sensor MERCEDES-BENZ CL600 2006 C215 User Guide

294 OperationTires and wheelsChecking tire inflation pressure
Regularly check your tire inflation pressure
at least once a month.
Check and adjust the tire inflation
pressure when the tires are cold. The tires
can be considered cold if the vehicle has
been parked for at least 3 hours or driven
less than 1 mile (1.6 km).
If you check the tire inflation pressure
when the tires are warm (the vehicle has
been driven for several miles or sitting less
than 3 hours), the reading will be
approximately 4 psi (0.3 bar) higher than
the cold reading. This is normal. Do not let
air out to match the specified cold tire in-
flation pressure. Otherwise, the tire will be
underinflated.Checking tire inflation pressure
manually
Follow the steps below to achieve correct
tire inflation pressure:

Remove the cap from the valve on one
tire.

Firmly press a tire gauge onto the
valve.

Read tire inflation pressure on tire
gauge and check against the recom-
mended tire inflation pressure on the
placard on the driver’s door B-pillar
(page 292). If necessary, add air to
achieve the recommended tire inflation
pressure.

Install the valve cap.

Repeat this procedure for each tire.
Checking tire inflation pressure
electronically*
The tire inflation pressure monitor only
functions on wheels that are equipped with
the proper electronic sensors. It monitors
the tire inflation pressure, as selected by
the driver, in all four tires. A warning is
issued to alert you to a decrease in tire
inflation pressure in one or more of the
tires.
You can call up the tire inflation pressure
monitoring display using the control
system (
page 137).
iIf you have overfilled the tire, release
tire inflation pressure by pushing the
metal stem of the valve with e.g. a tip of
a pen. Then recheck the tire inflation
pressure with the tire gauge.

321 Operation
Vehicle care
Ornamental moldings
For regular cleaning and care of ornamen-
tal moldings, use a damp cloth.Headlamps, tail lamps, side markers,
turn signal lenses

Use a mild car wash detergent, such as
Mercedes-Benz approved Car
Shampoo, with plenty of water.
!Due to the width of the vehicle, fold in
exterior rear view mirrors prior to run-
ning the vehicle through an automatic
car wash to prevent damage to the
mirrors.
Make sure that the windshield wiper
switch is set to0 (
page 54). Other-
wise, the rain sensor could activate and
cause the wipers to move unintention-
ally. This may lead to vehicle damage.
iAfter running the vehicle through an au-
tomatic car wash, wipe any wax off of
the windshield (
page 323). This will
prevent smears and reduce wiping
noise which can be caused by residual
wax on the windshield.
When leaving the car wash, make sure
that the mirrors are folded out. Other-
wise they may vibrate.
!Do not use chrome cleaner on orna-
mental moldings. Although ornamental
moldings may have chrome appear-
ance, they could be made of anodized
aluminum that will be damaged when
cleaned with chrome cleaner. Instead,
use a damp cloth to clean those orna-
mental moldings.
For very dirty ornamental moldings of
which you are sure are chrome-plated,
use a chrome cleaner. If in doubt
whether an ornamental molding is
chrome-plated, contact an authorized
Mercedes-Benz Center.
!Only use window cleaning solutions
that are suitable for plastic lamp lens-
es. Window cleaning solutions which
are not suitable may damage the plas-
tic lamp lenses of the headlamps.
Therefore, do not use abrasives, sol-
vents or cleaners that contain solvents.
Never apply strong force and only use a
soft, non-scratching cloth when clean-
ing the lenses. Do not attempt to wipe
dirty lenses with a dry cloth or sponge.
Otherwise you may scratch or damage
the lens surface.

322 OperationVehicle careCleaning the Distronic* system sensor
cover
1Distronic system sensor cover
Switch off the ignition (
page 34).

Use a mild car wash detergent, such as
Mercedes-Benz approved Car
Shampoo, with plenty of water and a
non-scratching cloth to clean sensor
cover1.Cleaning the Parktronic* system
sensors
1Parktronic system sensors in front
bumper

Use a mild car wash detergent, such as
Mercedes-Benz approved Car
Shampoo, with plenty of water and a
soft, non-scratching cloth to clean
sensors1 on the bumpers.
!To prevent scratches or damage, never
apply strong force and only use a soft,
non-scratching cloth when cleaning the
sensor cover1. Do not attempt to
wipe dirty sensors with a dry cloth or
sponge.
!Do not apply strong pressure to the
sensor covers. Applying strong pres-
sure may damage the sensor covers.
Follow the instructions provided by the
power washer manufacturer on main-
taining a distance between the vehicle
and the nozzle of the power washer.!To prevent scratches, never apply
strong force and only use a soft,
non-scratching cloth when cleaning the
sensors. Do not attempt to wipe dirty
sensors with a dry cloth or sponge.

352 Practical hintsWhat to do if …?When the message:ADD 1.0 QT. OIL
AT FILLING STATION(Canada:
1.0 LITER
)
appears while the engine is running and at
operating temperature, the engine oil level
has dropped to approximately the mini-
mum level.When this occurs, the warning will first
come on intermittently and then stay on if
the oil level drops further.
Visually check for oil leaks. If no obvious oil
leaks are noted, drive to the nearest ser-
vice station where the engine oil should be
topped to the required level with an ap-
proved oil specified in the Factory
Approved Service Products pamphlet.
Display
Possible cause/consequence
Possible solution
:
ENGINE OIL LEVEL
VISIT WORKSHOP
The engine oil has dropped to a critical
level.

Check the engine oil level (
page 275)
and add engine oil as required
(
page 278).

If you must add engine oil frequently,
have the engine checked for possible
leaks.
There is water in the engine oil.

Have the engine oil checked.
OIL SENSOR MALFUNCT.
VISIT WORKSHOP
The measuring system is malfunctioning.

Have the measuring system checked by
an authorized Mercedes-Benz Center.
!The engine oil level warnings should
not be ignored. Extended driving with
the symbol displayed could result in
serious engine damage that is not
covered by the Mercedes-Benz Limited
Warranty.

356 Practical hintsWhat to do if …?Display
Possible cause/consequence
Possible solution
.
LIGHT SENSOR
DRIVE TO WORKSHOP
The lamp sensor is malfunctioning. The
headlamps switch on automatically.

In the control system, set lamp operation
to manual (
page 159).

Switch on headlamps using the exterior
lamp switch.

Visit an authorized Mercedes-Benz
Center as soon as possible.
LOW BEAM, LEFT
CHECK LIGHT
The left low beam lamp is malfunctioning.

Visit an authorized Mercedes-Benz
Center as soon as possible.
LOW BEAM, RIGHT
CHECK LIGHT
The right low beam lamp is malfunction-
ing.

Visit an authorized Mercedes-Benz
Center as soon as possible.
MARKER LIGHT, FL
CHECK LIGHT

The front left side marker lamp is mal-
functioning.

Visit an authorized Mercedes-Benz
Center as soon as possible.
MARKER LIGHT, FR
CHECK LIGHT

The front right side marker lamp is mal-
functioning.

Visit an authorized Mercedes-Benz
Center as soon as possible.

362 Practical hintsWhat to do if …?Display
Possible cause/consequence
Possible solution
TIRE PRES. MONITOR
CURRENTLY
UNAVAILABLE
The tire inflation pressure monitor* is un-
able to monitor the tire inflation pressure
due to:

the presence of several wheel sensors
in the vehicle


excessive wheel sensor temperatures


a nearby radio interference source


unrecognized wheel sensors installed

Remove any extra wheel sensors from the
vehicle.
As soon as the causes of the malfunction have
been removed, the tire inflation pressure moni-
tor automatically becomes active again.
TIRE PRES. MONITOR
NOT OPERATIONAL
DRIVE TO WORKSHOP
The tire inflation pressure monitor or a
wheel sensor is malfunctioning.

Have the tire inflation pressure monitor
checked by an authorized Mercedes-Benz
Center.
A wheel without proper sensor was in-
stalled.

Have the wheels checked.
Warning!
G
Do not drive with a flat tire. A flat tire affects
the ability to steer or brake the vehicle.
You may lose control of the vehicle. Contin-
ued driving with a flat tire will cause exces-
sive heat build-up and possibly a fire.

427 Technical terms
ABC
(A
ctive B
ody C
ontrol)
Active, computer-controlled system
that hydraulically adjusts the suspen-
sion at all four wheels in response to
various driving situations.
ABS
(A
ntilock B
rake S
ystem)
Prevents the wheels from locking up
during braking so that the vehicle can
continue to be steered.
Accessory weight
(
page 309)
Air pressure
(page 309)
Alignment bolt
Metal pin with thread. The centering
pin is an aid used when changing a tire
to align the wheel with the wheel hub.
Aspect ratio
(page 309)BabySmart
TM air bag deactivation
system
This system detects if a special system
compatible child restraint seat is in-
stalled on the front passenger seat. The
system will automatically deactivate
the passenger front air bag when such
a seat is properly installed
(the58indicator lamp in the
center console comes on and remains
illuminated).
BabySmartTM compatible child seats
Special restraint system for children.
The sensor system for the front pas-
senger seat prevents deployment of
the passenger front air bag if a
BabySmartTM compatible child seat is
installed. See an authorized
Mercedes-Benz Center for availability.
Bar
(
page 309)BAS
(B
rake A
ssist S
ystem)
System for potentially reducing braking
distances in emergency braking situa-
tions. The system is activated when it
senses an emergency based on how
fast the brake is applied.
Bead
(
page 309)
Bi-Xenon headlamps
Headlamps which use an electric arc as
the light source and produce a more in-
tense light than filament headlamps.
Bi-Xenon headlamps produce low
beam and high beam.
CAC
(Customer A
ssistance C
enter)
Mercedes-Benz customer service cen-
ter, which can help you with any ques-
tions about your vehicle and provide
assistance in the event of a break-
down.

436 IndexD
Daytime running lamp mode 127
Setting 159
Deep water see Standing water
Defogging windshield 188
Defrosting, Front 189
Defrosting, Rear 193
Delayed switch-off
Exterior lights 160
Interior illumination 161
Department of Transportation see DOT
Difficulties
While driving 56
With starting 50
Digital clock see Clock
Digital speedometer 142
Dimensions, Vehicle 417
Direction of rotation, Tires 286
Displays
Digital speedometer 142
Maintenance service indicator 315
Messages in display 337
Multifunction display 137
Outside temperature 25, 136, 157Showing malfunctions 153
Symbol messages 345
Text messages 339
Vehicle status messages 153, 337
Vehicle system settings, Control
system 137
Distance to empty (Range) 152
Distronic* 150, 208, 428
Activating/deactivating 213
Cleaning system sensor 322
Control system 150
Distance warning function 216
Driving hints 217
Menu 211
Messages in display 342
Sensor cover 322
Warning and indicator lamps 210
Warning sounds 216, 332
Document holder 230
Door
Entry lamps 133
Inside door handle 30, 100
Locking/unlocking, SmartKey 60, 90
Locking/unlocking, SmartKey with
KEYLESS-GO* 60, 94Message in display 350
Opening from inside/outside 32, 33,
90, 94, 100
Power closing assist for doors 110
Remote door unlock (Tele Aid) 248
Unlocking the driver’s door, Mechani-
cal key 372
DOT 309
Drink holder see Cup holder
Drinking and driving 259
Drive gear position, Automatic
transmission 48, 165, 167
Driving
Abroad 267
Hydroplaning 263
In winter 265
Instructions 45, 259
Problems 56
Safety systems 80
Systems 205
Through standing water 266
Tips, Automatic transmission 169

442 IndexL
Labels 406
Lamp sensor
Message in display 356
Lamps, exterior 125, 379
Messages in display 354
Replacing bulbs 379, 381, 382
Warning sounds 59, 126
Lamps, indicator and warning
ABS 25, 328
Anti-theft alarm systems 86
Battery (SmartKey with
KEYLESS-GO*) 98
Battery (SmartKey) 92
Brakes 25, 329
Distronic* 25, 210, 216
Engine diagnostics 330, 331
Engine malfunction 25, 330, 331
ESP
®
25, 332, 333
Fog lamps 125
Front passenger front air bag off 28,
67, 74, 336
Fuel reserve 25, 331High beam headlamp 25
Instrument cluster 328
Parking lamps 125
Parktronic*, Warning indicators 225
Seat belt telltale 25, 333
SRS 25, 63
Tire inflation pressure 25
Tow-away alarm 88
Turn signals 25
Lamps, interior 131
Language, Setting 158
LATCH-type child seat anchors see Chil-
dren in the vehicle
Lever for voice control system* 23
License plate lamp
Messages in display 355
Replacing bulbs 379, 383
Light alloy wheels, cleaning 324
Lighter see Cigarette lighter
Lighting, Exterior and interior 125
Limp Home Mode, Emergency operation of
automatic transmission 177
Line of fall 429Loading see Vehicle loading
Locator lighting 160
Locking knob 100, 429
Loss of
Mechanical key 94, 100
Service and Warranty Information
Booklet 405
SmartKey 94
SmartKey with KEYLESS-GO* 100
Low beam headlamps
Messages in display 356
Replacing bulbs 379
Switching on 52
Lubricants 418

444 Index
Hood 353
Instrument cluster 350
Lamp sensor 356
Lamps 354
License plate lamp 355
Low beam headlamps 356
Maintenance service indicator 315
Parking brake 345
Parking lamps 357
Power tilt/sliding sunroof 359
Reverse lamps 357
Seat belts 359
Selector lever 344
Side marker lamps 356
SmartKey 353
SmartKey with KEYLESS-GO* 353
Tail lamps 357
Tele Aid 359
Telephone* 360
Tires 361
Trunk 360
Turn signal lamps 358
Washer fluid 360
Multifunction steering wheel 138, 430
Button operation 138N
Navigation system
See separate COMAND operating in-
structions
Net, parcel 234
Neutral gear position, Automatic
transmission 48, 165, 167
New vehicle break-in 258
Night security illumination 160
Normal occupant weight 310
Number, vehicle identification (VIN) 406O
Occupant distribution 310
Occupant safety 62
Air bags 63
Children and air bags 64
Children in the vehicle 72
Fastening the seat belt 45
Front passenger front air bag off indica-
tor lamp 74
Infant and child restraint systems 72
LATCH-type child seat anchors 77
Seat belts 45, 66
Odometer 135
Oil see Engine oil
One-touch gearshifting 172
Operating safety 16
Ornamental moldings, cleaning 321
Outside temperature indicator 25, 136
Overdue maintenance service 316
Overhead control panel 29
Overspeed range, Engine 430