trailer MERCEDES-BENZ CL550 2008 C216 Owner's Manual

463 Controls in detail
Driving systems
Selecting a normal level
Start the engine.
If indicator lamp2 is on:

Press switch1.
Indicator lamp2 goes out. The vehicle
is adjusted to a normal level.
Suspension tuning
The suspension tuning is set according to:


your driving style


road surface conditions


the vehicle loading


your choice of suspension styleThe program mode selector switch (C/S)
(
page 427) is used to adjust the suspen-
sion tuning:

Start the engine.

Select the desired driving program.
Parktronic system*
Driving program
Suspension tuning
CComfort
comfortable
(default setting)
SSport
sporty
for dynamic driving
Warning!
G
Parktronic is a supplemental system. It is
not intended to, nor does it replace, the
need for extreme care. The responsibility
during parking and other critical maneuvers
always remains with the driver.Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.!
Special attention must be paid to objects
with smooth surfaces or low silhouettes (e.g.
trailer couplings, painted posts, elevated cross-
bars or road curbs). Such objects may not be
detected by the system and can damage the
vehicle.

465 Controls in detail
Driving systems
Front sensors
Rear sensorsMinimum distance
If the system detects an obstacle in this
range, all the distance warning segments
illuminate and you hear a warning signal. If
the obstacle is closer than the minimum
distance, the actual distance may no long-
er be indicated by the system.Warning indicators
Visual signals indicate to the driver the rel-
ative distance between the sensors and an
obstacle.
The warning indicator for the front area is
in the instrument cluster. The warning indi-
cator for the rear area is on the roof liner in
the rear.
1Left side of the vehicle
2Right side of the vehicle
3Readiness indicators
Each warning indicator is divided into five
yellow and two red distance segments for
either side of the vehicle.
If yellow readiness indicators 3 under the
distance segments are lit, Parktronic is
ready to measure.Center
approx. 40 in (100 cm)
Corners
approx. 24 in (60 cm)
Center
approx. 48 in (120 cm)
Corners
approx. 32 in (80 cm)
!
During parking maneuvers, pay special at-
tention to objects located above or below the
height of the sensors (e.g. street curbs, painted
posts, or trailer hitches etc.). The Parktronic sys-
tem will not detect such objects at close range
and damage to your vehicle or the object may
result.
Ultrasonic signals from outside sources (e.g.
truck air brakes, car wash, or jackhammers) may
impair the operation of the Parktronic system.
Center
approx. 8 in (20 cm)
Corners
approx. 6 in (15 cm)

467 Controls in detail
Driving systems

Switching off the Parktronic sys-
tem: Press button 1.
Indicator lamp 2 comes on.

Switching on the Parktronic system:
Press button 1 again.
Indicator lamp 2 goes out.
Parktronic system malfunction
If only the red distance segments illumi-
nate and an acoustic warning sounds,
there is a malfunction in the Parktronic
system. The Parktronic system will auto-
matically switch off after 20 seconds and
the indicator lamp in the Parktronic switch
comes on.

Have the Parktronic system checked
by an authorized Mercedes-Benz
Center as soon as possible.
If only the red distance segments illumi-
nate and no acoustic warning sounds, the
Parktronic system sensors are dirty or
there is an interference from other radio or
ultrasonic signals. The Parktronic system
will automatically switch off after 20 sec-
onds and the indicator lamp in the
Parktronic switch comes on.

Switch off the ignition (
page 365).

Clean the Parktronic system sensors
(page 600).

Switch on the ignition.
or

Check the Parktronic system operation
at another location to rule out interfer-
ence from outside radio or ultrasonic
signals.
Park Assist*
i
The Parktronic system is automatically
switched on when the ignition is switched on
(
page 365).
Warning!
G
Park Assist is a supplemental system. It is
not intended to, nor does it replace, the
need for extreme care. The responsibility
during parking and other critical maneuvers
always remains with the driver.Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.!
Special attention must be paid to objects
with smooth surfaces or low silhouettes (e.g.
trailer couplings, painted posts, elevated cross-
bars or road curbs). Such objects may not be
detected by the system and can damage the
vehicle.

469 Controls in detail
Driving systems
The Park Assist system deactivates at
speeds over approximately 10 mph
(16 km/h). At lower speeds the Parktronic
system turns on again.
Park Assist is also switched off when you
set the automatic transmission to park
positionP or switch off the engine.
While the transmission is in neutral
positionN, Park Assist is switched off if
you secure the vehicle in place with the
electronic.
The Park Assist system monitors the sur-
roundings of your vehicle with four sensors
in the front bumper and two sensors in the
rear bumper.
Range of the sensors
The sensors of the Park Assist system are
integrated in the front and rear bumpers.
Make sure that the bumpers are clear of
dirt, ice and slush in the area of the sen-
sors, as otherwise, Park Assist may not
function properly, see “Cleaning the driv-
ing systems sensors” (
page 601).Front sensors
Rear sensors
i
Due to the sensors’ broad detection range,
it is possible that Park Assist also detects the fol-
lowing obstacles and issues a warning:


obstacles in the ground, e.g. sewer canal
covers, rails, bumps in the road or gutters


obstacles moving upward quickly, e.g. rolling
garage doors
Center
approx. 40 in (100 cm)
Corners
approx. 24 in (60 cm)
Center
approx. 50 in (125 cm)
Corners
approx. 24 in (60 cm)
!
While parking, pay particular attention to ob-
jects over or underneath the sensors, e.g. flower
boxes, an elevated crossbar or a trailer tow
hitch. Park Assist does not detect such nearby
objects. You could otherwise damage the vehicle
or the objects.

472 Controls in detailDriving systemsAdvanced Parking Guidance only shows a
representation of the parking space in the
instrument cluster display as parking space
is first initially measured when driving past.
Subsequent changes to the parking space
are not taken into account, e.g. if the posi-
tion of the vehicle parked in front of or be-
hind the space changes or objects in the
parking space are moved. Moving objects
are not shown, e.g. pedestrians or vehicles
driving past. Advanced Parking Guidance
does not relieve you of the responsibility to
pay attention. If you only rely on Advanced
Parking Guidance, you may cause an acci-
dent and injure yourself and others.
You are always responsible for safety and
must continue to pay attention to your im-
mediate surroundings when parking and
maneuvering.
Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.!
Special attention must be paid to objects
with smooth surfaces or low silhouettes (e.g.
trailer couplings, painted posts, elevated cross-
bars or road curbs). Such objects may not be de-
tected by the system and can damage the
vehicle.
i
USA only:
This device has been approved by the FCC as a
“Vehicular Radar System”. The radar sensor is
intended for use in an automotive radar system
only. Removal, tampering, or altering of the de-
vice will void any warranties, and is not permitted
by the FCC. Do not tamper with, alter, or use in
any non-approved way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
i
Canada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation of the device.
Removal, tampering, or altering of the device will
void any warranties, and is not permitted. Do not
tamper with, alter, or use in any non-approved
way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
!
The operation and functionality of the Ad-
vanced Parking Guidance* can be affected or im-
paired by dirty sensors, especially at times of
snow and ice.
Make sure that the area on the bumpers around
the sensors is free of dirt, ice and/or slush, oth-
erwise Advanced Parking Guidance* may not
function properly, see “Cleaning the driving sys-
tems sensors” (
page 601).


473 Controls in detail
Driving systems
Use Advanced Parking Guidance for park-
ing spaces that are

parallel to the direction of travel


located on straight streets, i.e. not in
curves


on the same level as the street, i.e. not
on sidewalks, for example. Flat curbs
may possibly not be detected by Ad-
vanced Parking Guidance.
Parking instructions:


On narrow streets, drive by the parking
space as close as possible.


Parking spaces that are dirty, over-
grown or located in front of trailers may
not be detected correctly.


Also observe the Park Assist warning
indicator (
page 470) while Advanced
Parking Guidance is active.


How well your vehicle will be parked af-
ter completion of the Advanced Park-
ing Guidance depends on the position
and shape of the vehicles parked in
front of and behind the parking space
as well as the conditions of the imme-
diate surroundings. In certain cases,
Advanced Parking Guidance may guide
you too far into the parking space or
not far enough. If this is the case, can-
cel the parking procedure with Ad-
vanced Parking Guidance and correct
the vehicle position yourself.Detecting a parking space
Advanced Parking Guidance is active when
driving forward. The system operates at a
vehicle speed of up to 25 mph (40 km/h)
and automatically scans for and measures
potential parking spaces on both sides of
the vehicle. At a vehicle speed of below
10 mph (16 km/h), you see the white
parking space symbol as a system display
in the instrument cluster. As soon as Ad-
vanced Parking Guidance has detected a
suitable parking space, the parking space
symbol changes to blue.

478 Controls in detailDriving systemsThe Rear View Camera is in the handle
strip of the trunk lid.
1Rear View CameraView through the camera
i
The image from the Rear View Camera is
shown mirror-inverted on the COMAND display
(
page 33).Warning!
G
Please note that objects which do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck, may appear to be further
away than they actually are. In this case, you
should not use the guide lines to judge dis-
tance. The use of the guide lines to judge
distance increases the risk of impacting the
objects.
Warning!
G
The Rear View Camera is a supplement sys-
tem. It is not intended to, nor does it re-
place, the need for extreme care. The
responsibility during parking and other driv-
ing maneuvers always remains with the driv-
er.
The Rear View Camera may show obstacles
with a distorted perspective, incorrectly or
not at all.

480 Controls in detailDriving systemsSwitching on Rear View Camera
Switch on the ignition (
page 365).

Switch on COMAND (
page 83).

Move gear selector lever to reverse
gearR.
The COMAND display will show the
area behind the vehicle with guide
lines.1Blue guide lines for vehicle width
2Yellow 39 in (1 m) guide line
3Red 10 in (0.25 m) guide line
The red 10 in (0.25 m) guide line3, the
yellow 39 in (1 m) guide line2 corre-
spond to the relevant distance from the
rear of the vehicle. The blue guide line for
vehicle width1 show the required width
for the vehicle.Warning!
G
Use of Rear View Camera can be dangerous
if you are color-blind or have impaired color
vision.
Only use Rear View Camera if you can see
and distinguish all colored guide lines shown
by Rear View Camera on the COMAND dis-
play.i
The Rear View Camera must be activated in
the instrument cluster control system in order
for it to be switched on (
page 298).
Warning!
G
Please note that objects which do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck, may appear to be further
away than they actually are. In this case, you
should not use the guide lines to judge dis-
tance as the use of the guide lines to judge
distance increases the risk of impacting the
objects.
Even when the object you approach is di-
rectly on the ground (and nothing on the ob-
ject extends above the ground beyond the
object’s contours directly touching the
ground) and no objects that do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck are in the path, do not ap-
proach the object on the ground any closer
than red guide line4.

565 Operation
Tires and wheels
Tire and Loading InformationTire and Loading Information placard
1Load limit information on the Tire and
Loading Information placard
The Tire and Loading Information placard
showing the load limit information is
located on the driver’s door B-pillar
(
page 564).

Locate the statement “The combined
weight of occupants and cargo should
never exceed XXX kilograms or XXX
lbs.” on the Tire and Loading Informa-
tion placard.
The combined weight of all occupants,
cargo/luggage and trailer tongue load
(if applicable) should never exceed the
weight referenced in that statement.
Seating capacity
The seating capacity gives you important
information on the number of occupants
that can be in the vehicle. Observe front
and rear seating capacity. The Tire and
Loading Information placard showing the
seating capacity is located on the driver’s
door B-pillar (
page 564).
Warning!
G
Do not overload the tires by exceeding the
specified load limit as indicated on the
Tire and Loading Information placard on the
driver’s door B-pillar. Overloading the tires
can overheat them, possibly causing a
blowout. Overloading the tires can also
result in handling or steering problems, or
brake failure.
i
Data shown on Tire and Loading Information
placard example are for illustration purposes
only. Load limit data are specific to each vehicle
and may vary from data shown in the illustration
below. Refer to Tire and Loading Information
placard on vehicle for actual data specific to your
vehicle.
i
Data shown on Tire and Loading Information
placard example are for illustration purposes
only. Seating data are specific to each vehicle
and may vary from data shown in the illustration
below. Refer to Tire and Loading Information
placard on vehicle for actual data specific to your
vehicle.

566 OperationTires and wheels1Seating capacity information on the
Tire and Loading Information placard
Steps for determining correct load limit
The following steps have been developed
as required of all manufacturers under
Title 49, Code of U.S. Federal Regulations,
Part 575 pursuant to the “National Traffic
and Motor Vehicle Safety Act of 1966”.
Step 1
Locate the statement “The combined
weight of occupants and cargo should
never exceed XXX kg or XXX lbs.” on
your vehicle’s Tire and Loading Infor-
mation placard.Step 2

Determine the combined weight of the
driver and passengers that will be
riding in your vehicle.
Step 3

Subtract the combined weight of the
driver and passengers from
XXX kilograms or XXX lbs.
Step 4

The resulting figure equals the avail-
able amount of cargo and luggage load
capacity. For example, if the “XXX”
amount equals 1400 lbs and there will
be five 150 lbs passengers in your
vehicle, the amount of available cargo
and luggage load capacity is 650 lbs
(1400 – 750 (5 x 150) = 650 lbs).
Step 5

Determine the combined weight of
luggage and cargo being loaded on the
vehicle. That weight may not safely
exceed the available cargo and luggage
load capacity calculated in step 4.Step 6 (if applicable)

If your vehicle will be towing a trailer,
load from your trailer will be trans-
ferred to your vehicle. Consult this
manual to determine how this reduces
the available cargo and luggage load
capacity of your vehicle (
page 568).
The following table shows examples on
how to calculate total and cargo load
capacities with varying seating configura-
tions and number and size of occupants.
The following examples use a load limit
of 1500 lbs. This is for illustration
purposes only. Make sure you are using
the actual load limit for your vehicle stated
on the vehicle’s Tire and Loading Informa-
tion placard (
page 565).