lane MERCEDES-BENZ CL-Class 2008 C216 Comand Manual

459 Controls in detail
Driving systems
“DISTRONIC PLUS
Currently Unavailable
See Oper. Manual”
appears in the multifunction display.
For cleaning and care of the
DISTRONIC Plus sensor, see “Cleaning the
DISTRONIC Plus*/ PRE-SAFE
® Brake* sys-
tem sensors (USA only)”(
page 599).
Another cause might be that the radar sen-
sors have been manually switched off in
the instrument cluster control system.
Please verify that the radar sensors are
switched on (
page 302).Turns and bends
In turns or bends, DISTRONIC Plus may not
detect a moving vehicle in front, or it may
detect one too soon. This may cause your
vehicle to brake late or unexpectedly.Offset driving
A vehicle traveling in your lane but offset
from your direct line of travel may not be
detected by DISTRONIC Plus. There will be
insufficient distance to the vehicle ahead.
i
If the message:
“DISTRONIC PLUS
Currently Unavailable
See Oper. Manual”
disappears during driving and the last speed
stored flashes for approximately 5 seconds, the
dirt (e.g. slush) has dissolved; DISTRONIC Plus is
available again.

460 Controls in detailDriving systemsLane changing
DISTRONIC Plus has not yet detected the
vehicle changing lanes. There will be insuf-
ficient distance to the lane-changing
vehicle.Narrow vehicles
Because of their narrow profile, the vehi-
cles traveling near the outer edge of the
lane have not yet been detected by
DISTRONIC Plus. There will be insufficient
distance to the vehicles ahead.Obstacles and stationary vehicles
DISTRONIC Plus does not brake for obsta-
cles or stationary vehicles. If, for example,
the vehicle detected in front of you chang-
es lanes to bypass an obstacle or station-
ary vehicle in front of it, DISTRONIC Plus
will not brake for the obstacle or stationary
vehicle.

474 Controls in detailDriving systemsDetected parking space1Detected parking spaces on the left
2Parking space symbol
3Detected parking spaces on the right
In order to be detected by Advanced Park-
ing Guidance, a parking space must be:

closed-in at the rear


parallel to the direction of travel


at least 5 ft (1.5 m) wide


at least 3.5 ft (1.0 m) longer than your
vehicleA parking space is shown in the display
when driving by until you have reached a
distance of 50 ft (15 m) from the space.
Advanced Parking Guidance only shows
parking spaces on the front-passenger
side of the vehicle unless you activate the
driver's side (left) turn signal. If you would
like to park on the driver's side, the left
turn signal must remain on until reverse
gear is engaged.Parking
The following describes how you can park
on the front-passenger side. Parking on
the driver's side is performed reversed left
to right.
If Advanced Parking Guidance detects an
obstacle behind the vehicle during the
parking procedure, you will hear an audible
warning. Stop the vehicle immediately. The
parking space and the lane blink in the in-
strument cluster. Only continue driv-
ing/parking after you have made sure that
this is possible to do in a safe manner. If
Advanced Parking Guidance no longer de-
tects any obstacles, the display in the in-
strument cluster stops blinking. You may
continue the parking procedure.

475 Controls in detail
Driving systems

Bring the vehicle to a standstill as long
as the desired parking space is dis-
played by the blue parking space sym-
bol in the instrument cluster.

Shift the automatic transmission to
positionR.
The message “Check Surroundings
Press 'OK' to Confirm” appears in the
multifunction display.

Press# on the multifunction steer-
ing wheel to confirm.
The display in the instrument cluster
changes to the Advanced Parking Guid-
ance.
1Green lane
2White bracket indicates the stopping
position

Where necessary, depending on the
distance to the parking space, back up
in a straight line a short distance.
This is indicated by a green lane1.

Back up until you hear an audible warn-
ing, then stop.
The stopping position has been
reached, indicated by a white
bracket2.
3Red lane indicates the current steering
wheel position
4Yellow lane indicates the required
steering wheel position

When the vehicle is stationary, turn the
steering wheel until the red lane3
matches up with the yellow lane4.
Warning!
G
Advanced Parking Guidance is only an aid
and may not detect all obstacles. At corners
or near smooth surfaces, Advanced Parking
Guidance may not detect an object correct-
ly. Advanced Parking Guidance does not re-
lieve you of the responsibility to pay
attention. You are always responsible for
safety and must continue to pay attention to
your immediate surroundings when parking
and maneuvering. Otherwise, you could en-
danger yourself and others.


476 Controls in detailDriving systems
The lane4 then turns green. If the
parking space is located within the dis-
play range, a white bracket with an ar-
row for the target position is shown at
the end of the green lane.
Driving into the parking space
1Green lane indicates the correct steer-
ing wheel position

Maintain the steering wheel position
and carefully back up.

Stop as soon as you hear the audible
warning.
The vehicle has reached the position
for countersteering.Countersteering
1Red lane indicates the current steering
wheel position
2Yellow lane indicates the required
steering wheel position

When the vehicle is stationary, turn the
steering wheel until the red lane1
matches up with the yellow lane2.
The lane2 then turns green and a
white arrow and a white bracket are
shown to indicate the target position.Reaching end position
1Green lane indicates the correct steer-
ing wheel position

Maintain the steering wheel position
and carefully back up until the end po-
sition has been reached.
The message appears “Parking Guid-
ance Finished” in the multifunction dis-
play and you will hear an audible
warning.
If the distance to the rear is too short,
you will also be audibly warned by the
Park Assist* system (
page 467).


485 Controls in detail
Driving systems
Blind Spot Assist*
Depending on production date, your vehi-
cle may not be equipped with this feature.
Blind Spot Assist uses radar sensors to
monitor the area on both sides of your ve-
hicle. It will assist you when you change
lanes driving at speeds of above 20 mph
(30 km/h). A warning will appear on the
outside rear view mirror as soon as anoth-
er vehicle is detected in the area being
monitored. If you then activate the corre-
sponding turn signals to change lanes, you
will see and hear a collision warning. Blind
Spot Assist operates using two sensors in
the front bumper and four sensors in the
rear bumper.In order for Blind Spot Assist to function,
the radar sensors must be switched on and
operational.
When travelling in Canada in a vehicle not
registered in Canada, you must switch off
the radar sensor system* (
page 302).
Canadian law does not permit the use of
the radar sensor system* (
page 302) for
vehicles from outside of Canada. When you
switch off the radar sensor system*, the
following functions are deactivated:


BAS Plus* (
page 68)


PRE-SAFE
® Brake* (
page 75)


DISTRONIC Plus* (
page 443)


Park Assist (
page 467)


Advanced Parking Guidance*
(page 471)


Blind Spot Assist* (
page 485)
Warning!
G
Blind Spot Assist is only a driving aid and
may not detect all vehicles. It is the driver’s
responsibility at all times to be attentive to
road, weather and traffic conditions and to
provide the steering, braking and other
driving inputs necessary to retain control of
the vehicle. Failure to do so could result in
recognizing dangers too late, possibly re-
sulting in an accident and serious injury to
yourself and others.
Warning!
G
Blind Spot Assist cannot detect road and
traffic conditions.
Blind Spot Assist may not be able to detect
narrow vehicles such as motorcycles or bi-
cycles, or it may not detect them until it is
too late.
The monitoring function may be impaired if
your sensors are dirty, subject to heavy
spray, or if visibility is poor due to e.g. snow,
rain, or fog. This can result in vehicles not
being detected or being detected too late.
It is the driver’s responsibility at all times to
be attentive to road, weather and traffic con-
ditions and to provide the steering, braking
and other driving inputs necessary to retain
control of the vehicle. Failure to do so could
result in recognizing dangers too late, possi-
bly resulting in an accident and serious inju-
ry to yourself and others.

486 Controls in detailDriving systemsSensor monitoring range
Blind Spot Assist is able to monitor a range
up to three meters to the rear and both
sides of the vehicle.
The Blind Spot Assist sensors are built into
t h e f r o n t a n d r e a r b u m p e r s . M a k e s u r e t h a t
the area of the bumpers around the sen-
sors is free of dirt, ice and snow. The radar
sensors must not be obstructed, for exam-
ple, by bicycle carriers or overhanging lug-
gage.
Warning!
G
Blind Spot Assist monitors certain areas in
the immediate vicinity of your vehicle. Vehi-
cles approaching and passing at increased
speeds will not be detected. There will be no
warning display and no audible warning.
When driving in a very wide lane, the sensors
may not be able to cover the entire width of
the neighboring lane. Vehicles driving on the
outside of the neighboring lane may not be
detected.
It is the driver’s responsibility at all times to
be attentive to road, weather and traffic con-
ditions and to provide the steering, braking
and other driving inputs necessary to retain
control of the vehicle. Failure to do so could
result in recognizing dangers too late, possi-
bly resulting in an accident and serious inju-
ry to yourself and others.
When driving in a very narrow lane, the sen-
sors may detect and display vehicles in the
second lane over. This will be the case if
there are vehicles driving on the inside edge
of their lane.!
In the event of a significant impact or dam-
age affecting the bumpers, have the radar sen-
sors checked by a qualified specialist workshop
such as a Mercedes-Benz Center. Failure to do
so can result in Blind Spot Assist not functioning
correctly.

487 Controls in detail
Driving systems
Indicator and warning lamps
1Yellow indicator lamp/red warning
lamp
Switching on: Make sure that the ra-
dar sensors (
page 302) and the Blind
Spot Assist (page 299) are switched
on.
With the ignition switched on, the warn-
ing lamp1 in the exterior mirror lights
up red.
With the engine running, the indicator
lamp1 in the exterior mirror lights up
yellow up to a speed of 20 mph
(30 km/h).Once a speed above 20 mph (30 km/h)
has been reached and


Blind Spot Assist detects no vehicle in
its range, the indicator lamp1 goes
out


Blind Spot Assist detects another vehi-
cle in its range, the warning lamp1 on
the corresponding side of the vehicle
turns red.Collision warning
If a vehicle is detected in the Blind Spot As-
sist range and you activate the turn signal,
a two-tone warning will sound and the red
warning lamp1 will flash.

Remain on the lane that you are cur-
rently on until traffic conditions permit
to change.
If the turn signal remains on, the red warn-
ing lamp1 will flash to indicate that vehi-
cles have been detected. No further
audible warnings will sound.
Warning!
G
Blind Spot Assist is not active at speeds be-
low approximately 20 mph (30 km/h). You
will not be alerted to the presence of vehi-
cles in the monitored area at these speeds.
It is the driver’s responsibility at all times to
be attentive to road, weather and traffic con-
ditions and to provide the steering, braking
and other driving inputs necessary to retain
control of the vehicle. Failure to do so could
result in recognizing dangers too late, possi-
bly resulting in an accident and serious inju-
ry to yourself and others.
Warning!
G
Do not change lanes or make turns, while
the red warning lamp
1
is flashing. Doing
so could result in an accident and seroius in-
jury to yourself and others.

692 Practical hintsReplacing bulbs1Installation device
2Bulb
Pull bulb2 out of the socket.

Insert new bulb2 into the socket.

Insert installation device1 into the
headlamp so that the handle of the in-
stallation device points up (left head-
lamp) or down (right headlamp).

Pull installation device1 down (left
headlamp) or up (right headlamp) until
it engages.

Attach cover (
page 691) and let it au-
dibly engage to close.
Corner-illuminating lamp
1Bulb holder
2Wire position

Turn bulb holder1 counterclockwise
until it disengages.

Take out bulb holder1.

Take bulb out of holder.

Insert new bulb into holder and press it
all the way down.

Insert bulb holder1 into guide in
headlamp.
The tab of the bulb holder must be po-
sitioned on the upper left-hand side
and wire2 must point downward and
to the left for the left headlamp, up-
ward and to the right for the right head-
lamp.

Turn bulb holder1 clockwise until it
engages.
i
Make sure to insert the bulb in the right di-
rection. The bulb must fit plane on the socket.