jump start MERCEDES-BENZ CL600 2007 C216 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: CL600, Model: MERCEDES-BENZ CL600 2007 C216Pages: 723
Page 12 of 723
Contents
Practical hints................................. 565
What to do if …?................................. 566
Lamps in instrument cluster ........ 566
Air bag off indicator lamp............. 578
Vehicle status messages
in the multifunction display .......... 580
Where will I find ...? ........................... 632
First aid kit ................................... 632
Vehicle jack, vehicle tool kit,
luggage bowl, Minispare wheel .... 632
Unlocking/locking in an emergency .. 635
Unlocking the vehicle ................... 635
Locking the vehicle ...................... 636
Mechanically releasing
the electronic parking brake ........ 637
Opening/closing in an emergency..... 638
Power tilt/sliding sunroof ............ 638
Replacing SmartKey batteries ........... 639
SmartKey/SmartKey
with KEYLESS-GO*....................... 639Replacing bulbs .................................. 641
Bulbs ............................................. 642
Replacing bulbs
for front lamps .............................. 644
Replacing bulbs
for the rear lamps ......................... 646
Replacing wiper blades....................... 647
Placing wiper arms
in vertical position ........................ 647
Removing wiper blades ................. 648
Installing wiper blades .................. 648
Flat tire ............................................... 649
Preparing the vehicle .................... 649
Mounting the Minispare wheel...... 649Batteries............................................. 655
Disconnecting starter battery ....... 657
Removing starter battery .............. 658
Charging battery ........................... 658
Reinstalling starter battery ........... 659
Reconnecting starter battery ........ 659
Jump starting...................................... 660
Towing the vehicle.............................. 663
Installing towing eye bolt .............. 666
Fuses.................................................. 667
Fuse boxes
in engine compartment................. 668
Fuse boxes
in passenger compartment ........... 669
Emergency engine shut-down ....... 670
Page 337 of 723
336 Controls in detail
Starter switch positions
SmartKey
Starter switch
0For removing SmartKey
1Power supply for some electrical con-
sumers, such as seat adjustment
2Ignition (power supply for all electrical
consumers) and driving position.
All lamps (except high beam headlamp
indicator lamp and turn signal indicator
lamps unless activated) in the instru-
ment cluster come on. If a lamp in the
instrument cluster fails to come on
when the ignition is switched on, have
it checked and replaced if necessary.
If a lamp in the instrument cluster re-
mains on after starting the engine or
comes on while driving, refer to “Lamps
in instrument cluster” (
page 566).
3Starting position
For information on starting the engine us-
ing the SmartKey, see “Starting with the
SmartKey” (
page 379).
Warning!G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.
iWhen you switch on the ignition, the indica-
tor and warning lamps (except high beam head-
lamp indicator lamp and turn signal indicator
lamps unless activated) in the instrument cluster
come on. The indicator and warning lamps (ex-
cept high beam headlamp indicator lamp and
turn signal indicator lamps if activated) should go
out when the engine is running. This indicates
that the respective systems are operational.
!If you turn off the engine using the
SmartKey and
remove the SmartKey from the starter
switch
or
open a door
the transmission will shift to park positionP
automatically.
Keep in mind that turning off the engine with the
SmartKey alone only will automatically shift the
transmission to neutral positionN.
!If the SmartKey cannot be turned in the
starter switch, the battery may not be sufficient-
ly charged.
Check the battery and charge it if necessary
(
page 655).
Get a jump start (page 660).
To prevent accelerated battery discharge or a
completely discharged battery, always remove
the SmartKey from the starter switch when the
engine is not in operation.
Page 382 of 723
381 Controls in detail
Driving and parking
The engine does not start. You cannot
hear the starter.
The battery may not be sufficiently
charged.
Get a jump start (page 660).
If the engine will not start despite a jump
start:
Call Roadside Assistance.
Contact an authorized Mercedes-Benz
Center or call Roadside Assistance.
Driving off
Depress the brake pedal.
The gear selector lever can now be
used.
Shift automatic transmission toD orR.
Release the brake pedal.
Carefully depress the accelerator
pedal.
The electronic parking brake is auto-
matically released (
page 384).
The red brake warning lamp 0
(USA only) or ! (Canada only) in the
instrument cluster goes out.After a cold start, the automatic transmis-
sion shifts at a higher engine revolution.
This allows the catalytic converter to reach
its operating temperature earlier.
iWait for the gear selection process to com-
plete before setting the vehicle in motion.
iShifting from gear position P to position R,
N, or D is only possible with the brake pedal de-
pressed. Without the brake pedal depressed, the
gear selector lever can be moved, but the park-
ing pawl remains engaged, not allowing shifting
to occur.
!If you hear a warning signal, the red indica-
tor lamp 0 (USA only) or ! (Canada only)
in the instrument cluster flashes and the mes-
sage “Please release parking brake” appears in
the multifunction display when driving off, you
are driving with the electronic parking brake en-
gaged, or you are carrying out an emergency
brake application with the electronic parking
brake.
Release the electronic parking brake
(
page 384).
iOnce the vehicle is in motion, the automatic
central locking system engages and the locking
knobs in the doors move down.
The automatic door lock feature can be deacti-
vated (
page 238).
You can open a locked door from the inside.
Open door only when conditions are safe to do
so.
Page 487 of 723
486 Controls in detail
Useful features
Roadside Assistance button•
Press and hold Roadside Assistance
button • (for longer than
2 seconds).
A call to a Mercedes-Benz Roadside As-
sistance dispatcher will be initiated.
The button will flash while the call is in
progress. The message:
“Connecting call” appears in the
multifunction display
“Roadside Assistance Activated”
appears in the COMAND display
and the audio system is muted.
When the connection is established, the
message:
“Call connected” appears in the multi-
function display
“Roadside Assistance Activated”
appears in the COMAND display The Tele Aid system will transmit data gen-
erating the vehicle identification number,
model, color and location (subject to avail-
ability of cellular and GPS signals).
A voice connection between the Roadside
Assistance dispatcher and the occupants
of the vehicle will be established.
Describe the nature of the need for as-
sistance.
The Mercedes-Benz Roadside Assistance
dispatcher will either dispatch a qualified
Mercedes-Benz technician or arrange to
tow your vehicle to the nearest authorized
Mercedes-Benz Center. For services such
as labor and/or towing, charges may ap-
ply. Refer to the Roadside Assistance Man-
ual for more information.
These programs are only available in the
USA:
Sign and Drive services: Services such
as jump start, a few gallons of fuel or
the replacement of a flat tire with the
vehicle spare tire are obtainable.
iThe indicator lamp in the Roadside Assis-
tance button• remains illuminated in red for
approximately 10 seconds during the system
self-check after switching on the ignition (togeth-
er with the SOS button and the Information
button¡).
See system self-check (
page 483) if the indi-
cator lamp does not come on in red or stays on
longer than approximately 10 seconds.
If the indicator lamp in the Roadside Assistance
button• is flashing continuously and no
voice connection to the Response Center was
established, the Tele Aid system could not ini-
tiate a Roadside Assistance call (e.g. the relevant
mobile phone network is not available). The mes-
sage:
“Call failed” appears in the multifunction dis-
play for approximately 10 seconds
“Call could not be connected!” appears in
the COMAND display. Confirm the message
pressing
n (page 84).
Roadside Assistance calls can be terminated us-
ing button t on the multifunction steering
wheel or COMAND (
page 120).
Page 568 of 723
565 Practical hints
What to do if …?
Where will I find ...?
Unlocking/locking in an emergency
Opening/closing in an emergency
Replacing SmartKey batteries
Replacing bulbs
Replacing wiper blades
Flat tire
Batteries
Jump starting
Towing the vehicle
Fuses
Page 663 of 723
660 Practical hints
Jump starting
If the starter battery is discharged, the en-
gine can be started with jumper cables and
the battery of another vehicle. Observe the
following:
Jump starting should only be performed
when the engine and catalytic convert-
er are cold.
Do not start the engine if the battery is
frozen. Let the battery thaw out first.
Only use 12-volt battery to jump start
your vehicle. Jump starting with a high-
er voltage battery could damage the ve-
hicle’s electrical system, which will not
be covered by the Mercedes-Benz Lim-
ited Warranty.
Only use jumper cables with sufficient
cross-section and insulated terminal
clamps.
Always make sure that the jumper ca-
bles are not on or near pulleys, fans or
other parts that move when an engine
is started or running.
Warning!G
Failure to follow these directions will cause
damage to the electronic components, and
can lead to a battery explosion and severe
injury or death.
Never lean over batteries while connecting
or jump starting, you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water, and seek
medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and very explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
Attempting to jump start a frozen battery
can result in it exploding, causing personal
injury.
Read all instructions before proceeding.
!Do not tow-start the vehicle.
!Jump starting should only be performed on
the starter battery installed in the engine com-
partment.
Avoid repeated and lengthy starting attempts.
Do not attempt to start the engine using a bat-
tery quick charge unit.
If engine does not run after several unsuccessful
starting attempts, have it checked at the nearest
authorized Mercedes-Benz Center.
Excessive unburned fuel generated by repeated
failed starting attempts may damage the catalyt-
ic converter and may present a fire risk.
Make sure the jumper cables do not have loose
or missing insulation.
Make sure the cable clamps do not touch any
other metal part while the other end is still at-
tached to a battery.
Page 664 of 723
661 Practical hints
Jump starting
Jump starting should only be performed on
the starter battery. The starter battery is
located in the engine compartment on the
passenger side (
page 657).
Make sure the two vehicles do not
touch.
Secure vehicle in place with electronic
parking brake (
page 384).
Shift the automatic transmission toP
(
page 389).
Turn off all electrical consumers, ex-
cept hazard warning flashers or work
lights.
Open the hood (page 512).
Start the engine of the vehicle with the
charged battery and run at idle speed.1Negative clamp
2Negative terminal of charged battery
3Positive terminal of charged battery
4Positive terminal of discharged battery
Warning!G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(
page 655).
iVehicles with KEYLESS-GO: remove the
KEYLESS-GO button (
page 337) and use the
SmartKey with KEYLESS-GO like a normal
SmartKey.
Page 665 of 723
662 Practical hints
Jump starting
Remove red cover from positive
terminal4.
Connect positive terminal3 of the
charged battery with positive
terminal4 of the discharged battery
with the jumper cable. Clamp cable to
charged battery3 first.
Connect negative terminal2 of
charged battery to jumper cables and
attach other end of the jumper cable
with the negative clamp1 to a suit-
able ground point on the vehicle.
Get into vehicle and start engine within
30 seconds.
If the starting attempt does not suc-
ceed:
Turn the SmartKey in starter switch
to position 0.
Take out the SmartKey.
Turn off engine of donor vehicle, re-
start it and let it run at idle speed
for several minutes.
Disconnect the jumper cable during
this time.
Reconnect jumper cable as de-
scribed before.
Restart engine.
While the engine is running, switch off
several electrical consumers such as
the blower.
Disconnect jumper cables first nega-
tive clamp1 from ground point and
negative terminal2, then from posi-
tive terminals4 and3.
Have the battery checked at the near-
est authorized Mercedes-Benz Center.!Never invert the terminal connections.
Page 667 of 723
664 Practical hints
Towing the vehicle
Warning!G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the
vehicle. Adapt your driving accordingly.
!When towing the vehicle with all wheels on
the ground or with the front axle raised, the start-
er battery must be connected and charged. Oth-
erwise:
you will not be able to switch on the ignition
you will not be able to engage the automatic
transmission in positionN (
page 394)
you cannot release the electronic parking
brake
For information on charging the starter battery
see “Batteries” (
page 655) or see “Jump start-
ing” (
page 660).
!Make sure that the electronic parking brake
is released. If the electronic parking brake is
malfunctioning, release it mechanically
(
page 637).
!If the vehicle is towed with the front axle
raised, the automatic transmission must be in
positionN and the engine must be shut off
(SmartKey or SmartKey with KEYLESS-GO* in
starter switch position0 or1). Active braking
action through the ESP
® may otherwise
seriously damage the brake system.
!When towing the vehicle with all wheels on
the ground, the automatic transmission must be
shifted to positionN and the SmartKey or
SmartKey with KEYLESS-GO* must be in starter
switch position2.
When towing the vehicle with all wheels on the
ground or the front axle raised, the vehicle may
be towed only for distances up to 30 miles
(50 km) and at a speed not to exceed 30 mph
(50 km/h).
!If the vehicle is towed with all wheels on the
ground or with the front axle raised, the trans-
mission must be in positionN.
If you turn off the engine using
the SmartKey and
remove the SmartKey from the starter
switch
or
open a door
the KEYLESS-GO* start/stop button and
open a door
the transmission will shift to park position P
automatically.
Page 698 of 723
695 Index
B
Backup lamps
Replacing bulbs 642
Bar 545
BAS 66
Batteries, SmartKey
Checking battery condition 332
Replacing 639
Batteries, SmartKey with KEYLESS-GO*
Checking battery condition 332
Replacing 639
Batteries, vehicle 655
Charging 658
Discharged, Jump starting 660
Disconnecting 657
For electrical consumers 655
For starter 655
Message in display 608
Reconnecting 659
Removing 658
Bead 545
Beverage holder see Cup holder
Bluetooth
®
Settings (COMAND) 232
Brake assist system (BAS Plus) 67
Brake assist system (BAS) 66Brake fluid 511, 685, 687
Brake lamp bulbs 642
Brake lamp, high mounted 642
Brake pads
Message in display 598
Brake warning lamp 31
Brakes 500
Warning lamp 31, 567
Break-in period 498
Bulbs, replacing 641
Additional turn signals 642
Brake lamps 642
Fog lamps 642
Front lamps 642
High beam 642
High mounted brake lamp 642
License plate lamps 642
Low beam 642
Parking and standing lamps 642
Rear fog lamp 642
Turn signal lamps 642C
California retail buyers and lessees,
important notice for 15
Can holder see Cup holder
Capacities and
recommended fuel/lubricants 684
Carpets, Cleaning and care of 564
Catalytic converter 507
CD
Ejecting (COMAND) 113
Loading (COMAND) 111
Menu overview (COMAND) 114
Playback options (COMAND) 119
Selecting a medium (COMAND) 117
Selecting a track (COMAND) 117
CD (COMAND) 107
Central locking
Automatic 334
Locking/unlocking from inside 335
Central locking/unlocking switches 335
Certification label 674
Change of address or ownership 16