display MERCEDES-BENZ CL-Class 2008 C216 Comand Manual

457 Controls in detail
Driving systems
Setting the following distance in
DISTRONIC Plus
You can set the specified following dis-
tance for DISTRONIC Plus by varying the
time setting between 1.0 and 2.0 seconds.
Using this time setting and the current
speed of your vehicle, DISTRONIC Plus cal-
culates and sets the required following dis-
tance to the preceding vehicle. The set
distance will be shown in the multifunction
display.The distance setting switch for the target
distance is located on the DISTRONIC Plus
lever.
1Distance setting switch for target dis-
tance
2To increase target distance
3To decrease target distance
!
Setting the automatic transmission to neu-
tral positionN while driving cancels the
DISTRONIC Plus. However, the automatic trans-
mission should not be set to neutral positionN
while driving except to coast when the vehicle is
in danger of skidding (e.g. on icy roads).
i
Depressing the accelerator pedal does not
deactivate DISTRONIC Plus. After brief accelera-
tion (e.g. for passing), DISTRONIC Plus will re-
sume to the last set speed.
Warning!
G
It is up to the driver to exercise discretion to
select the appropriate setting given road
conditions, traffic, driver’s preferred driving
style and applicable laws and driving recom-
mendations for safe following distance.

459 Controls in detail
Driving systems
“DISTRONIC PLUS
Currently Unavailable
See Oper. Manual”
appears in the multifunction display.
For cleaning and care of the
DISTRONIC Plus sensor, see “Cleaning the
DISTRONIC Plus*/ PRE-SAFE
® Brake* sys-
tem sensors (USA only)”(
page 599).
Another cause might be that the radar sen-
sors have been manually switched off in
the instrument cluster control system.
Please verify that the radar sensors are
switched on (
page 302).Turns and bends
In turns or bends, DISTRONIC Plus may not
detect a moving vehicle in front, or it may
detect one too soon. This may cause your
vehicle to brake late or unexpectedly.Offset driving
A vehicle traveling in your lane but offset
from your direct line of travel may not be
detected by DISTRONIC Plus. There will be
insufficient distance to the vehicle ahead.
i
If the message:
“DISTRONIC PLUS
Currently Unavailable
See Oper. Manual”
disappears during driving and the last speed
stored flashes for approximately 5 seconds, the
dirt (e.g. slush) has dissolved; DISTRONIC Plus is
available again.

471 Controls in detail
Driving systems
Collision warning
Park Assist can detect obstacles from a
considerable distance. If you drive in re-
verse towards an obstacle, you will hear a
warning tone. You must then brake in or-
der to avoid a collision. The warning tone
for a collision will not sound when the vehi-
cle is at a standstill very close to the obsta-
cle. In this case, you will hear a
corresponding tone for the warning indica-
tor in the rear area.
Switching Park Assist system on/off
The Park Assist system can be switched off
manually.
The Park Assist button with the indicator
lamp is located on the control panel on the
right-hand side of the instrument cluster.1Park Assist button
2Indicator lamp

Switching off Park Assist system:
Press button 1.
Indicator lamp 2 comes on.

Switching on Park Assist system:
Press button 1 again.
Indicator lamp 2 goes out.
Advanced Parking Guidance*
Advanced Parking Guidance is an electron-
ic parking aid equipped with radar sensors
that scan the area on both sides of vehicle.
When suitable parking space is found it is
shown in the display and you receive steer-
ing instructions for parking in that space.
i
During strong rainfall, the collision warning
may be triggered, for example, by water splash-
ing into the area of the sensors.
i
When the indicator lamp is illuminated, the
Park Assist system is switched off.
i
The Park Assist system is automatically
switched on when the ignition (
page 365) and
radar sensors are switched on (page 302).
Warning!
G
Advanced Parking Guidance is only an aid
and may display parking spaces that are not
suitable e.g. due to parking regulations, un-
suitable road/ground surfaces, driveways,
entrances/exits, etc.


472 Controls in detailDriving systemsAdvanced Parking Guidance only shows a
representation of the parking space in the
instrument cluster display as parking space
is first initially measured when driving past.
Subsequent changes to the parking space
are not taken into account, e.g. if the posi-
tion of the vehicle parked in front of or be-
hind the space changes or objects in the
parking space are moved. Moving objects
are not shown, e.g. pedestrians or vehicles
driving past. Advanced Parking Guidance
does not relieve you of the responsibility to
pay attention. If you only rely on Advanced
Parking Guidance, you may cause an acci-
dent and injure yourself and others.
You are always responsible for safety and
must continue to pay attention to your im-
mediate surroundings when parking and
maneuvering.
Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.!
Special attention must be paid to objects
with smooth surfaces or low silhouettes (e.g.
trailer couplings, painted posts, elevated cross-
bars or road curbs). Such objects may not be de-
tected by the system and can damage the
vehicle.
i
USA only:
This device has been approved by the FCC as a
“Vehicular Radar System”. The radar sensor is
intended for use in an automotive radar system
only. Removal, tampering, or altering of the de-
vice will void any warranties, and is not permitted
by the FCC. Do not tamper with, alter, or use in
any non-approved way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
i
Canada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation of the device.
Removal, tampering, or altering of the device will
void any warranties, and is not permitted. Do not
tamper with, alter, or use in any non-approved
way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
!
The operation and functionality of the Ad-
vanced Parking Guidance* can be affected or im-
paired by dirty sensors, especially at times of
snow and ice.
Make sure that the area on the bumpers around
the sensors is free of dirt, ice and/or slush, oth-
erwise Advanced Parking Guidance* may not
function properly, see “Cleaning the driving sys-
tems sensors” (
page 601).


473 Controls in detail
Driving systems
Use Advanced Parking Guidance for park-
ing spaces that are

parallel to the direction of travel


located on straight streets, i.e. not in
curves


on the same level as the street, i.e. not
on sidewalks, for example. Flat curbs
may possibly not be detected by Ad-
vanced Parking Guidance.
Parking instructions:


On narrow streets, drive by the parking
space as close as possible.


Parking spaces that are dirty, over-
grown or located in front of trailers may
not be detected correctly.


Also observe the Park Assist warning
indicator (
page 470) while Advanced
Parking Guidance is active.


How well your vehicle will be parked af-
ter completion of the Advanced Park-
ing Guidance depends on the position
and shape of the vehicles parked in
front of and behind the parking space
as well as the conditions of the imme-
diate surroundings. In certain cases,
Advanced Parking Guidance may guide
you too far into the parking space or
not far enough. If this is the case, can-
cel the parking procedure with Ad-
vanced Parking Guidance and correct
the vehicle position yourself.Detecting a parking space
Advanced Parking Guidance is active when
driving forward. The system operates at a
vehicle speed of up to 25 mph (40 km/h)
and automatically scans for and measures
potential parking spaces on both sides of
the vehicle. At a vehicle speed of below
10 mph (16 km/h), you see the white
parking space symbol as a system display
in the instrument cluster. As soon as Ad-
vanced Parking Guidance has detected a
suitable parking space, the parking space
symbol changes to blue.

474 Controls in detailDriving systemsDetected parking space1Detected parking spaces on the left
2Parking space symbol
3Detected parking spaces on the right
In order to be detected by Advanced Park-
ing Guidance, a parking space must be:

closed-in at the rear


parallel to the direction of travel


at least 5 ft (1.5 m) wide


at least 3.5 ft (1.0 m) longer than your
vehicleA parking space is shown in the display
when driving by until you have reached a
distance of 50 ft (15 m) from the space.
Advanced Parking Guidance only shows
parking spaces on the front-passenger
side of the vehicle unless you activate the
driver's side (left) turn signal. If you would
like to park on the driver's side, the left
turn signal must remain on until reverse
gear is engaged.Parking
The following describes how you can park
on the front-passenger side. Parking on
the driver's side is performed reversed left
to right.
If Advanced Parking Guidance detects an
obstacle behind the vehicle during the
parking procedure, you will hear an audible
warning. Stop the vehicle immediately. The
parking space and the lane blink in the in-
strument cluster. Only continue driv-
ing/parking after you have made sure that
this is possible to do in a safe manner. If
Advanced Parking Guidance no longer de-
tects any obstacles, the display in the in-
strument cluster stops blinking. You may
continue the parking procedure.

475 Controls in detail
Driving systems

Bring the vehicle to a standstill as long
as the desired parking space is dis-
played by the blue parking space sym-
bol in the instrument cluster.

Shift the automatic transmission to
positionR.
The message “Check Surroundings
Press 'OK' to Confirm” appears in the
multifunction display.

Press# on the multifunction steer-
ing wheel to confirm.
The display in the instrument cluster
changes to the Advanced Parking Guid-
ance.
1Green lane
2White bracket indicates the stopping
position

Where necessary, depending on the
distance to the parking space, back up
in a straight line a short distance.
This is indicated by a green lane1.

Back up until you hear an audible warn-
ing, then stop.
The stopping position has been
reached, indicated by a white
bracket2.
3Red lane indicates the current steering
wheel position
4Yellow lane indicates the required
steering wheel position

When the vehicle is stationary, turn the
steering wheel until the red lane3
matches up with the yellow lane4.
Warning!
G
Advanced Parking Guidance is only an aid
and may not detect all obstacles. At corners
or near smooth surfaces, Advanced Parking
Guidance may not detect an object correct-
ly. Advanced Parking Guidance does not re-
lieve you of the responsibility to pay
attention. You are always responsible for
safety and must continue to pay attention to
your immediate surroundings when parking
and maneuvering. Otherwise, you could en-
danger yourself and others.


477 Controls in detail
Driving systems
End positionDepending on the size of the parking
space, the vehicle may be positioned at an
angle in the parking space. Advanced Park-
ing Guidance guides you close to the rear
limit of the parking space where possible.
Adjust the end position by maneuver-
ing as needed.

Observe the Park Assist* display
(page 467).Canceling the Advanced Parking
Guidance

Press the Park Assist* button
(page 471).
The Advanced Parking Guidance is im-
mediately canceled and Park Assist* is
deactivated. No message is shown in
the multifunction display.
The Advanced Parking Guidance is auto-
matically canceled if guidance into the
parking space is no longer possible or if an
error occurs.
The parking space symbol disappears and
the message “Parking Guidance Canceled”
appears in the multifunction display.
Rear View Camera*
The Rear View Camera is an electronic and
visual parking aid. It shows you the area
behind the vehicle on the COMAND dis-
play.
In addition, the Rear View Camera contains
guide lines to help you with driving in re-
verse.
The area behind the vehicle is displayed as
a reverse-mirror image similar to the view
in a rear-view mirror.

478 Controls in detailDriving systemsThe Rear View Camera is in the handle
strip of the trunk lid.
1Rear View CameraView through the camera
i
The image from the Rear View Camera is
shown mirror-inverted on the COMAND display
(
page 33).Warning!
G
Please note that objects which do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck, may appear to be further
away than they actually are. In this case, you
should not use the guide lines to judge dis-
tance. The use of the guide lines to judge
distance increases the risk of impacting the
objects.
Warning!
G
The Rear View Camera is a supplement sys-
tem. It is not intended to, nor does it re-
place, the need for extreme care. The
responsibility during parking and other driv-
ing maneuvers always remains with the driv-
er.
The Rear View Camera may show obstacles
with a distorted perspective, incorrectly or
not at all.

479 Controls in detail
Driving systems
Special attention must be paid to objects
outside of the camera’s field of view such as
those located very close to or below the rear
bumper, or above the recessed grip of the
luggage compartment lid. Such objects may
not be detected by the system and can dam-
age the vehicle.
The Rear View Camera does not warn you
about impending collisions with objects. The
driver is always responsible for safety and
must continue to pay attention to the imme-
diate surroundings while parking or maneu-
vering the vehicle. This applies not only to
the area behind the vehicle, but also to the
area in front of and to the sides of the vehi-
cle. Failure to do so could result in injury to
persons and/or damage to the vehicle or
other property. We also recommend that the
driver uses the Parktronic system* or Park
Assist* when parking or maneuvering the
vehicle.
Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.Warning!
G
The Rear View Camera may not function if:

the trunk lid is not completely closed


it is raining or snowing heavily, or if
there is thick fog


in a very dark area


the camera is exposed to very strong
white light (white stripes may appear on
the COMAND display)


the surrounding area is lit with fluores-
cent light (the COMAND display can
flicker)


outside temperatures are very high (lens
condensation)


there is a sudden change in tempera-
ture, for example when you drive out of
the cold into a heated garage in winter
(lens condensation)


the camera lens is dirty or covered, see
“Cleaning the Rear View Camera* lens”
(page 602)


the rear of your vehicle is damaged. In
this case, have the position and setting
of the camera checked by a qualified
technician. Contact an authorized
Mercedes-Benz Center.
Do not use the Rear View Camera if the
roads are icy, slippery or covered with snow.
The vehicle could slip causing the actual ve-
hicle position to deviate from the one shown
on the COMAND display.
This may cause injury to you or others, or
damage the vehicle or objects.
Mounting tires/rims of other specification
than the original equipment tires/rims may
impair the function of the Rear View Cam-
era. Contact an authorized Mercedes-Benz
Center.