lights MERCEDES-BENZ CL600 2004 C215 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2004, Model line: CL600, Model: MERCEDES-BENZ CL600 2004 C215Pages: 418, PDF Size: 4.53 MB
Page 16 of 418
15 Introduction
Symbols
Symbols
The following symbols are found in this
Operator’s Manual:
* Optional equipment is identified
with an asterisk. Since standard
equipment varies between models,
the descriptions and illustrations in
this manual may differ slightly from
the actual equipment of your vehi-
cle.
This symbol points to instructions for
you to follow.
A number of these symbols appearing
in succession indicates a multiple-step
procedure.
Page This symbol tells you where to
look for further information on a
topic.
This continuation symbol marks
an interrupted procedure which
will be continued on the next
page.
-> In the glossary of technical
terms, this symbol is used to in-
dicate cross-references to term
definitions.
DISPLAY
Words appearing in the multi-
function display are printed in
the type shown here.
Warning!
G
Warning notices draw your attention to haz-
ards that may endanger your health or life,
or the health or life of others.!Highlights hazards that may result in
damage to your vehicle.iHelpful hints or further information you
may find useful.
Page 57 of 418
56 Getting startedParking and lockingFor more information, see “Locking and
unlocking” (
page 88).Turning off the engine with
KEYLESS-GO*
Place the gear selector lever in
positionP.
Press the KEYLESS-GO start/stop but-
ton to shut off the engine.
With the driver's door closed, the start-
er switch is now in position1. With the
driver’s door opened, the starter switch
is set to position0, same as SmartKey
removed from starter switch
(page 31).
Press the seat belt release button
(page 44).
Allow the retractor to completely re-
wind the seat belt by guiding the latch
plate.
Warning!
G
When leaving the vehicle, always remove the
SmartKey from the starter switch and lock
your vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. Unsupervised use of vehi-
cle equipment may cause an accident
and/or serious personal injury.
!If you hear a warning signal, you have
either
forgotten to turn off the lights be-
fore opening the driver’s door
or
tried to turn off the engine while the
gear selector lever is not inP .
Turn off the lights or place the gear se-
lector lever inP.
iOpening a door causes the windows on
that side of the car to open slightly.
They will return to the up position when
the door is closed.
Page 121 of 418
120 Controls in detailLightingTo activate the daytime running lamp
mode, see “Setting daytime running lamp
mode (USA only)” (
page 150).Manual headlamp mode
The low beam headlamps and parking
lamps can be switched on and off with the
exterior lamp switch. For exterior lamp
switch, see (
page 119).
Automatic headlamp mode
The parking lamps, low beam headlamps
and license plate lamps switch on and off
automatically depending on the brightness
of the ambient light.
Turn the exterior lamp switch to U.
iIf you remove the SmartKey and open
the driver’s door while the parking
lamps or low beam headlamps are
switched on, then:
a warning sounds
$ appears in the multifunction
display
the message
SWITCH OFF LIGHTS!
appears in the multifunction display
iWith the daytime running lamp mode
activated and the engine running, the
low beam headlamps cannot be
switched off manually.
Warning!
G
If the exterior lamp switch is set toU,
the headlamps may switch off unexpect-
edly when the system senses bright am-
bient light, for example light from
oncoming traffic.
the headlamps will not be automatically
switched on under foggy conditions.
To minimize risk to you and to others, acti-
vate headlamps by turning exterior lamp
switch to B when driving or when traffic
and / or ambient lighting conditions require
you to do so.
In low ambient lighting conditions, only
switch from position U to B with the
vehicle at a standstill. Switching from U
to B will briefly switch off the head-
lamps. Doing so while driving in low ambient
lighting conditions may result in an acci-
dent.
The automatic headlamp feature is only an
aid to the driver. The driver is responsible for
the operation of the vehicle's lights at all
times.
Page 150 of 418
149 Controls in detail
Control system
Selecting language
Move the selection marker with
theæ orç button to the
INST.
CLUS.
submenu.
Press buttonj ork repeatedly
until you see this message in the dis-
play:
TEXT
The selection marker is on the current
setting.
Pressæ orç to select the lan-
guage to be used for the multifunction
display messages.
Available languages:
German
English
French
Italian
SpanishLighting submenu
Access the
LIGHTING
submenu via the
SET-
TINGS
menu. Use the
LIGHTING
submenu
to change the lamp and lighting settings on
your vehicle. The following functions are
available:
Function
Page
Set daytime running lamp mode
(USA only)
150
Set locator lighting
150
Exterior lights delayed shut-off
151
Interior lighting delayed shut-off
152
Page 152 of 418
151 Controls in detail
Control system
The locator lighting switches off when the
driver’s door is opened. It switches off au-
tomatically after a period of approximately
40 seconds.
Move the selection marker with
theæ orç button to the
LIGHT-
ING
submenu.
Press buttonj ork repeatedly
until you see this message in the dis-
play:
LOCATOR LIGHTING
.
The selection marker is on the current
setting.
Pressæ orç to select the de-
sired setting.
The locator lighting will be switched
ON
or
OFF
.Setting night security illumination
(Exterior lights delayed switch-off)
Use the
HEADLAMPS DELAYED SWITCH-OFF
function to set whether and for how long
you would like the exterior lamps to illumi-
nate during darkness after all doors are
closed. When the delayed switch-off fea-
ture is activated and the exterior lamp
switch is in position U before the en-
gine is turned off, the following lamps will
remain lit after you remove the SmartKey
from the starter switch:
Parking lamps
Tail lamps
License plate lamps
Front fog lampsTo activate night security illumination:
Select delayed switch-off period (see
below).
Turn the exterior lamp switch to
positionU before turning off the en-
gine.
To select delayed switch-off period:
Move the selection marker with
theæ orç button to the
LIGHT-
ING
submenu.
Press buttonj ork repeatedly
until you see this message in the dis-
play:
HEADLAMPS DELAYED SWITCH-OFF
.
The selection marker is on the current
setting.
iYou can reactivate this function within
ten minutes by opening a door.
If you do not open a door after remov-
ing the SmartKey, the lamps will auto-
matically shut off after 60 seconds.
Page 318 of 418
317 Practical hints
What to do if …?
Display symbol
Display messages
Possible cause
Possible solution
.
SWITCH OFF LIGHTS!
Lamps have been turned on although the
SmartKey in the starter switch is in
position0.
Turn off the headlamps.
TURN SIGNAL F, L
CHECK LAMP!
SUBSTITUTE LAMP ON!
The left front turn signal lamp is malfunc-
tioning. A back-up bulb is being used.
Replace the bulb as soon as possible.
TURN SIGNAL F, R
CHECK LAMP!
SUBSTITUTE LAMP ON!
The right front turn signal lamp is mal-
functioning. A back-up bulb is being used.
Replace the bulb as soon as possible.
TURN SIGNAL, L
CHECK LAMP!
SUBSTITUTE LAMP ON!
The left rear turn signal lamp is malfunc-
tioning. A back-up bulb is being used.
Replace the bulb as soon as possible.
TURN SIGNAL, R
CHECK LAMP!
SUBSTITUTE LAMP ON!
The right rear turn signal lamp is malfunc-
tioning. A back-up bulb is being used.
Replace the bulb as soon as possible.
TURN SIG. MIRROR, L
CHECK LAMP!
The left turn signal in the side mirror is
malfunctioning. This message will only
appear if all light emitting diodes have
stopped working.
Visit an authorized Mercedes-Benz Cen-
ter as soon as possible.
Page 338 of 418
337 Practical hints
Replacing bulbs
Rear lamps Notes on bulb replacement
Only use 12 volt bulbs of the same type
and with the specified watt rating.
Switch lights off before changing a bulb
to prevent short circuits.
Always use a clean lint-free cloth when
handling bulbs.
Your hands should be dry and free of oil
and grease.
If the newly installed bulb does not
come on, visit an authorized
Mercedes-Benz Center.
Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Center:
Additional turn signal lamps in the
exterior rear view mirrors
Bi-Xenon lamps
Front fog lamps
High mounted brake lamp
Brake lamp
Rear side marker
Lamp
Type
8
High mounted brake
lamp
LED
9
Brake lamp
LED
a
Tail, parking and
standing lamp
P 21/4 W
Side marker lamp
LED
b
Backup lamp
P21W
c
License plate lamps
C5W
d
Rear fog lamp,
driver’s side
P 21/4 W
e
Turn signal lamp
PY 21 W
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can get very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas. A
bulb can explode if you
touch or move it when hot
drop the bulb
scratch the bulb
Wear eye and hand protection.
Because of high voltage in Bi-Xenon lamps,
it is dangerous to replace the bulb or repair
the lamp and its components. We recom-
mend that you have such work done by a
qualified technician.
Page 339 of 418
338 Practical hintsReplacing bulbsReplacing bulbs for front lamps
1Housing cover for high beam flasher
bulb, parking and standing lamp2Electrical connector for high beam
flasher housing bulb
3Parking and standing lamp
4Bulb socket for turn signal lamp
5Bi-Xenon (low and high beam) housing
coverBi-Xenon headlamp
High beam flasher bulb
Switch off the lights.
Open the hood (
page 260).
Press ends of housing cover1 tab to-
gether and remove cover.
Press connector2 downward.
Remove connector2 with the bulb.Warning!
G
Do not remove the cover for the Bi-Xenon
headlamp. Because of high voltage in Xenon
lamps, it is dangerous to replace the bulb or
repair the lamp and its components. We rec-
ommend that you have such work done by a
qualified technician.
Page 340 of 418
339 Practical hints
Replacing bulbs
Insert the new bulb so that the base lo-
cates in the recess on the holder.
From below, press connector2 with
bulb upward onto the reflector.
Align housing cover1 and click into
place.
Front turn signal bulb
Switch off the lights.
Open the hood (
page 260).
Twist bulb socket4 counterclockwise
and pull out.
Gently push bulb into socket, turn
counterclockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinsert bulb socket in lamp and twist
clockwise.Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 260).
Press ends of housing cover1 tab to-
gether and remove cover.
Pull out the bulb socket with the bulb.
Pull the bulb out of the bulb socket.
Insert a new bulb in the socket.
Reinstall the bulb socket.
Align housing cover and click into
place.Side marker lamp bulb
Switch off the lights.
Carefully slide lamp towards rear.
Remove front end first.
Twist bulb socket counterclockwise
and pull out.
Pull bulb out of the bulb socket.
Insert new bulb in socket.
Reinstall bulb socket, push in and twist
clockwise.
To reinstall lamp, set rear end in
bumper and let front end snap into
place.
Page 341 of 418
340 Practical hintsReplacing bulbsReplacing bulbs for rear lamps
Tail lamp assemblies
1Backup lamp (black socket)
2Turn signal lamp (white socket)
3Tail, standing and parking lamp (red
socket)
4Driver’s side: tail, parking and rear fog
lamp
Passenger’s side: tail and parking lamp
(red socket)
Switch off lights.
Open trunk.
Turn lock counterclockwise and move
the trim to the side.
Turn bulb socket counterclockwise and
pull out.
Gently twist bulb counterclockwise and
pull out of bulb holder.
Insert new bulb into the holder and turn
it clockwise.
Reinstall bulb socket.
The bulb socket should audibly click.
Replace trim and secure with lock. License plate lamp
1Screws
Switch off the lights.
Loosen both screws1 and remove
lamp.
Replace the tubular lamp and reinstall
it.
Retighten the screws.