brake sensor MERCEDES-BENZ CL-Class 2008 C216 Comand Manual

573 Operation
Tires and wheels

Switch on the ignition (
page 365).

Press( or& to select the menu
“Service”.

Press$ or% to select “Tire
Pressure”.

Press#.
i
When the message “Tire Pressures Dis-
played After Driving a Few Minutes” appears in
the display, the individual inflation pressure val-
ues are matched with the tires. The individual
values are displayed after a few minutes driving.Warning!
G
It is the driver’s responsibility to calibrate
the Advanced TPMS on the recommended
cold inflation pressure. Underinflated tires
affect the ability to steer or brake the vehi-
cle. You might lose control over the vehicle.
i
With a spare wheel without wheel sensor
mounted, the system may still indicate the tire
inflation pressure of the removed wheel for some
minutes. If this happens, keep in mind that the
indicated value where the spare wheel is mount-
ed does not reflect the actual spare tire inflation
pressure.
Warning!
G
The Advanced TPMS does not indicate a
warning for wrongly selected inflation pres-
sures. Always adjust tire inflation pressure
according to the Tire and Loading Informa-
tion placard on the driver’s door B-pillar or,
if available, the supplemental tire inflation
pressure information on the inside of the
fuel filler flap.
The Advanced TPMS is not able to issue a
warning due to a sudden dramatic loss of
pressure (e.g. tire blowout caused by a for-
eign object). In this case bring the vehicle to
a halt by carefully applying the brakes and
avoiding abrupt steering maneuvers.

575 Operation
Tires and wheels
Reactivating Advanced TPMS
The Advanced TPMS must be reactivated
when you have adjusted the tire inflation
pressure to a new level (e.g. because of dif-
ferent load or driving conditions). The Ad-
vanced TPMS is then recalibrated to the
current tire inflation pressures.
Using the Tire and Loading Information
placard on the driver’s door B-pillar
(page 564) or, if available, the sup-
plemental tire inflation pressure
information on the inside of the fuel fill-
er flap (
page 550), make sure the tire
inflation pressure of all four tires is
correct.

Switch on the ignition (
page 365).

Press( or& to select the menu
“Service”.

Press$ or% to select
“Tire Pressure”.

Press#.
You will see

the current inflation pressures for
each tire
or


the message
“Tire Pressures
Displayed After Driving
a Few Minutes”
appear in the multifunction display.

Press%.
The message
“Use Current
Pressures As New
Reference Values
Press "OK" to Confirm
Tire Press.”
appears in the multifunction display.
Warning!
G
It is the driver’s responsibility to calibrate
the Advanced TPMS on the recommended
cold inflation pressure. Underinflated tires
affect the ability to steer or brake the vehi-
cle. You might lose control over the vehicle.
i
Reactivate the Advanced TPMS after adjust-
ing the tire inflation pressure to the inflation
pressure recommended for the vehicle operating
condition. Tire inflation pressure should only be
adjusted on cold tires. Observe the recommend-
ed tire inflation pressure on the Tire and Loading
Information placard on the driver’s door B-pillar
(
page 564). Some vehicles may have supple-
mental tire inflation pressure information for
driving at high speeds (
page 570) or for vehi-
cle loads less than the maximum loaded vehicle
condition. If such information is provided, it can
be found on the inside of the fuel filler flap
(
page 550).
i
After wheel rotation or sensor replacement,
the vehicle must be parked for 20 minutes be-
fore attempting to reactivate the Advanced
TPMS.
i
The menu overview can be found on
(
page 284).


598 OperationVehicle careAutomatic car wash
You can have your car washed in an auto-
matic car wash from the start.
To protect the filter system, switch the
automatic climate control to air recir-
culation mode (
page 496).
If the vehicle is very dirty, prewash it be-
fore running it through the automatic car
wash.When taking the vehicle through an auto-
matic conveyor type car wash, observe the
following instructions.
Vehicles with SmartKey:

With the vehicle at a standstill and the
ignition switched on shift the
automatic transmission to neutral
positionN.

If engaged, manually release the
electronic parking brake (
page 413).

Switch off the ignition and leave the
SmartKey in the starter switch.Vehicles with KEYLESS-GO*:

With the vehicle at a standstill, depress
the brake pedal and keep it pressed.

With the ignition switched on shift the
automatic transmission to park
positionP.

Release the brake pedal.

Remove the KEYLESS-GO start/stop
button from the starter switch
(page 366).

Insert the SmartKey with KEYLESS-GO
into the starter switch.

Switch on the ignition.

Depress the brake pedal.

Shift the automatic transmission to
neutral positionN.

Release the brake pedal.

If engaged, manually release the
electronic parking brake (
page 413).

Switch off the ignition and leave the
SmartKey with KEYLESS-GO in the
starter switch.
!
Do not clean your vehicle in an automatic
touchless car wash which uses caustic spray.
Otherwise the caustic spray will damage the
paint or ornamental moldings.
!
Make sure that the windshield wiper switch
is set to0 (
page 400). Otherwise, e.g. the rain
sensor could activate and cause the wipers to
move unintentionally. This may lead to vehicle
damage.
Due to the width of the vehicle, fold in exterior
rear view mirrors prior to running the vehicle
through an automatic car wash to prevent dam-
age to the mirrors.
Warning!
G
When leaving the SmartKey or SmartKey
with KEYLESS-GO* in the starter switch, do
not leave children unattended in the vehicle.
It is possible for children to switch on the
ignition which could result in unsupervised
use of vehicle equipment. Unsupervised use
of vehicle equipment could result in an
accident and/or serious personal injury.

599 Operation
Vehicle care
Ornamental moldings
For regular cleaning and care of ornamen-
tal moldings, use a damp cloth.Headlamps, tail lamps, side markers,
turn signal lenses

Use a mild car wash detergent, such as
Mercedes-Benz approved Car
Shampoo, with plenty of water.Cleaning the DISTRONIC Plus*/
PRE-SAFE
® Brake* system sensors
The sensors are integrated in the front
bumpers and cannot be seen from the
outside.
1Sensor cover
2Bumper area near sensors

Switch off the ignition (
page 365).

Use a mild car wash detergent, such as
Mercedes-Benz approved Car
Shampoo, with plenty of water and a
non-scratching cloth to clean sensor
cover1.
i
After running the vehicle through an auto-
matic car wash, wipe any wax off of the wind-
shield (
page 603). This will prevent smears
and reduce wiping noise which can be caused by
residual wax on the windshield.
When leaving the car wash, make sure that the
mirrors are folded out. Otherwise they may
vibrate.
!
Do not use chrome cleaner on ornamental
moldings. Although ornamental moldings may
have chrome appearance, they could be made of
anodized aluminum that will be damaged when
cleaned with chrome cleaner. Instead, use a
damp cloth to clean those ornamental moldings.
For very dirty ornamental moldings of which you
are sure are chrome-plated, use a chrome clean-
er. If in doubt whether an ornamental molding is
chrome-plated, contact an authorized
Mercedes-Benz Center.
!
Only use window cleaning solutions that are
suitable for plastic lamp lenses. Window clean-
ing solutions which are not suitable may damage
the plastic lamp lenses of the headlamps. There-
fore, do not use abrasives, solvents or cleaners
that contain solvents.
Never apply strong force and only use a soft,
non-scratching cloth when cleaning the lenses.
Do not attempt to wipe dirty lenses with a dry
cloth or sponge.
Otherwise you may scratch or damage the lens
surface.


601 Operation
Vehicle care
Cleaning the driving systems sensors
The sensors are integrated in the front and
rear bumpers and cannot be seen from the
outside. They work with the following sys-
tems:

BAS Plus*


PRE-SAFE
® Brake*


Blind Spot Assist*


Park Assist*


Advanced Parking Guidance*
1Bumper area near sensors

Switch off the ignition (
page 365).

Use a mild car wash detergent, such as
Mercedes-Benz approved Car Sham-
poo, with plenty of water and a soft,
non-scratching cloth to clean the
bumper area near sensors.
!
To prevent scratches or damage to the sur-
face, never apply strong force and only use a
soft, non-scratching cloth when cleaning the
bumper area near sensors. Do not attempt to
wipe a dirty bumper with a dry cloth or sponge.

632 Practical hintsWhat to do if …?Display
Possible cause/consequence
Possible solution
Next Service X
Due in ... days
Due in ... mls (km)
Service X must be carried out in ... days or
after ... miles (kilometers) (
page 592).

Have the maintenance service carried out by an authorized
Mercedes-Benz Center.
Only Shift to
Position 'P' When
Vehicle Is Stationary
You have tried to Shift the automatic trans-
mission to park positionP using the gear
selector lever although the vehicle is still in
motion.

Stop your vehicle as soon as it is safe to do so.

Shift the automatic transmission to park positionP.

Engage the electronic parking brake (
page 412).
Park Assist
Currently Unavailable
See Oper. Manual
Park Assist* is deactivated because the
area around the sensors* in the front or
the rear bumper (
page 601) is dirty.

Clean the front and rear bumper (
page 601).
Park Assist* is deactivated because the
battery voltage is insufficient.

Have the battery checked by an authorized Mercedes-Benz
Center.
Park Assist* is switched off because the
radar sensor system* is temporarily inop-
erative due to electromagnetic interfer-
ence near television and radio transmitter
stations, toll stations, speed measuring
systems, etc.

Wait until the message in the multifunction display disappears.
Park Assist
Inoperative
Park Assist* is unavailable due to a mal-
function.

Contact an authorized Mercedes-Benz Center as soon as
possible.

635 Practical hints
What to do if …?
Display
Possible cause/consequence
Possible solution
Parking Guidance
Finished
Advanced Parking Guidance* The vehicle is
in the end position.
The display message disappears automatically.
PRE-SAFE
Inoperative
See Oper. Manual
PRE-SAFE
® itself has failed. All other occu-
pant safety systems, such as the air bags,
are still available.

Contact an authorized Mercedes-Benz Center as soon as
possible.
Radar Sensors
Deactivated
See Oper. Manual
You attempt to activate DISTRONIC Plus*,
Park Assist* or PRE-SAFE
® Brake* even
though you have switched off the radar sen-
sors* on the vehicle.

Check if the radar sensors* may be switched on (
page 302).

Switch on the radar sensors* using the instrument cluster
control system.
Service X
Due
Your vehicle is due for maintenance service
(page 592).

Have the maintenance service carried out by an authorized
Mercedes-Benz Center.
Service X Exceeded
by X days
by XXX mls (km)
Service X must be carried within the next ...
or before you have driven ... miles (kilome-
ters).

Have the maintenance service carried out by an authorized
Mercedes-Benz Center as soon as possible.
!
Failure to have the vehicle maintained in ac-
cordance with the Maintenance Booklet and
maintenance service indicator at the designated
times/mileage will result in vehicle damage not
covered by the Mercedes-Benz Limited
Warranty. For more information, see “Mainte-
nance” (
page 592).

637 Practical hints
What to do if …?
Display
Possible cause/consequence
Possible solution
Tire Pressure Monitor
Currently Unavailable
The Advanced TPMS is unable to monitor
the tire inflation pressure due to:

a nearby radio interference source


the on-board voltage is too low


excessive wheel sensor temperatures
As soon as the causes for the malfunction are no longer present,
the Advanced TPMS automatically becomes active again after a
few minutes driving.
Warning!
G
Do not drive with a flat tire. A flat tire affects
the ability to steer or brake the vehicle. You
may lose control of the vehicle. Continued
driving with a flat tire will cause excessive
heat build-up and possibly a fire.
Follow recommended tire inflation pres-
sures.
Do not underinflate tires. Underinflated tires
wear excessively and/or unevenly, adverse-
ly affect handling and fuel economy, and are
more likely to fail from being overheated. Do
not overinflate tires. Overinflated tires can
adversely affect handling and ride comfort,
wear unevenly, increase stopping distance,
and result in sudden deflation (blowout) be-
cause they are more likely to become punc-
tured or damaged by road debris, potholes
etc.

645 Practical hints
What to do if …?
Display
Possible cause/consequence
Possible solution
Service
See Oper. Manual
CL 600 and CL 65 AMG only:
The brake system sensors are malfunction-
ing. The brake system continues to function
normally with full brake force boost.

Continue driving with added caution.

Have the system checked at an authorized
Mercedes-Benz Center as soon as possible.
(USA only)(Canada only)
Check
Brake Pad Wear
The brake pads have reached their wear
limit.

Have the brake pads replaced as soon as
possible.
!
Brake pad thickness must be visually
checked by a qualified technician at the intervals
specified in the Maintenance Booklet.

664 Practical hintsWhat to do if …?Display
Possible cause/consequence
Possible solution
Check
Center Brake Lamp
The high mounted brake lamp is malfunc-
tioning. This message will only appear if all
light emitting diodes have stopped working.

Contact an authorized Mercedes-Benz
Center as soon as possible.
Check Left
Cornering Light
The left-hand corner-illuminating lamp is
malfunctioning.

Replace the bulb as soon as possible
(page 688).
Check Right
Cornering Light
The right-hand corner-illuminating lamp is
malfunctioning.

Replace the bulb as soon as possible
(page 688).
Check
Left Low Beam
The left low beam lamp is malfunctioning.

Contact an authorized Mercedes-Benz
Center as soon as possible.
Check
Right Low Beam
The right low beam lamp is malfunctioning.

Contact an authorized Mercedes-Benz
Center as soon as possible.
Active Headlamps
Inoperative
The active headlamps are malfunctioning.

Contact an authorized Mercedes-Benz
Center as soon as possible.
Auto Lamp Function
Inoperative
The light sensor is malfunctioning. Daytime
driving lamps are switched on.

Contact an authorized Mercedes-Benz
Center as soon as possible.
To switch off the headlamps (U.S. vehicles only):

Switch off daytime running lamps in the in-
strument cluster control system
(page 301).

Turn the exterior lamp switch to position0
(page 391).