height MERCEDES-BENZ CL550 2010 W216 Owner's Guide

Mounting the spare wheel
Introduction X
Prepare the vehicle as described
(Y page 465).
X Take the following out of the vehicle:
R
spare wheel
R jack
R vehicle tool kit
R wheel bolts for spare wheel
For information on where to find the
respective items, see “Where will I find ...?”
(Y page 412) and ( Y page 413).
i Vehicles without spare wheel are not
factory-equipped with
the tools required for
a wheel change such as a jack or a wheel
wrench. Some tools required for a wheel
change are specific to your vehicle.
Contact an authorized Mercedes-Benz
Center to obtain the tools approved for
your vehicle. This section describes the
wheel change using the tools approved and
recommended for your vehicle.
Lifting the vehicle G
Warning!
When jacking up the vehicle, only use the jack
which has been specifically approved by
Mercedes-Benz for your vehicle.
The jack

is designed exclusively for jacking up
the vehicle at the jack take-up brackets built
into both sides of the vehicle. Make sure the
jack arm is fully seated in the jack take-up
bracket. The jack must always be vertical
when in use, especially on inclines or
declines.
The jack is intended only for lifting the vehicle
briefly for wheel changes. It is not suited for
performing maintenance work under the
vehicle. To help avoid personal injury, use the
jack only to lift the vehicle during a wheel
change. Never get beneath the vehicle while it is
supported by the jack. Keep hands and feet
away from the area under the lifted vehicle.
Always lower the vehicle onto sufficient
capacity
jackstands

before working under the
vehicle.
Always make sure the electronic parking
brake is engaged. In addition, block the
wheels with wheel chocks or other sizeable
objects before raising the vehicle with the
jack. Do not disengage the electronic parking
brake while the vehicle is raised.
Make sure that the ground on which the
vehicle is standing and where you place the
jack is solid, level and not slippery. If
necessary, use a large underlay. On slippery
surfaces, such as tiled floors, you should use
a non-slip underlay, for example a rubber mat.
Do not use wooden blocks or similar objects
to support the jack. Otherwise the jack may
not be able to achieve its load-bearing
capacity if it is not at its full height.
Never start the engine when the vehicle is
raised.
Also observe the notes on the jack.
X Prevent the vehicle from rolling away by
blocking wheels

with wheel chocks or other
sizeable objects.
When your vehicle is equipped with a wheel
chock, it is included with the vehicle tool kit
(Y page 412). For information on setting up
the collapsible wheel chock, see
(Y page 412).
When changing a wheel on a level surface:
X Place a wheel chock or other sizeable
object in

front of and another wheel chock
or other sizeable object behind the wheel
that is diagonally opposite to the wheel
being changed. 466
Flat tire
Practical hints
216_AKB; 3; 90, en-US
d2ureepe,
Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 466

Vehicle specification CL 550 4MATIC
(216.386)
The quoted data apply only to the standard
vehicle. Contact an authorized Mercedes-
Benz Center
for the corresponding data of all
special bodies and special equipment. Engine CL 550 4MATIC
Engine, type
273
Mode of operation
4-stroke engine,
gasoline injection No. of cylinders
8
Bore
3.86 in (98.00 mm)
Stroke
3.56 in (90.50 mm)
Total piston
displacement
333.3 cu in
(5 461 cm 3
) Compression
ratio
10.7:1
Output acc. to
SAE J 1349
36 382 hp/6
000 rpm
(285 kW/6 000 rpm) Maximum torque
acc.
to

SAE J 1349 391 lb-ft/
2 800 - 4 800 rpm
(530 Nm/
2 800 - 4 800 rpm) Maximum engine
speed
6 500 rpm
Firing order
1-5-4-2-6-3-7-8
Poly-V-belt
2 404 mm
Electrical system CL 550 4MATIC
Alternator
14 V/180 A
Starter motor
12 V/1.7 kW
Battery
12 V/95 Ah Electrical system CL 550 4MATIC
Spark plugs, type
NGK PLKR 7A
Bosch Y 7 MPP33
Spark plugs,
electrode gap
0.031 in (0.8 mm)
Spark plugs,
tightening torque
15 - 18 lb-ft
(20 - 25 Nm) Main dimensions CL 550 4MATIC
Overall vehicle
length
199.7 in (5
071 mm) Overall vehicle
width
37 84.2 in (2
139 mm) Overall vehicle
height
55.8 in (1
418 mm) Wheelbase
116.3 in (2
955 mm) Track, front
63.0 in (1
601 mm) Track, rear
63.3 in (1
607 mm) Turning circle
38.1 ft (11.6 m)
Weights CL 550 4MATIC
Trunk load
max. 220 lb (100 kg)
Vehicle specification CL 600
(216.376)
The quoted data apply only to the standard
vehicle. Contact an authorized Mercedes-
Benz Center

for the corresponding data of all
special bodies and special equipment.
36 Premium fuel required. Performance may vary with fuel octane rating.
37 Exterior rear view mirrors folded out. Vehicle specification CL 600 (216.376)
483
Technical data
216_AKB; 3; 90, en-US
d2ureepe, Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 483 Z

Engine CL 600
Engine, type
275
Mode of operation
4-stroke engine,
gasoline injection No. of cylinders
12
Bore
3.23 in (82.00 mm)
Stroke
3.43 in (87.00 mm)
Total piston
displacement
336.4 cu in
(5 513 cm 3
) Compression
ratio
9.0:1
Output acc. to
SAE J 1349
38 510 hp/5
000 rpm
(380 kW/5 000 rpm) Maximum torque
acc.
to
SAE J 1349 612 lb-ft/
1 800 - 3 500 rpm
(830 Nm/
1 800 - 3 500 rpm) Maximum engine
speed
5 950 rpm
Firing order
1-12-5-8-3-10-
6-7-2-11-4-9 Poly-V-belt
2 370 mm
Electrical system CL 600
Alternator
14 V/220 A
Starter motor
12 V/2.0 kW
Battery
12 V/95 Ah
Spark plugs, type
NGK IFR 6Q-G
Spark plugs,
electrode gap
0.028 in (0.7 mm)
Spark plugs,
tightening torque
15 - 22 lb-ft
(20 - 30 Nm) Main dimensions CL 600
Overall vehicle
length
199.7 in (5
071 mm) Overall vehicle
width
39 84.2 in (2
139 mm) Overall vehicle
height
55.9 in (1
419 mm) Wheelbase
116.3 in (2
955 mm) Track, front
63.0 in (1
601 mm) Track, rear
63.3 in (1
607 mm) Turning circle
38.1 ft (11.6 m)
Weights CL 600
Trunk load
max. 220 lb (100 kg)
Vehicle specification CL 63 AMG
(216.377)
The quoted data apply only to the standard
vehicle. Contact an authorized Mercedes-
Benz Center

for the corresponding data of all
special bodies and special equipment. Engine CL 63 AMG
Engine, type
156
Mode of operation
4-stroke engine,
gasoline injection No. of cylinders
8
Bore
4.02 in (102.20 mm)
Stroke
3.72 in (94.60 mm)
Total piston
displacement
378.8 cu in
(6 208 cm 3
) 38
Premium fuel required. Performance may vary with fuel octane rating.
39 Exterior rear view mirrors folded out. 484
Vehicle specification CL 63 AMG (216.377)
Technical data
216_AKB; 3; 90, en-US
d2ureepe,
Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 484

Engine CL 63 AMG
Compression
ratio
11.3:1
Output acc. to
SAE J 1349
40 518 hp/6
800 rpm
(386 kW/6 800 rpm) Maximum torque
acc. to
SAE J 1349 465 lb-ft/5
200 rpm
(630 Nm/5 200
rpm) Maximum engine
speed
7 200 rpm
Firing order
1-5-4-2-6-3-7-8
Poly-V-belt
2 360 mm
Electrical system CL 63 AMG
Alternator
14 V/220 A
Starter motor
12 V/2.1 kW
Battery
12 V/95 Ah
Spark plugs, type
NGK ILZKAR 7A10
Spark plugs,
electrode gap
0.039 in (1.0 mm)
Spark plugs,
tightening torque
18 - 22 lb-ft
(25 - 30 Nm) Main dimensions CL 63 AMG
Overall vehicle
length
200.4 in (5
090 mm) Overall vehicle
width
41 84.2 in (2
139 mm) Overall vehicle
height
56.1 in (1
426 mm) 42 56.2 in (1
428 mm) 43 Wheelbase
116.3 in (2
955 mm) Main dimensions CL 63 AMG
Track, front
63.0 in (1
601 mm) Track, rear
63.3 in (1
607 mm) Turning circle
38.1 ft (11.6 m)
Weights CL 63 AMG
Trunk load
max. 220 lb (100 kg)
Vehicle specification CL 65 AMG
(216.379)
The quoted data apply only to the standard
vehicle. Contact an authorized Mercedes-
Benz Center

for the corresponding data of all
special bodies and special equipment. Engine CL 65 AMG
Engine, type
275
Mode of operation
4-stroke engine,
gasoline injection No. of cylinders
12
Bore
3.25 in (82.60 mm)
Stroke
3.66 in (93.00 mm)
Total piston
displacement
364.9 cu in
(5 980 cm 3
) Compression
ratio
9.0:1
Output acc. to
SAE J 1349
44 603 hp/
4 800 - 5 100 rpm
(450 kW/
4 800 - 5 100 rpm) 40
Premium fuel required. Performance may vary with fuel octane rating.
41 Exterior rear view mirrors folded out.
42 Vehicles with 19 in rims.
43 Vehicles with 20 in rims.
44 Premium fuel required. Performance may vary with fuel octane rating. Vehicle specification CL 65 AMG (216.379)
485
Technical data
216_AKB; 3; 90, en-US
d2ureepe,Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 485 Z

Engine CL 65 AMG
Maximum torque
acc.
to
SAE J 1349 738 lb-ft/
2 000 - 4 000 rpm
(1 000 Nm/
2 000 - 4 000 rpm) Maximum engine
speed
5 950 rpm
Firing order
1-12-5-8-3-10-
6-7-2-11-4-9 Poly-V-belt
2 370 mm
Electrical system CL 65 AMG
Alternator
14 V/220 A
Starter motor
12 V/1.7 kW
Battery
12 V/95 Ah
Spark plugs, type
NGK IFR 6Q-G
Spark plugs,
electrode gap
0.028 in (0.7 mm)
Spark plugs,
tightening torque
15 - 22 lb-ft
(20 - 30 Nm) Main dimensions CL 65 AMG
Overall vehicle
length
200.4 in (5
090 mm) Overall vehicle
width
45 84.2 in (2
139 mm) Overall vehicle
height
56.1 in (1
426 mm) 46 56.2 in (1
428 mm) 47 Wheelbase
116.3 in (2
955 mm) Track, front
63.0 in (1
601 mm) Track, rear
63.3 in (1
607 mm) Turning circle
38.1 ft (11.6 m) Weights CL 65 AMG
Trunk load
max. 220 lb (100 kg)
Rims and tires
Notes
! Only use

tires which have been tested and
approved by Mercedes-Benz. Tires
approved by Mercedes-Benz are developed
to provide best possible performance in
conjunction with the driving safety systems
on your vehicle such as the ABS or the ESC.
Tires specially developed for your vehicle
and tested and approved by Mercedes-
Benz can be identified by finding the
following on the tire’s sidewall:
R MO = Mercedes-Benz Original
equipment tires
Using tires other than those approved by
Mercedes-Benz may result in damage that
is not covered by the Mercedes-Benz
Limited Warranty.
! Using tires other than those approved by
Mercedes-Benz can have detrimental
effects, such as
R poor handling characteristics
R increased noise
R increased fuel consumption
Moreover, tires and rims not approved by
Mercedes-Benz may, under load, exhibit
dimensional variations and different tire
deformation characteristics that could
cause them to come into contact with the
vehicle body or axle parts. Damage to the
tires or the vehicle may be the result.
i Further information on tires and rims is
available at

any authorized Mercedes-Benz
Center. The Tire and Loading Information
45 Exterior rear view mirrors folded out.
46 Vehicles with 19 in rims.
47 Vehicles with 20 in rims. 486
Rims and tires
Technical data
216_AKB; 3; 90, en-US
d2ureepe,
Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 486