warning MERCEDES-BENZ CL500 2007 C216 Owner's Manual

446 Controls in detail
Driving systems
Night View Assist*
Night View Assist illuminates the road with
infrared light in addition to the normal
headlamps.
A camera at the top of the windshield mea-
sures the infrared light and shows a
black-and-white image on the multifunc-
tion display. The image on the multifunction display cor-
responds to a road lit up by high-beam
headlamps.
The Night View Assist image on the multi-
function display is not impaired

by the headlamps of approaching vehi-
cles

if you cannot switch on the high beams
due to oncoming traffic
As a result, you can better follow the
course of the road and detect obstacles
earlier on.The camera is at the top of the windshield.
1Night View Assist camera
Warning!G
Night View Assist is only an aid to support
you while driving and cannot substitute your
careful attention. Do not rely on the display
of the Night View Assist; instead, continue
to look through the windshield. You are al-
ways responsible for safety and must drive
in accordance with traffic conditions. Other-
wise, you could endanger yourself and oth-
ers.
If it is foggy, raining or snowing, the clarity of
the Night View Assist image on the multi-
function display may be diminished.Warning!G
Night View Assist cannot record objects im-
mediately in front of or next to the vehicle.
When maneuvering, continue to look
through the windshield. Make sure no per-
sons or animals are in the area in which you
are maneuvering. You could otherwise in-
jure them.
iInfrared light is invisible to the human eye
and can therefore remain permanently switched
on without blinding oncoming traffic.

448 Controls in detail
Driving systems
Adjusting instrument cluster illumina-
tion
1Knob
Make sure the Night View Assist is
switched on.
Brightening illumination: Turn
knob1 clockwise.
Dimming illumination: Turn knob1
counterclockwise.Dirty or fogged-up windshield
If the windshield in front of the camera is
fogged up on the inside or outside or if it is
dirty, the Night View Assist image is
diminished.Removing condensation
Check settings of automatic climate
control and change them, if necessary
(
page 453).
Swing the camera cover downward
(
page 561).
Cleaning inside of windshield
Clean inside of windshield in front of
camera with a soft, non-scratching
cloth (
page 561).
Warning!G
Please do not forget that your primary re-
sponsibility is to drive the vehicle. A driver’s
attention to the road must always be
his/her primary focus when driving. For
your safety and the safety of others, stop be-
fore trying to remove window fogging or
cleaning the window in front of the
Night View Assist camera.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet
(approximately 14 m) every second.

451 Controls in detail
Air vents
Please comply with the following instruc-
tions in order for the automatic climate
control to function optimally:

Keep the air intake grille in front of the
windshield free of snow, leaves, sticks,
and any other debris.

Always keep all air vents and grilles in
the passenger compartment free from
obstruction.
Item
1Left side defroster vent, fixed
2Left side air vent, adjustable
3Left center air vent, adjustable
4Thumbwheel for air volume control
for left center air vent
5Thumbwheel for air volume control
for right center air vent
6Right center air vent, adjustable
7Right side air vent, adjustable
8Right side defroster vent, fixed
9Automatic climate control panel
aLeft rear center air vent, adjustable
bRight rear center air vent, adjustable
cThumbwheel for right rear center air
vents
dThumbwheel for left rear center air
vents
Warning!G
When operating the automatic climate con-
trol, the air that enters the passenger com-
partment through the air vents can be very
hot or very cold (depending on the set tem-
perature). This may cause burns or frostbite
to unprotected skin in the immediate area of
the air vents.
Always keep sufficient distance between un-
protected parts of the body and the air
vents. If necessary, use the air distribution
adjustment (
page 246) to direct the air to
air vents in the vehicle interior that are not
in the immediate area of unprotected skin.

454 Controls in detail
Automatic climate control
The automatic climate control is operation-
al whenever the engine is running. You can
operate the climate control system in ei-
ther the automatic or manual mode. The
system cools or heats the interior depend-
ing on the selected interior temperature
and the current outside temperature.
It can only function optimally when you are
driving with the windows and the tilt/slid-
ing sunroof closed.
It is possible to completely deactivate the
climate control system (
page 455). Nearly all dust particles, pollutants and
odors are filtered out before outside air en-
ters the passenger compartment through
the air distribution system.The following automatic climate control
functions can be operated via COMAND:
iIf you have the air distribution and air vol-
ume automatically controlled, you can adjust the
temperature, footwell temperature and air flow.
The following basic settings are recommended:

Automatic air distribution control
(
page 453)

Temperature: 72°F (22°C) (page 456)

Footwell temperature: 0 (page 249)

Air flow: focused (page 249)
Warning!G
Follow the recommended settings for heat-
ing and cooling given on the following pages
and in the “COMAND automatic climate
control” section (
page 244). Otherwise
the windows could fog up, impairing visibili-
ty and endangering you and others.
iSevere conditions (e.g. strong air pollution)
may require replacement of the filter before its
scheduled interval. A clogged filter will reduce
the air volume to the interior.
If the vehicle interior is hot, ventilate the interior
before driving off, see “Summer opening fea-
ture” (
page 376). The automatic climate con-
trol will then adjust the interior temperature to
the set value much faster.
Keep the air intake grille in front of the wind-
shield free of snow, leaves, sticks, and any other
debris.
Do not obstruct air volume by placing objects on
the air volume-through exhaust slots below the
rear window.
FunctionPage
Temperature245
Air distribution246
Air volume246
Switching off cooling (“ACOFF”)247
Central climate control (“Mono”)248
Footwell temperature249
Air flow from air vents249

455 Controls in detail
Automatic climate control
Deactivating climate control system
Deactivating: Press button´
(
page 453) up or down.
The indicator lamp on the button
comes on. You will see “Climate Con-
trol OFF” in the COMAND display.
Reactivating: Press button´
(
page 453) up or down.
The indicator lamp on the button goes
out. You will see the previous settings
in the COMAND display.Operating climate control system in
automatic mode
Air distribution and air volume is adjusted
automatically by the automatic climate
control system. You can also adjust the
settings for air distribution and air volume
manually.
Activating
Press buttonU (page 453) up or
down.
The indicator lamp on the button
comes on.Deactivating
Press buttonU (page 453) up or
down.
or
Adjust air distribution (page 246).
or
Adjust air volume (page 456).
The indicator lamp on buttonU
goes out. The automatic function is
switched off.
You can adjust the air distribution
(
page 246) or air volume
(
page 456) manually.
Warning!G
When the automatic climate control is
switched off, the outside air supply and cir-
culation are also switched off. Only choose
this setting for a short time. Otherwise the
windows could fog up, impairing visibility
and endangering you and others.
iIn automatic mode, cooling with dehumidify
is switched on. This function can be switched off
if necessary (
page 247).

458 Controls in detail
Automatic climate control
Maximum cooling MAXCOOL (USA only)
If U is selected on both the left and
right side and there is a high demand for
cooling, the display “MAXCOOL” appears
in the COMAND display.
This provides the fastest possible cooling
of the vehicle interior (when windows and
tilt/sliding sunroof are closed).
Air recirculation mode
Switch to air recirculation mode to prevent
unpleasant odors from entering the vehicle
from the outside (e.g. before driving in a
tunnel). This setting cuts off the intake of
outside air and recirculates the air in the
passenger compartment.
Activating: Press button,
(
page 453) up or down.
The indicator lamp on the button
comes on.Warning!G
Any accumulation of snow and ice should be
removed from the rear window before driv-
ing. Visibility could otherwise be impaired,
endangering you and others.
iIf the rear window defroster switches off too
soon and the indicator lamp goes out, this indi-
cates that too many electrical consumers are op-
erating simultaneously and the load on the
battery is reducing available voltage. The system
responds automatically by deactivating the rear
window defroster.
iMaximum cooling MAXCOOL is only avail-
able when the engine is running.
Warning!G
Fogged windows impair visibility, endanger-
ing you and others. If the windows begin to
fog on the inside, switching off the air
recirculation mode immediately should clear
interior window fogging. If interior window
fogging persists, make sure the air
conditioning (
page 247) is activated, or
press button;.
iThe air recirculation mode is activated auto-
matically at high outside temperatures.
The indicator lamp on button, is not lit when
the air recirculation mode is automatically acti-
vated.
A quantity of outside air is added when the cool-
ing demand is not at maximum.
If the air conditioning has been turned off
(
page 247) or the outside temperature is be-
low 41°F (5°C), the air recirculation mode will
not switch on automatically.

459 Controls in detail
Automatic climate control
Deactivating: Press button,
(
page 453) up or down.
The indicator lamp on the button goes
out.Air recirculation mode with conve-
nience closing or opening feature
Convenience closing: Press
button
, for approximately
2 seconds.
The side windows and/or tilt/sliding
sunroof will close. You can release
button
, once the closing proce-
dure has begun. The windows and
tilt/sliding sunroof continue closing
until they are fully closed. The indicator
lamp on the button comes on. The air
recirculation mode is activated.
iThe manually selected air recirculation
mode is deactivated automatically:

after 5 minutes if the outside temperature is
below approximately 41°F (5°C)

after 5 minutes if the air conditioning is
turned off

after 30 minutes if the outside temperature
is above approximately 41°F (5°C)
Warning!G
Never operate the side windows and the
tilt/sliding sunroof if there is the possibility
of anyone being harmed by the closing pro-
cedure.
When using the air recirculation mode with
convenience closing feature, should the up-
ward movement of a window be blocked by
some obstruction including but not limited
to arms, hands, fingers, etc., the automatic
reversal feature will not operate.
In the event that the procedure causes po-
tential danger, the closing of the side win-
dows can be immediately halted by pressing
the respective window switch. The closing of
the tilt/sliding sunroof can be immediately
halted by moving the tilt/sliding sunroof
switch in the overhead control panel in any
direction.
The closing of the side windows and the
tilt/sliding sunroof can be reversed by again
pressing and holding button,.


461 Controls in detail
Trunk
Trunk
Opening trunk
You can open the trunk if the vehicle is sta-
tionary.
A minimum height clearance of 5.78 ft
(1.76 m) is required to open the trunk lid.Opening trunk from outside
1Trunk lid handle
Press and hold button Š on the
SmartKey or SmartKey with
KEYLESS-GO* until trunk unlocks and
begins to open.
or
Pull on handle1.
In vehicles without KEYLESS-GO*: The
vehicle must be unlocked.Opening trunk from inside
1Remote trunk opening/closing switch
Press and hold switch1 until the
trunk is opened.
The indicator lamp in switch1 comes
on and remains lit until the trunk is
closed.
To interrupt the opening procedure:
Release switch1.
Warning!G
Make sure the trunk is closed when the en-
gine is running and while driving. Among
other dangers such as blocked visibility,
deadly carbon monoxide (CO) gases may
enter the vehicle interior resulting in
unconsciousness and death.
!The trunk lid swings open upwards automat-
ically. Always make sure that there is sufficient
overhead clearance.
To stop the opening procedure, press
buttonŠ on the SmartKey or SmartKey with
KEYLESS-GO*.

462 Controls in detail
Trunk
Trunk opening-height restriction
The trunk lid opening height can be limited
when transporting goods on a roof rack
(e.g. presence of an optional MB sport lug-
gage container). When activated, the trunk
opens to approximately the height of the
roof edge.
Activate the limiting opening height of
trunk lid using the COMAND system
(
page 242).
Closing trunkClosing trunk from inside automatically
1Remote trunk opening/closing switch
Press and hold switch1 until the
trunk is closed.
The indicator lamp in the switch goes
out when the trunk is closed.
To interrupt the closing procedure:
Release switch1.
iDo not place the SmartKey in the open
trunk. You may lock yourself out.
iIf the vehicle was previously centrally
locked, the trunk will lock automatically after
closing it. All turn signal lamps flash three times
to confirm locking.
Vehicles with KEYLESS-GO*: To prevent a possi-
ble inadvertent lockout, the trunk will open auto-
matically if a SmartKey with KEYLESS-GO* is
recognized inside the vehicle or in the trunk.
The vehicle is only locked when the turn signals
flash three times. If you are carrying a second SmartKey with KEYLESS-GO* with you, you can
still lock the vehicle.
Warning!G
Maintain sight of trunk area while operating
door mounted switch. Monitor the closing
procedure carefully to make sure no one is
in danger of being injured.
To interrupt the closing procedure, release
the door mounted remote trunk open-
ing/closing switch.
Even with the SmartKey or SmartKey with
KEYLESS-GO* removed from the starter
switch or the SmartKey with KEYLESS-GO*
removed from the vehicle, the remote trunk
opening/closing switch can be operated.
Therefore, do not leave children unattended
in the vehicle, or with access to an unlocked
vehicle. A child’s unsupervised access to a
vehicle could result in an accident and/or
serious personal injury.
iIf the trunk lid comes into contact with an
object while closing (e.g. luggage that has been
piled too high) in the upper motion sequence, the
closing procedure is stopped and the trunk re-
opens slightly.
iYou can also close the trunk by hand.

463 Controls in detail
Trunk
Closing trunk from outside
automatically
Vehicles without KEYLESS-GO*
1Trunk closing switch
Vehicles with KEYLESS-GO*
1Trunk closing switch
Press trunk closing switch1 briefly.
The trunk closes.
Warning!G
Monitor the closing procedure carefully to
make sure no one is in danger of being in-
jured. To prevent possible personal injury,
always keep hands and fingers away from
the trunk lid opening when closing the trunk.
Be especially careful when small children
are around. To stop the closing procedure,
do one of the following:

press button Š on the SmartKey or
SmartKey with KEYLESS-GO

press the trunk opening/closing switch
(on the driver’s door)

press the trunk closing switch

press the KEYLESS-GO locking/closing
switch*

pull the trunk lid handle
Even with the SmartKey or SmartKey with
KEYLESS-GO* removed from the starter
switch or the SmartKey with KEYLESS-GO*
removed from the vehicle, the remote trunk
opening/closing switch can be operated.
Therefore, do not leave children unattended
in the vehicle, or with access to an unlocked
vehicle. A child’s unsupervised access to a
vehicle could result in an accident and/or
serious personal injury.
iIf the trunk lid comes into contact with an
object while closing (e.g. luggage that has been
piled too high) in the upper motion sequence, the
closing procedure is stopped and the trunk re-
opens slightly.
iYou can also close the trunk by hand.