transmission MERCEDES-BENZ CL-Class 2008 C216 Comand Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2008, Model line: CL-Class, Model: MERCEDES-BENZ CL-Class 2008 C216Pages: 769, PDF Size: 10.18 MB
Page 397 of 769
396 Controls in detailLightingSwitching on corner-illuminating lamps
Switch on the left or right turn signal
(page 391), depending on whether
you are turning left or right.
or
Turn steering wheel in desired direc-
tion.
The corner-illuminating lamp on the
side of your steering direction comes
on.
Switching off the corner-illuminating
lamps
The combination switch for the turn signal
resets automatically after major steering
wheel movements. This will switch off the
corner-illuminating lamps if they were acti-
vated by switching on the left or right turn
signal.If the turn signal should stay on after mak-
ing the turn, the turn signal and corner-illu-
minating lamp can be switched off by
returning the combination switch to its
original position.
i
If you have switched on the turn signal for
one side but turn the steering wheel in the other
direction, the corner-illuminating lamp comes on
for the side indicated by the turn signal.
i
The corner-illuminating lamps temporarily
come on, on both sides of the vehicle if you turn
the steering wheel in one direction and then in
the other direction shortly thereafter.
i
The corner-illuminating lamps will come on
automatically depending on the steering angle,
even if you did not switch on either turn signal. If
the corner-illuminating lamps came on automat-
ically, they will also go out automatically depend-
ing on the steering angle.
i
When you shift the automatic transmission
in reverse gearR, the corner-illuminating lamp
opposite to your steering direction comes on.
The turn signal has no influence on the corner-il-
luminating lamp on the outside of the curve.
i
If you are driving faster than 43 mph
(70 km/h) when activating the turn signal indica-
tor, the corner-illuminating lamp function is
switched off.
i
The corner-illuminating lamp may remain lit
for a short time. The corner-illuminating lamp
comes on for no more than 20 seconds with the
vehicle standing still. It is then switched off even
if the turn signal is still switched on or you have
turned the steering wheel to full lock.
Page 402 of 769
401 Controls in detail
Windshield wipers
Intermittent wiping
Only switch on intermittent wiping under
wet weather conditions or in the presence
of precipitation.
Turn the combination switch to posi-
tion U or V.
The wipers move across the wind-
shield. Afterward, the wiping intervals
are determined by the wetness of the
windshield.
After the initial wipe, pauses between
wipes are automatically controlled by the
rain sensor.
Single wipe
Press the combination switch briefly in
the direction of arrow2 (
page 400)
to the resistance point.
The windshield wipers wipe one time
without washer fluid.
Wiping with windshield washer fluid
Press the combination switch in the di-
rection of arrow2 (
page 400) past
the resistance point.
The windshield wiper operates with
washer fluid.
For information on filling up the washer
reservoir, see “Windshield washer system
and headlamp cleaning system”
(
page 560).
i
When the windshield wipers are switched on
and you brake the vehicle to a stop, the wipers
operate more slowly.
!
Do not leave windshield wipers on an inter-
mittent setting when the vehicle is taken to an
automatic car wash or during windshield clean-
ing. Wipers will operate in the presence of water
sprayed on the windshield, and windshield wip-
ers may be damaged as a result.
!
If you have set intermittent wiping, dirt on
the surface of the rain sensor or optical effects
may cause the windshield wipers to wipe in an
undesired fashion. This could then damage the
windshield wiper blades or scratch the windows.
You should therefore switch off the windshield
wipers when weather conditions are dry.
i
Intermittent wiping is interrupted when the
vehicle is at a standstill and a door is opened.
This protects persons getting into or out of the
vehicle from being sprayed.
Intermittent wiping will be continued when
both doors are closed and the automatic
transmission is set to positionD orR
or
the wiper setting is changed using the com-
bination switch
i
To prevent smears on the windshield or
noisy/chattering wiper blades, wipe with wind-
shield washer fluid every now and then even
when it is raining.
Page 407 of 769
406 Controls in detailDriving and parking
Starting the engine Automatic transmission
Gearshift pattern for automatic
transmissionPPark position
RReverse gear
NNeutral
DDrive position
For more information on how to operate
the gear selector lever, see “Automatic
transmission” (
page 417).
Warning!
G
Make sure that absolutely no objects are ob-
structing the pedals’ range of movement.
Keep the driver’s footwell clear of all obsta-
cles. If there are any floormats or carpets in
the footwell, make sure that the pedals still
have sufficient clearance.
During sudden driving or braking maneuvers
the objects could get caught between the
pedals. You could then no longer brake or
accelerate. This could lead to accidents and
injury.
Warning!
G
Inhalation of exhaust gas is hazardous to
your health. All exhaust gas contains carbon
monoxide (CO), and inhaling it can cause un-
consciousness and possible death.
Do not run the engine in confined areas
(such as a garage) which are not properly
ventilated. If you think that exhaust gas
fumes are entering the vehicle while driving,
have the cause determined and corrected
immediately. If you must drive under these
conditions, drive with at least one window
fully open.
Page 408 of 769
407 Controls in detail
Driving and parking
Starting with the SmartKey
Make sure the automatic transmission
is set to park positionP.
The gear position indicator in the multi-
function display should be on park
positionP.
Do not depress accelerator.
Turn the SmartKey in the starter switch
to position3 and hold until the engine
starts (
page 365).
For information on turning off the engine
with the SmartKey, see “Turning off the en-
gine” (
page 415).Starting with KEYLESS-GO*
You can start your vehicle without the
SmartKey in the starter switch using the
KEYLESS-GO start/stop button on the
starter switch.
The SmartKey with KEYLESS-GO must be
located in the vehicle.
KEYLESS-GO start/stop button1USA only
2Canada only
Make sure KEYLESS-GO start/stop
button is inserted in the starter switch
(page 366).
Make sure the automatic transmission
is set to park positionP.
The gear position indicator in the multi-
function display should be on park
positionP.
Depress the brake pedal during the
starting procedure.
i
You can also use the “touch-start” function.
Turn the SmartKey to position 3 and release it
again immediately. The engine then starts auto-
matically.
i
You can also start the engine with the auto-
matic transmission set to neutral positionN.
Warning!
G
As long as the SmartKey with KEYLESS-GO
is in your vehicle, the vehicle can be started.
Therefore, never leave children unattended
in the vehicle, as they could otherwise acci-
dentally start the engine.
When leaving the vehicle, always take the
SmartKey with KEYLESS-GO with you and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.
Page 409 of 769
408 Controls in detailDriving and parking
Do not depress accelerator.
Press KEYLESS-GO start/stop button
once.
The engine starts if the SmartKey with
KEYLESS-GO is in the vehicle.
For information on turning off the engine
with KEYLESS-GO, see “Turning off the en-
gine” (
page 415).Starting difficulties
The engine does not start. You can hear
the starter.
There could be a malfunction
in the engine electronics, or
in the fuel supply system
Carry out the following steps:
If you are starting the engine with the
SmartKey: Turn SmartKey in starter
switch to position0 and repeat starting
procedure.
If you are starting the engine with
KEYLESS-GO*: Close any doors that
may be open to allow for better detec-
tion of the SmartKey with
KEYLESS-GO*.
or
Remove the KEYLESS-GO* start/stop
button from starter switch.
Start the engine with the SmartKey as
radio signals from another source may
be interfering with the SmartKey with
KEYLESS-GO*.
Repeat the starting procedure
(page 406).
If the engine does not start after several
starting attempts:
Call Roadside Assistance.
Contact an authorized Mercedes-Benz
Center or call Roadside Assistance.
i
You can also start the engine with the auto-
matic transmission set to neutral positionN.
i
If you wish to start the vehicle with the
SmartKey instead of the KEYLESS-GO feature,
remove the KEYLESS-GO start/stop button from
the starter switch and proceed as described in
“Starting with the SmartKey” (
page 407).
!
Remember that extended starting attempts
can drain the battery.
Page 410 of 769
409 Controls in detail
Driving and parking
The engine does not start. You cannot
hear the starter.
The battery may not be sufficiently
charged.
Have the vehicle jump-started
(page 707).
If the engine will not start despite a jump
start:
Call Roadside Assistance.
Contact an authorized Mercedes-Benz
Center or call Roadside Assistance.
Driving off
Depress the brake pedal.
The gear selector lever can now be
used.
Shift the automatic transmission to
drive positionD or reverse gearR.
Release the brake pedal.
Carefully depress the accelerator
pedal.
The electronic parking brake is auto-
matically released (
page 412).
The red brake warning lamp 0
(USA only) or ! (Canada only) in the
instrument cluster goes out.After a cold start, the automatic transmis-
sion shifts at a higher engine revolution.
This allows the catalytic converter to reach
its operating temperature earlier.
i
Wait for the gear selection process to com-
plete before setting the vehicle in motion.
i
Shifting from park position P to reverse
gearR, neutral positionN, or drive positionD is
only possible with the brake pedal depressed.
Without the brake pedal depressed, the gear se-
lector lever can be moved, but the parking pawl
remains engaged, not allowing shifting to occur.
!
If you hear a warning signal, the red indica-
tor lamp 0 (USA only) or ! (Canada only)
in the instrument cluster flashes and the mes-
sage “Please Release Parking Brake” appears in
the multifunction display when driving off, you
are driving with the electronic parking brake en-
gaged, or you are carrying out an emergency
brake application with the electronic parking
brake.
Release the electronic parking brake
(
page 412).
i
Once the vehicle is in motion, the automatic
central locking system engages and the locking
knobs in the doors move down.
The automatic door lock feature can be deacti-
vated (page 263).
You can open a locked door from the inside.
Open door only when conditions are safe to do
so.
Page 411 of 769
410 Controls in detailDriving and parking
For more information, see “Driving instruc-
tions” (
page 539).
Turn signalsCombination switch1Turn signals, right
2Turn signals, left
Press the combination switch in the
direction of arrow1 or2.
The corresponding turn signal indicator
lampL orK in the instrument
cluster flashes (
page 30).
The combination switch resets automati-
cally after major steering wheel move-
ments.
Warning!
G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of loss of control.Warning!
G
It is dangerous to shift the gear selector le-
ver out of position P or N if the engine speed
is higher than idle speed. If your foot is not
firmly on the brake pedal, the vehicle could
accelerate quickly forward or in reverse. You
could lose control of the vehicle and hit
someone or something. Only shift into gear
when the engine is idling normally and when
your right foot is firmly on the brake pedal.
!
Shift the automatic transmission to
positionP or R only when the vehicle is stopped
in order to avoid damaging the transmission.
!
Do not run cold engine at high engine
speeds. Running a cold engine at high engine
speeds may shorten the service life of the en-
gine. This is not covered by the Mercedes-Benz
Limited Warranty
CL 63 AMG and CL 65 AMG only:
At engine temperatures below 68°F (20° C), the
maximum speed is restricted in order to protect
the engine. Avoid driving the vehicle at full speed
while the engine is cold in order to prevent pre-
mature engine wear as well as diminished com-
fort.
!
Simultaneously depressing the accelerator
pedal and applying the brakes reduces engine
performance and causes premature brake wear
and drivetrain wear which is not covered by the
Mercedes-Benz Limited Warranty.
Page 413 of 769
412 Controls in detailDriving and parkingParking
Electronic parking brakeWarning!
G
With the engine not running, there is no
power assistance for the brake and the
steering systems. In this case, it is impor-
tant to keep in mind that a considerably
higher degree of effort is necessary to brake
and steer the vehicle.
Warning!
G
Do not park this vehicle in areas where com-
bustible materials such as grass, hay, or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
To reduce the risk of personal injury as a re-
sult of vehicle movement, before turning off
the engine and leaving the vehicle always:
Keep right foot on brake pedal.
Engage electronic parking brake.
Shift the automatic transmission to park
position P.
Slowly release brake pedal.
When parked on an incline, turn front
wheels towards the road curb.
Turn the SmartKey to starter switch
position0 and remove, or press
KEYLESS-GO* start/stop button
(page 366).
Take the SmartKey or the SmartKey with
KEYLESS-GO* with you and lock vehicle
when leaving.
Warning!
G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. Children could release the
electronic parking brake and/or shift the
automatic transmission out of park
positionP, either of which could result in an
accident and/or serious personal injury.
Page 414 of 769
413 Controls in detail
Driving and parking
1Handle for electronic parking brake
Manually releasing electronic parking
brake
Pull handle1.
The red indicator lamp 0 (USA only)
or ! (Canada only) in the instru-
ment cluster goes out.
You cannot release the electronic parking
brake until the ignition is switched on.Automatically releasing electronic
parking brake
Your vehicle’s electronic parking brake is
automatically released when:
The engine is running.
Transmission is in drive position D or
reverse gearR.
The hood is closed.
You have fastened your seat belt.
You step on the accelerator pedal.
If reverse gear R is engaged, the trunk
must be closed.
Warning!
G
Getting out of your vehicle with the automat-
ic transmission not fully engaged in park
positionPis dangerous. Also, when parked
on an incline, park positionP alone may not
prevent your vehicle from moving, possibly
hitting people or objects.
Always engage the electronic parking brake
in addition to shifting to park positionP
(page 406).
When parked on an incline, turn front wheels
towards the road curb.
i
If you have not fastened your seat belt, the
following conditions must be met in order for the
electronic parking brake to be automatically re-
leased:
The driver’s door is closed.
You must move the gear selector out of park
positionP or drive faster than 2 mph
(3 km/h).
Page 416 of 769
415 Controls in detail
Driving and parking
Turning off the engine
Shift the automatic transmission to
park positionP (
page 421).
Turning off with SmartKey
Turn the SmartKey in the starter switch
to position0 (
page 365) and remove
it.
The immobilizer is activated.Turning off with KEYLESS-GO*
Press the KEYLESS-GO start/stop
button (
page 366) to turn off the en-
gine.
With the driver’s door closed, the start-
er switch is now in position1. With the
driver’s door opened, the starter switch
is set to position0, same as SmartKey
removed from starter switch
(
page 365).
i
If the engine cannot be turned off as de-
scribed, see “Emergency engine shut-down”
(
page 717).Warning!
G
Do not turn off the engine before the vehicle
has come to a complete stop. With the en-
gine not running, there is no power assis-
tance for the brake and steering systems. In
this case, it is important to keep in mind that
a considerably higher degree of effort is nec-
essary to brake and steer the vehicle.
!
Observe instructions
when taking the vehicle through an
automatic conveyor type car wash
(page 598)
when towing the vehicle (
page 710)
!
If you turn off the engine using the
SmartKey and
remove the SmartKey from the starter
switch
or
open a door
the transmission will shift to park positionP
automatically.
Keep in mind that turning off the engine with the
SmartKey alone only will automatically shift the
transmission to neutral positionN.
i
In an emergency you can turn off the engine
while driving by pressing and holding the
KEYLESS-GO start/ stop button for
approximately 3 seconds.
!
If you turn off the engine using the
KEYLESS-GO start/stop button and open the
driver’s or passenger door, the transmission will
shift to park positionP automatically.
Keep in mind that turning off the engine using
the KEYLESS-GO start/stop button alone only
will automatically shift the transmission to
neutral positionN.