jump start MERCEDES-BENZ CLK550 2008 C209 Owner's Manual

Contents
Resetting activated head restraints ... 440
Resetting
activated head restraints.............. 440
Replacing SmartKey batteries ............ 441
SmartKey / SmartKey
with KEYLESS-GO* ....................... 442
Replacing bulbs ................................. 443
Bulbs ............................................ 444
Replacing bulbs for front lamps.... 446
Replacing bulbs for rear lamps ..... 448
Replacing wiper blades ...................... 450
Removing and installing
wiper blades ................................. 450
Flat tire .............................................. 452
Preparing the vehicle.................... 452
Sealing tires with TIREFIT
(CLK 63 AMG only) ....................... 452
Mounting the Minispare wheel ..... 458
MOExtended system*................... 463
Battery ............................................... 464
Disconnecting the battery ............ 465
Removing the battery ................... 465
Charging and
reinstalling the battery ................. 466
Reconnecting the battery ............. 466
Jump starting ..................................... 467Towing the vehicle ............................. 469
Towing the vehicle ....................... 469
Installing towing eye bolt ............. 470
Fuses ................................................. 472
Fuse box
in passenger compartment .......... 472
Fuse box
in engine compartment ................ 473
Fuse box
in trunk ........................................ 474
Technical data................................. 475
Parts service ...................................... 476
Warranty coverage............................. 477
Loss of Service and Warranty
Information Booklet ..................... 477
Identification labels ........................... 478
Layout of poly-V-belt drive ................. 480
CLK 350 / CLK 550 ..................... 480
CLK 63 AMG ................................ 480
Engine................................................ 481
Rims and tires.................................... 482
Same size tires ............................. 483
Mixed size tires ............................ 484
Minispare wheel ........................... 486Electrical system ............................... 487
Main dimensions and weights ........... 488
Main dimensions .......................... 488
Weights ........................................ 488
Fuels, coolants, lubricants, etc. ......... 489
Capacities .................................... 489
Engine oils ................................... 491
Engine oil additives ...................... 491
Air conditioning refrigerant .......... 491
Brake fluid.................................... 491
Premium unleaded gasoline ......... 492
Fuel requirements ........................ 492
Gasoline additives ........................ 493
Coolants ...................................... 494
Windshield washer system
and headlamp cleaning system* .. 496
Index................................................. 497

39 Getting started
Unlocking
For more information, see “SmartKey”
(
page 100).
For information on starting the engine us-
ing the SmartKey, see “Starting with the
SmartKey” (
page 52).SmartKey with KEYLESS-GO*
Pressing the KEYLESS-GO start/stop but-
ton on the gear selector lever corresponds
to turning the SmartKey to the various
starter positions.
If you firmly depress the brake pedal dur-
ing pressing the KEYLESS-GO start/stop
button, the engine starts automatically.
You can also use the SmartKey with
KEYLESS-GO like a normal SmartKey.
KEYLESS-GO start/stop button
1USA only
2Canada only
The SmartKey with KEYLESS-GO must be
located in the vehicle.
Make sure the gear selector lever is set
toP.
Do not depress the brake pedal.
!If the SmartKey cannot be turned in the
starter switch, the battery may not be sufficient-
ly charged.

Check the battery and charge it if necessary
(
page 464).

Get a jump start (page 467).
To prevent accelerated battery discharge or a
completely discharged battery, always remove
the SmartKey from the starter switch when the
engine is not in operation.
iThe function of the SmartKey overrules the
KEYLESS-GO function.

53 Getting started
Driving
Starting difficulties
If the SmartKey is left in starter switch
position0 for an extended period of time,
it can no longer be turned in the switch. In
this case, the steering is locked.
To unlock, remove SmartKey from
starter switch and reinsert.
If the engine does not start as described,
carry out the following steps:
If you are starting the engine with the
SmartKey, turn SmartKey in starter
switch to position0 and repeat starting
procedure.
If you are starting the engine with
KEYLESS-GO*: Close any doors that
may be open to allow for better detec-
tion of the SmartKey with
KEYLESS-GO*.
Or:
Start the engine with the SmartKey as
radio signals from another source may
be interfering with the SmartKey with
KEYLESS-GO*.
Repeat the starting procedure
(
page 51).
Remember that extended starting at-
tempts can drain the battery.
Get a jump start (page 467).
If the engine does not start after several
starting attempts, there could be a mal-
function in the engine electronics or in the
fuel supply system.
Contact an authorized Mercedes-Benz
Center or call Roadside Assistance.
Parking brake
1Release handle
2Parking brake pedal
Warning!G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. Children could release the
parking brake, which could result in an acci-
dent and/or serious personal injury.


298 Controls in detail
Useful features
Roadside Assistance button•
The Roadside Assistance button• is
located below the center armrest cover.
Press and hold the •button (for
longer than 2 seconds).
A call to a Mercedes-Benz Roadside
Assistance dispatcher will be initiated.
The •button will flash while the call
is in progress. The message
Connecting Call will appear in the
multifunction display and the audio
system is muted.
When the connection is established, the
message
Call Connected appears in the
multifunction display. The Tele Aid system
will transmit data generating the vehicle
identification number, model, color and lo-
cation (subject to availability of cellular
and GPS signals).
A voice connection between the Roadside
Assistance dispatcher and the occupants
of the vehicle will be established.
Describe the nature of the need for as-
sistance.The Mercedes-Benz Roadside Assistance
dispatcher will either dispatch a qualified
Mercedes-Benz technician or arrange to
tow your vehicle to the nearest authorized
Mercedes-Benz Center. For services such
as labor and/or towing, charges may
apply. Refer to the Roadside Assistance
manual for more information.
The following is only available in the USA:

Sign and Drive services: Services such
as jump start, a few gallons of fuel or
the replacement of a flat tire with the
vehicle spare tire are obtainable.
iThe indicator lamp on the Roadside
Assistance button• remains illuminated in
red for approximately 10 seconds during the sys-
tem self-check after switching on the ignition (to-
gether with the SOS button and the Information
button¡).See system self-check (
page 295) when the
indicator lamp does not come on in red or stays
on longer than approximately 10 seconds.
If the indicator lamp on the Roadside Assistance
button• is flashing continuously and there
was no voice connection to the Response Center
established, then the Tele Aid system could not
initiate a Roadside Assistance call (e.g. the rele-
vant cellular phone network is not available). The
message
Call Failed appears in the multi-
function display.
Roadside Assistance calls can be terminated us-
ing the tbutton on the multifunction steer-
ing wheel or the respective button for ending a
telephone call on the audio system or the
COMAND* head unit.

377 Practical hints
What to do if …?
Where will I find...?
Unlocking/locking in an emergency
Opening/closing in an emergency
(Cabriolet)
Resetting activated head restraints
Replacing SmartKey batteries
Replacing bulbs
Replacing wiper blades
Flat tire
Battery
Jump starting
Towing the vehicle
Fuses

464 Practical hints
Battery
The battery is located in the engine
compartment on the right hand side.
1Clamps
Removing filter box:
Release clamps1.
Remove filter box.
Installing filter box:
Insert filter box properly.
Secure it with clamps1.
Warning!G
Failure to follow these instructions can re-
sult in severe injury or death.
Observe all safety instructions and
precautions when handling automotive
batteries (
page 329).
Never lean over batteries while connecting,
you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water and seek
medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
!Never loosen or detach battery terminal
clamps while the engine is running or the
SmartKey is in the starter switch. Otherwise the
alternator and other electronic components
could be severely damaged.
Have the battery checked regularly at an autho-
rized Mercedes-Benz Center.
Refer to Maintenance Booklet for maintenance
intervals or contact an authorized
Mercedes-Benz Center for further information.
Warning!G
Do not place metal objects on the battery as
this could result in a short circuit.
Use leak-proof battery only to avoid the risk
of acid burns in the event of an accident.

467 Practical hints
Jump starting
Jump starting
If the battery is discharged, the engine can
be started with jumper cables and the
battery of another vehicle. Observe the
following:

Jump starting should only be performed
when the engine and catalytic convert-
er are cold.

Do not start the engine if the battery is
frozen. Let the battery thaw out first.

Only jump start from batteries with the
same voltage rating (12 V). Jump start-
ing with a higher voltage battery could
damage the vehicle’s electrical system,
which will not be covered by the
Mercedes-Benz Limited Warranty.

Only use jumper cables with sufficient
cross-section and insulated terminal
clamps.

Always make sure the jumper cables
are not on or near pulleys, fans or other
parts that move when an engine is
started or running.
Warning!G
Failure to follow these directions will cause
damage to the electronic components, and
can lead to a battery explosion and severe
injury or death.
Never lean over batteries while connecting
or jump starting, you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water, and seek
medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and very explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
Attempting to jump start a frozen battery
can result in it exploding, causing personal
injury.
Read all instructions before proceeding.
!Do not tow-start the vehicle.
!Avoid repeated and lengthy starting
attempts.
Do not attempt to start the engine using a bat-
tery quick charge unit.
If the engine does not run after several unsuc-
cessful starting attempts, have it checked at the
nearest authorized Mercedes-Benz Center.
Excessive unburned fuel generated by repeated
failed starting attempts may damage the catalyt-
ic converter and may present a fire risk.
Make sure the jumper cables do not have loose
or missing insulation.
Make sure the cable clamps do not touch any
other metal part while the other end is still
attached to a battery.
Warning!G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(
page 329).

468 Practical hints
Jump starting
The battery is located on the right side of
the engine compartment. For jump start-
ing, use the terminals in front of the
battery.
Make sure the two vehicles do not
touch.
Turn off all electrical consumers.
Apply the parking brake (page 59).
Make sure the gear selector lever is set
to positionP (
page 174).
Open the hood (page 323).
Flip up cover from positive under hood
terminal2 in front of the filter box
(
page 465).1Positive terminal of charged battery
2Positive under hood terminal in front of
discharged battery
3Negative under hood terminal in front
of discharged battery
4Negative terminal of charged battery
Connect the positive terminal1 of the
charged battery with the positive under
hood terminal 2 in front of the filter
box with the jumper cable. Clamp cable
to charged battery1 first.
Start engine of the vehicle with the
charged battery and run at idle speed.
Connect the negative terminal4 of
the charged battery with the negative
under hood terminal 3 in front of the
filter box with the second jumper cable.
Clamp the cable to the negative
terminal4 of the charged battery
first.
Start the engine of the disabled
vehicle.
You can now turn on the electrical con-
sumers. Do not switch on the headlamps
under any circumstances.
Remove the jumper cables first from
the negative terminals3 and4 and
then from the positive terminals2
and1.
You can now switch on the headlamps.
Have the battery checked at the near-
est authorized Mercedes-Benz Center.
!Never invert the terminal connections.

470 Practical hints
Towing the vehicle
Installing towing eye bolt
Towing eye bolt CLK 350
1Cover on right side of front bumper2Cover on right side of rear bumper
To remove cover:
Press mark on cover 1 or 2.
Lift cover off to reveal the threaded
hole for towing eye bolt.
The towing eye bolt is supplied with the
tool kit (located in the compartment under-
neath the trunk floor).
Screw towing eye bolt in to its stop and
tighten with wheel wrench.
To reinstall cover:
Fit cover 1 or 2 and snap into place.
!Towing of the vehicle should only be done
using the properly installed towing eye bolt.
Never attach tow cable, tow rope or tow rod to
the vehicle chassis, frame or suspension parts.
iWhen towing the vehicle with all wheels on
the ground, please note the following:
With the automatic central locking activated and
the SmartKey in starter switch position2, or
KEYLESS-GO* start/stop button in position2,
the vehicle doors lock if the left front wheel as
well as the right rear wheel are turning at vehicle
speeds of approximately 9 mph (15 km / h) or
more.
To prevent the vehicle door locks from locking,
deactivate the automatic central locking
(
page 166).
iTo signal turns while being towed with the
hazard warning flasher in use, switch on the
ignition and activate the combination switch for
the left or right turn signal in the usual manner –
only the selected turn signal will operate.
Upon canceling the turn signal, the hazard
warning flasher will operate again.
iIf the battery is disconnected or discharged

the SmartKey will not turn in the starter
switch. For more information, see “Battery”
(
page 464) and “Jump starting”
(
page 467).

the gear selector lever will remain locked in
positionP. For information on manually un-
locking the transmission gear selector lever,
see (
page 429).

498 Index
Automatic lighting control,
Interior lighting 136
Automatic locking when driving 118
Automatic shift program 178
Automatic transmission
Accelerator position 176
Automatic shift program 178
Emergency operation
(limp-home mode) 184
Gear ranges 177
Gear selector lever 51, 172
Gear selector lever control
one-touch gearshifting 179
Gear selector lever positions 174
Gear shifting malfunctions 184
Kickdown 176
Kickdown, manual shift program 184
Manual shift program
CLK 63 AMG 182
Program mode selector switch 178
Shifting procedure 173
Starting engine 51
Steering wheel gearshift control
one-touch gearshifting* 180
Transmission fluid level 327
Automatic Transmission Fluid see ATFB
Backrest 281
Seat, Multicontour* 124
Seat, Power 42
Backup lamps
Messages in display 414
Replacing bulbs 443, 444
Bar 358
BAS 92
Batteries, SmartKey
Changing 442
Checking battery condition 108
Battery, Vehicle 329, 464
Charging 466
Connecting 466
Disconnecting 465
Installing 466
Jump starting 467
Messages in display 403
Removing 465
Bead 358
Beverage holder see Cup holder
Block heater (Canada only) 363
Bolts, Spare wheel 426Brake fluid 491
Checking 322
Message in display 404
Brake lamp
Cleaning lenses 372
High mounted 444
Replacing bulbs 444, 448
Brake pads
Message in display 404
Brakes 310
High-performance brake system
(CLK 63 AMG only) 311
Warning lamp 380
Break-in period 308
Bulbs, replacing see Replacing bulbs