“Vehicular Radar System”. The radar sensor is
intended for use in an automotive radar system
only. Removal, tampering, or altering of the de-
vice will void any warranties, and is not permitted
by the FCC. Do not tamper with, alter, or use in
any non-approved way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
i
Canada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation of the device.
Removal, tampering, or altering of the device will
void any warranties, and is not permitted. Do not
tamper with, alter, or use in any non-approved
way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
!
The operation and functionality of the Ad-
vanced Parking Guidance* can be affected or im-
paired by dirty sensors, especially at times of
snow and ice.
Make sure that the area on the bumpers around
the sensors is free of dirt, ice and/or slush, oth-
erwise Advanced Parking Guidance* may not
function properly, see “Cleaning the driving sys-
tems sensors” (
page 601).


473 Controls in detail
Driving systems
Use Advanced Parking Guidance for park-
ing spaces that are

parallel to the direction of travel


located on straight streets, i.e. not in
curves


on the same level as the street, i.e. not
on sidewalks, for example. Flat curbs
may possibly not be detected by Ad-
vanced Parking Guidance.
Parking instructions:


On narrow streets, drive by the parking
space as close as possible.


Parking spaces that are dirty, over-
grown or located in front of trailers may
not be detected correctly.


Also observe the Park Assist warning
indicator (
page 470) while Advanced
Parking Guidance is active.


How well your vehicle will be parked af-
ter completion of the Advanced Park-
ing Guidance depends on the position
and shape of the vehicles parked in
front of and behind the parking space
as well as the conditions of the imme-
diate surroundings. In certain cases,
Advanced Parking Guidance may guide
you too far into the parking space or
not far enough. If this is the case, can-
cel the parking procedure with Ad-
vanced Parking Guidance and correct
the vehicle position yourself.Detecting a parking space
Advanced Parking Guidance is active when
driving forward. The system operates at a
vehicle speed of up to 25 mph (40 km/h)
and automatically scans for and measures
potential parking spaces on both sides of
the vehicle. At a vehicle speed of below
10 mph (16 km/h), you see the white
parking space symbol as a system display
in the instrument cluster. As soon as Ad-
vanced Parking Guidance has detected a
suitable parking space, the parking space
symbol changes to blue.

474 Controls in detailDriving systemsDetected parking space1Detected parking spaces on the left
2Parking space symbol
3Detected parking spaces on the right
In order to be detected by Advanced Park-
ing Guidance, a parking space must be:

closed-in at the rear


parallel to the direction of travel


at least 5 ft (1.5 m) wide


at least 3.5 ft (1.0 m) longer than your
vehicleA parking space is shown in the display
when driving by until you have reached a
distance of 50 ft (15 m) from the space.
Advanced Parking Guidance only shows
parking spaces on the front-passenger
side of the vehicle unless you activate the
driver's side (left) turn signal. If you would
like to park on the driver's side, the left
turn signal must remain on until reverse
gear is engaged.Parking
The following describes how you can park
on the front-passenger side. Parking on
the driver's side is performed reversed left
to right.
If Advanced Parking Guidance detects an
obstacle behind the vehicle during the
parking procedure, you will hear an audible
warning. Stop the vehicle immediately. The
parking space and the lane blink in the in-
strument cluster. Only continue driv-
ing/parking after you have made sure that
this is possible to do in a safe manner. If
Advanced Parking Guidance no longer de-
tects any obstacles, the display in the in-
strument cluster stops blinking. You may
continue the parking procedure.

475 Controls in detail
Driving systems

Bring the vehicle to a standstill as long
as the desired parking space is dis-
played by the blue parking space sym-
bol in the instrument cluster.

Shift the automatic transmission to
positionR.
The message “Check Surroundings
Press 'OK' to Confirm” appears in the
multifunction display.

Press# on the multifunction steer-
ing wheel to confirm.
The display in the instrument cluster
changes to the Advanced Parking Guid-
ance.
1Green lane
2White bracket indicates the stopping
position

Where necessary, depending on the
distance to the parking space, back up
in a straight line a short distance.
This is indicated by a green lane1.

Back up until you hear an audible warn-
ing, then stop.
The stopping position has been
reached, indicated by a white
bracket2.
3Red lane indicates the current steering
wheel position
4Yellow lane indicates the required
steering wheel position

When the vehicle is stationary, turn the
steering wheel until the red lane3
matches up with the yellow lane4.
Warning!
G
Advanced Parking Guidance is only an aid
and may not detect all obstacles. At corners
or near smooth surfaces, Advanced Parking
Guidance may not detect an object correct-
ly. Advanced Parking Guidance does not re-
lieve you of the responsibility to pay
attention. You are always responsible for
safety and must continue to pay attention to
your immediate surroundings when parking
and maneuvering. Otherwise, you could en-
danger yourself and others.


476 Controls in detailDriving systems
The lane4 then turns green. If the
parking space is located within the dis-
play range, a white bracket with an ar-
row for the target position is shown at
the end of the green lane.
Driving into the parking space
1Green lane indicates the correct steer-
ing wheel position

Maintain the steering wheel position
and carefully back up.

Stop as soon as you hear the audible
warning.
The vehicle has reached the position
for countersteering.Countersteering
1Red lane indicates the current steering
wheel position
2Yellow lane indicates the required
steering wheel position

When the vehicle is stationary, turn the
steering wheel until the red lane1
matches up with the yellow lane2.
The lane2 then turns green and a
white arrow and a white bracket are
shown to indicate the target position.Reaching end position
1Green lane indicates the correct steer-
ing wheel position

Maintain the steering wheel position
and carefully back up until the end po-
sition has been reached.
The message appears “Parking Guid-
ance Finished” in the multifunction dis-
play and you will hear an audible
warning.
If the distance to the rear is too short,
you will also be audibly warned by the
Park Assist* system (
page 467).


478 Controls in detailDriving systemsThe Rear View Camera is in the handle
strip of the trunk lid.
1Rear View CameraView through the camera
i
The image from the Rear View Camera is
shown mirror-inverted on the COMAND display
(
page 33).Warning!
G
Please note that objects which do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck, may appear to be further
away than they actually are. In this case, you
should not use the guide lines to judge dis-
tance. The use of the guide lines to judge
distance increases the risk of impacting the
objects.
Warning!
G
The Rear View Camera is a supplement sys-
tem. It is not intended to, nor does it re-
place, the need for extreme care. The
responsibility during parking and other driv-
ing maneuvers always remains with the driv-
er.
The Rear View Camera may show obstacles
with a distorted perspective, incorrectly or
not at all.