System setting MERCEDES-BENZ CL500 2007 C216 Owner's Guide

115 Control systems
COMAND audio CD/audio DVD/MP3
Switching to audio CD, audio DVD or
MP3 mode
Load CD/DVD (page 111) or
PCMCIA card (
page 112).
or
Select “Audio”
“Audio”, then “CD”,
“DVD-Audio” or “MP3”.
or
Press the M shortcut button once or
twice.Example display in audio CD mode
1Current playback option
2Track number
3Disc number
4Disc name (only if saved on the disc)
5Track name (only if saved on the disc)
6Track time
7Graphic time and track display
8Sound settings
9Medium selection
aTo call up track listing
bDisc type
cPlayback optionsExample display in audio DVD mode
1Current playback option
2Track number
3Disc number
4Disc name (only if saved on the disc)
5Track name (only if saved on the disc)
6Track time
7Graphic time and track display
8Sound settings
9Medium selection
aTo call up track listing
bStop function
cPause (“Play” appears if paused)
dDisc type
ePlayback options
iThe M shortcut button takes you directly
to the previously set disc mode (audio CD,
audio DVD or MP3-CD/DVD). The number of
times you have to press the shortcut button de-
pends on the previously set mode.

116 Control systems
COMAND audio CD/audio DVD/MP3
Example display in MP3 mode
1Current playback option
2Medium type
3Disc number (not on PCMCIA card)
4Track name
5Current folder path
6Current folder
7Track time
8Graphic time and track display
9Sound settings
aMedium selection
bFolder listing
cTrack listing
dPlayback optionsStop function
Stopping playback: Select “Audio”

“Audio”
“DVD-Audio”
“Stop”.
Restarting playback: Select “Audio”

“Audio”
“DVD-Audio”
“Play”.
Playback starts at the beginning of the
DVD.
Pause function
In audio CD, audio DVD and MP3 mode
Pausing playback:
Press F briefly.
Continuing playback: PressF
again briefly.
Only in audio DVD mode
Pausing playback:
Select “Audio”
“Audio”
“DVD-Au-
dio”
“Pause”.
The “Pause” screen changes to “Play”.
Continuing playback: Select “Audio”

“Audio”
“DVD-Audio”
“Play”.
The “Play” screen changes to “Pause”.
iThis function is only available in audio DVD
mode.

119 Control systems
COMAND audio CD/audio DVD/MP3
Setting the audio format
This function lets you choose the audio for-
mat that you would like COMAND to play
and is only available in DVD-Audio mode.
Select “Audio”
“Audio”
“DVD-Au-
dio”
“Group”.
The list of available audio formats appears.
A dot R indicates the format currently se-
lected.
Changing setting: Slide qmr or
rotateymz.
Exiting menu: Slide omp.
Playback options
The following options are available:

“Normal Track Sequence”
Tracks playback in the order on the
disc (e.g. track 1, 2, 3, etc.).

“Random Tracks”
Tracks playback in a random order
(e.g. track 3, 8, 5, etc.).

“Random Folder” (in MP3 mode only)
Tracks in the active folder and any sub-
folders playback in random order.

“Repeat Folder” (in MP3 mode only)
Tracks in the active folder will be re-
peated until you switch the function
off.
Selecting an option: Select “Audio”

“Audio”.
Select “CD”, “DVD-Audio” or “MP3”.
The option list appears. A dot R indi-
cates which option is switched on.
Select an option and press n.
The option is switched on. For all op-
tions except “Normal Track Sequence”,
you will see a corresponding indicator
in the main area.iThe tracks on an audio DVD can be stored in
various audio formats. The number of audio for-
mats depends on the audio DVD.
iThe “Group” menu item cannot be selected
if only one audio format is saved on the DVD.
iThe “Normal Track Sequence” option is au-
tomatically activated when you select a different
medium. If an option is activated, it remains acti-
vated after COMAND is switched on/off.

139 Control systems
COMAND telephone*
Switching from the list to the smart
speller: Select “Back” from the list.
or
Press back button L in the center
console (
page 82).
Changing phone book display in the
list: Select “123” or “ABC”.
The screen changes to telephone num-
ber or name display.Closing the COMAND phone book
In the smart speller, select “Back”.
or
Press back button L in the center
console (
page 82).
Selecting an entry in the COMAND
phone book
Selecting entries using the smart speller
Switch from the list to the smart speller
if necessary.
Changing smart speller language:
Select !.
Select desired language.
Changing smart speller character
set: Select #.
Depending on the previous setting, you
will change to letters with special char-
acters or to numbers with special char-
acters.
Entering characters: Select the char-
acters of the entry you are searching
for one by one.
Deleting individual characters: Se-
lect ) and briefly press n.
Each time you enter or delete a charac-
ter, the closest match will be displayed
at the top of the list.
Deleting an entire entry: Select )
and press and hold n until the entry is
deleted.
Canceling search: Switch from the
smart speller to the list.
The entry at the top of the list is auto-
matically highlighted.
Selecting using the list
If necessary, switch from the smart
speller to the list.
Rotate ymz or slide qmr until the de-
sired entry is highlighted.
iThe following options are available under
“Options” menu item 4:

Displaying details about an entry
(
page 140)

Creating a new entry in the address book
(
page 140)

Deleting an entry (page 142)

Saving a phone book entry from mobile
phone in the address book (
page 142)

Adding a telephone number to an address
book entry (
page 144)

141 Control systems
COMAND telephone*
1Data field
2Input mark (cursor)
3Input characters
Changing data field: Slide qmr re-
peatedly until desired data field is high-
lighted.
or
Select [ or ] repeatedly until de-
sired data field is highlighted.
Entering data into a field: Select all
characters one by one from the input
characters line 3.
Toggling upper and lower case for
the input characters: Select & or
(.
Changing language for the input
characters: Select !.
Select desired language.
Changing character set for the input
characters: Select #.
Depending on the previous setting, you
will change to letters with special char-
acters or to numbers with special char-
acters.
Displaying special characters as in-
put characters: Select !
“Sym-
bols”.
Returning input characters to nor-
mal characters: Select !
the
desired language.
Moving cursor in the data field:
SelectY or Z.
Deleting individual characters:
Select) and briefly press n.
The character to the left of the cursor is
deleted.
Deleting an entire entry: Select )
and press and hold n until the entry is
deleted.
Saving an entry: Select ?.
Canceling an entry: Select “Back”.
If one of the data fields contains data, a
prompt will appear asking whether you
want to save the entry.
Select “Yes” or “No”.
The entry will either be saved or
not, depending on your selection.

159 Control systems
COMAND navigation (introduction)
Basic settings
Map orientation
1Current map orientation
The following may be displayed:

8 = “Heading Up” (the map is dis-
played so that the direction of travel is
always up; the orange point of the icon
points north)

9 = “North Up” (the map view is dis-
played so that north is always up)
Setting map orientation:
Select “Navi”
“Navi”
“Map Dis-
play”.
The map display list appears. A dot R
indicates the current setting.
Select “North Up” or “Heading Up”.
Exiting menu: Slide omp.
The map orientation changes accord-
ingly.Setting POI symbols
You can set which points of interest (POIs)
should be displayed as symbols in the
map. POIs are garages, hotels, movie the-
aters or restaurants, for example.
The following settings are possible:

“Standard symbols” (symbol deter-
mined by the factory settings)

“Personal symbols” (you can determine
the symbols yourself)

“No symbols”
iYou can make the following settings regard-
less of whether route guidance is active or inac-
tive.
iDepending on the map scale on the map,
POI symbols may not be visible on the map al-
though their display is activated. In addition, POI
symbols may be covered by the map’s labels.

160 Control systems
COMAND navigation (introduction)
Adjusting: Select “Navi”
“Navi”

“Map Display”.
The map display list appears. A dot R
indicates the current setting.
Select “Standard symbols”, “Personal
symbols” or “No symbols”.
If you select “Personal symbols”, the
list of POIs appears.
Switching POI symbol display on
or off: Select the desired POI.
The corresponding symbol displays
are switched on or off, depending
on the previous status. A check-
mark indicates which status is ac-
tive. You can switch on the symbol
displays for more than one POI.
Exiting menu: Slide omp or press
back button L in the center console
(
page 82).
Geo-coordinate display
Illustration: map with geo-coordinate dis-
play switched on
1Current height above sea level
2Number of GPS satellites from which
signals for positioning can be received
3Coordinate displayDisplay options with geo-coordinate dis-
play switched on
If the crosshair is displayed on the map
view (map was moved manually), only dis-
play 3 is visible.
It shows either the coordinates of the
crosshair or other data on the crosshair
position, e.g. a street name. The digital
map must contain relevant data in order
for this other data to be displayed.
iThe list shows all symbols that are contained
in the digital map across all states (USA) and/or
provinces (CDN). Not all POIs in all states (USA)
or in all provinces (CDN) are available, however.
Certain POI symbols may not be displayed on the
map, even if the symbol display is switched on. iThere must be sufficient GPS reception for
displays 1, 2 and 3 to be shown. Height dis-
play 1 is an approximation because the naviga-
tion system uses the GPS signals for the
calculation.
iIf there is no crosshair on the map view, dis-
plays 1, 2 and 3 are visible. Display 3
shows the coordinates of the current vehicle po-
sition.

161 Control systems
COMAND navigation (introduction)
Switching the geo-coordinate display on
or off
Select “Navi”
“Navi”
“Map Dis-
play”.
The map display list appears.
Select “Coordinates”.
The geo-coordinate display is switched
on or off, depending on the previous
status. A checkmark indicates which
status is active.
Exiting menu: Slide omp or press
back button L in the center console
(
page 82).Setting route mode
Select “Navi”
“Navi”
“Mode”.
The mode list appears.
Switching mode on or off:
Select desired modes.
Depending on the previous status, the
mode is switched on or off. A check-
mark indicates that the mode is
switched on. It is possible to switch on
more than one mode.
Exiting menu: Slide omp or press
back button L in the center console
(
page 82).
COMAND will verify whether it can in-
corporate the modes if you select them
with route guidance active.
If it can, COMAND calculates a new
route while incorporating the modes
selected.
If it cannot, you will see and hear a cor-
responding message.
Select “OK”.
COMAND calculates a new route.
Only those modes which can be in-
corporated are used.
iThis function allows you to set the following
options for route guidance:

“Minimize Highways”

“Minimize Toll Roads”

“Minimize Tunnels”

“Minimize Ferries/Motorail”

162 Control systems
COMAND navigation system (entering a destination)
The following destination entry options are
available:

Entering a destination by address

Entering a destination from the desti-
nation memory

Entering a destination from the list of
last destinations

Entering a destination from the map

Entering a stopover

Entering a POI
Entering a destination by the address
To enter an address you may proceed as
follows:

Enter state (USA) or province (CDN),
street and town/city

Enter state (USA) or province (CDN),
town/city and street

Enter state (USA) or province (CDN),
town/city and center

Enter state (USA) or province (CDN),
zip code and center

Enter state (USA) or province (CDN),
zip code and streetCalling up the address input menu
Select “Navi”
“Destination”
“Ad-
dress Entry”.
The address input menu appears. It
shows a state (USA) or a province
(CDN). Which state or province is
shown depends on the vehicle’s loca-
tion.
1State (USA) or province (CDN)
Warning!G
For safety reasons, only enter a new desti-
nation when the vehicle is stationary.
iIt is possible to enter a destination regard-
less of whether route guidance is active or inac-
tive.
iIt is not possible to enter an address when
the vehicle has exceeded a certain speed. As
soon as the vehicle speed drops below a certain
value, the function is available again.
iIf Russian or Chinese is set as the system
language, the address must be entered using
Latin letters. Setting the system language
(
page 231).
iAs additional information to the street entry,
you can enter either a house number or an inter-
section.
A zip code entry replaces the town/city entry.

182 Control systems
COMAND navigation system (entering a destination)
Entering a destination from the desti-
nation memory
Select “Navi”
“Destination”

“From Memory”.
The destination memory list appears ei-
ther with or without the input charac-
ters (
page 183). Whether the input
characters appear depends on the
number of entries in the destination
memory.
Destination memory list with input
characters
When this list appears, the input charac-
ters 4 are automatically activated.1Top list entry based on the input data
up to that point
2Characters entered by the user
3Characters automatically added by the
system
4Input characters
5Currently non-selectable characters
6Destination memory list
7Currently selected character
8Currently selectable charactersWhile the characters are being selected as
described below, the top list entry 1 al-
ways shows the destination which best
corresponds to the input data as it has
been entered up to that point.
At the same time, COMAND automatically
supplements characters 2 entered by the
user with appropriate characters 3.
Changing language for the input
characters: Select!.
Select desired language.
Changing character set for the input
characters: Select#.
Depending on the previous setting, you
will change to letters with special char-
acters or to numbers with special char-
acters.
Selecting characters: Slide omp or
rotate ymz.
Confirming character selection:
Press n.
iThe destination memory always contains an
entry called “My Address”. You can save your
home address, for example, under this entry
(
page 206).
iIn the list of input characters 4, you can
only select currently selectable characters.
Which characters are included depends on the
sequence in which you have entered your desti-
nation and the content of the destination memo-
ry.