key MERCEDES-BENZ CLS 2014 Owners Manual

XPark the vehicle onalevel surface.
Only check the coolant level when the
vehicle is onalevel surface and the engine
has cooled down.
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
On vehicles with KEYLESS-GO, press the
Start/Stop button twice (Ypage 147).
XCheck the coolant temperature display in
the instrument cluster.
The coolant temperature must be below
158‡(70 †).
XTurn the SmartKey to position
0(Ypage 147) in the ignition lock.
XSlowly turn caphalfaturn counter-
clockwise to allow excess pressure to
escape.
XTurn capfurther counter-clockwise and
remove it.
If the coolant is at the level of marker bar
$in the filler neck when cold, there is
enough coolant in coolant expansion
tank.
If the coolant level is approximately 0.6 in
(1.5 cm) above marker bar$in the fuel
filler neck when warm, there is enough
coolant in expansion tank.
XIf necessary, add coolant that has been
tested and approved by Mercedes-Benz.
XReplace capand turn it clockwise as far
as it will go.
For further information on coolant,see
(Ypage 377).
Adding washer fluid to the windshield
washer system/headlampcleaning
system
GWARNING
Windshield washer concentrate is highly
flammable. If it comes intocontactwith hot
enginecomponentsorthe exhaust systemit
could ignite. There isariskoffire and injury.
Make sure that no windshield washer
concentrate is spilled nexttothe filler neck.
XTo open:pull capupwards by the tab.
XAdd the premixed washer fluid.
XTo close:press capontothe filler neck
until it engages.
The washer fluid reservoir is used for both the
windshield washer system and the headlamp
cleaning system.
If the washer fluid level drops below the
recommended minimum of1liter,amessage
appears in the multifunction display
promptingyou to refill the washer fluid
(Ypage 262).
Further information on windshield washer
fluid/antifreeze (Ypage 378).
Maintenance
ASSYST PLUS
Service messages
The ASSYSTPLUS service interval display
informsyou of the nextservice due date.
Maintenance309
Maintenance and care
Z

Under these or similarconditions, have, for
example, the air filter, engine oil and oil filter
replaced or changed more frequently. Under
arduous operating conditions, the tires must
be checked more often.Further information
can be obtained ataqualified specialist
workshop, e.g. an authorized Mercedes-Benz
Center.
Driving abroad
An extensive Mercedes-Benz Servicenetwork
is also available in other countries. You can
obtain further information from any
authorized Mercedes-Benz Center.
Care
General notes
HEnvironmental note
Dispose of empty packagingand cleaning
clothsinanenvironmentally responsible
manner.
!For cleaningyour vehicle, do not use any
of the following:
Rdry, rough or hard cloths
Rabrasive cleaningagents
Rsolvents
Rcleaningagents containingsolvents
Do not scrub.
Do not touch the surfaces or protective
films with hard objects, e.g.aring or ice
scraper. You could otherwise scratch or
damage the surfaces and protective film.
!Do not park the vehicle for an extended
period straight after cleaningit, particularly
after having cleaned the wheels with wheel
cleaner. Wheel cleaners could cause
increased corrosion of the brake discs and
brake pads/linings. For this reason, you
should drive forafew minutes after
cleaning. Braking heats the brake discs and
the brake pads/linings, thus drying them.
The vehicle can then be parked.
Regular care of your vehicle isacondition for
retaining the quality in the long term.
Use care productsand cleaningagents
recommended and approved by Mercedes-
Benz.
Washing the vehicle and cleaning the
paintwork
Automatic car wash
GWARNING
Braking efficiency is reduced after washing
the vehicle. There isarisk of an accident.
After the vehicle has been washed, brake
carefully while paying attention to the traffic
conditions until full brakingpower is restored.
!If DISTRONIC PLUS or the HOLD function
is activated, the vehicle brakes
automatically in certain situations. To
preventdamage to thevehicle,deactivate
DISTRONICPLUS and the HOLD function in
the following or other similar situations:
Rwhen towing the vehicle
Rin the car wash
!Never clean yourvehicle inaTouchless
Automatic Car Wash as these use special
cleaningagents.These cleaning agents can
damage the paintwork or plastic parts.
!Make sure that:
Rthe side windows and the sliding sunroof
are fully closed.
Rthe ventilation/heating is switched off
(the OFF button has been pressed).
Rthe windshield wiper switch is in position
0.
Otherwise, the vehicle might be damaged.
!In car washes withatowing mechanism,
make sure that the automatic transmission
is in transmission positionN,otherwise the
vehicle could be damaged.
RVehicles withaSmartKey:
Care311
Maintenance and care
Z

Do not remove the SmartKeyfromthe
ignition lock. Do not open the driver's
door or front-passengerdoor when the
engine is switched off. Otherwise, the
automatic transmission selects park
positionPautomatically and locks the
wheels. You can prevent this by shifting
the automatic transmission toN
beforehand.
RVehicles with KEYLESS-GO:
Do not open the driver's door or front-
passenger door when the engine is
switched off. Otherwise, the automatic
transmission selects park positionP
automatically and locks the wheels.
Observe the following to make sure that the
automatic transmission stays in positionN:
XMake sure the vehicle is stationary and the
ignition is switched off.
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
Use the SmartKey instead of the Start/
Stop button on vehicles with KEYLESS-GO.
XDepress and hold the brake pedal.
XShift the automatic transmission to
positionN.
XRelease the brake pedal.
XRelease the electric parking brake.
XSwitch off the ignition and leave the
SmartKey in the ignition lock.
You can wash the vehicle in an automatic car
wash from the very start.
If the vehicle is very dirty, pre-wash it before
cleaning it in an automatic car wash.
After using an automatic car wash, wipe off
wax from the windshield and the wiper
blades. This will prevent smears and reduce
wiping noises caused by residue on the
windshield.
Washing by hand
In some countries, washing by hand is only
allowedatspecially equipped washing bays.
Observe the legal requirements in all
countries concerned.
XDo not use hot water and do not wash the
vehicle in direct sunlight.
XUseasoft sponge to clean.
XUseamild cleaning agent, such asacar
shampoo approved by Mercedes-Benz.
XThoroughly hose down the vehicle with a
gentle jet of water.
XDo not point the water jet directly towards
the air inlet.
XUse plenty of water and rinse out the
sponge frequently.
XRinse the vehicle with clean water and dry
thoroughly withachamois.
XDo not let the cleaning agent dry on the
paintwork.
When using the vehicle in winter, remove all
traces of road salt deposits carefully and as
soon as possible.
Power washers
GWARNING
The water jet fromacircular jet nozzle (dirt
blasters) can cause invisible exterior damage
to the tires or chassis components.
Componentsdamaged in this way may fail
unexpectedly. There isarisk of an accident.
Do not use power washers with circular jet
nozzles to clean the vehicle. Have damaged
tires or chassis components replaced
immediately.
!Always maintainadistance of at least
11.8in(30 cm) between the vehicleand the
powerwasher nozzle. Information about
thecorrectdistanceisavailablefromthe
equipmentmanufacturer.
Movethepower washernozzle around
when cleaning your vehicle.
Do not aim directly at any of the following:
Rtires
Rdoor gaps, roof gaps, joints, etc.
Relectrical components
312Care
Maintenance and care

Alignment bolt
%Sheet for faulty wheel
Tire inflation compressor
Lugwrench
Fuseallocation chart
XOpenthe trunk lid.
XLift the trunk floor upwards (Ypage 283).
Flat tire
Preparing the vehicle
Your vehicle may be equipped with:
RMOExtended tires (tires with run-flat
properties) (Ypage 321)
Vehicle preparation is not necessary on
vehicles with MOExtended tires.
Ran emergency spare wheel(Ypage 367)
Information on changing/mountingawheel
(Ypage 357).
XStop the vehicle on solid, non-slippery and
level ground, as far away as possible from
traffic.
XSwitch on the hazard warning lamps.
XSecure the vehicle against rolling away
(Ypage 167).
XIf possible, bring the front wheels into the
straight-ahead position.
XVehicles with AIRMATIC: make sure that
"normal" level is selected (Ypage 189).
XSwitch off the engine.
XVehicles without KEYLESS-GO:remove
the SmartKey from the ignition lock.
XVehicles with KEYLESS-GO:open the
driver's door.
The on-board electronicsnow have status
0.This is the same as the SmartKey having
been removed.
XVehicles with KEYLESS-GO:remove the
Start/Stop button from the ignition lock
(Ypage 147).
XAll occupants must get out of the vehicle.
Make sure that they are not endangered as
they do so.
XMake sure that no one is near the danger
area whileawheel is being changed.
Anyone who is not directly assisting in the
wheel change should, for example, stand
behind the barrier.
XGet out of the vehicle. Pay attention to
traffic conditionswhen doing so.
XClose the driver's door.
MOExtended tires (tires with run-flat
properties)
General notes
With MOExtended tires (tires with run flat
characteristics), you can continue to drive
your vehicle even if there isatotal loss of
pressure in one or more tires. The affected
tire must not show any clearly visible damage.
You can recognizeMOExtended tires by the
MOExtended marking which appears on the
sidewall of the tire. You will find this marking
next to the tire size designation, the load-
bearing capacity and the speed index
(Ypage 351).
MOExtended tires may only be used in
conjunction with an active tire pressure loss
warning system or with an active tire pressure
monitor.
If the pressureloss warning message
appearsinthe multifunction display:
RObserve the instructions in the display
messages (Ypage 258).
RCheck the tire for damage.
RIf driving on, observe the following notes.
The maximum driving distance is
approximately 50 miles (80 km) when the
vehicle is partially laden and approximately
18 miles (30 km) when the vehicle is fully
laden.
Flat tire321
Breakdown assistance

Beforehandling the battery,touch the vehicle
bodytoremove any existing electrostatic
build-up.
The highly flammable gasmixture forms when
charging the battery as well as whenjump-
starting.
Always makesure that neither you northe
battery is electrostatically charged.Abuild-
up of electrostaticcharge can be caused, for
example:
Rby wearing clothing made from synthetic
fibers
Rdue to friction between clothing and seats
Rif you push or pull the battery across the
carpet or other synthetic materials
Rif you wipe the battery withacloth
GWARNING
During the charging process,abattery
produces hydrogen gas. Ifashort circuit
occurs or sparks are created, the hydrogen
gas can ignite. There isarisk of an explosion.
RMake sure that the positive terminal of a
connected battery does not come into
contact with vehicle parts.
RNever place metal objectsortools on a
battery.
RIt is important that you observe the
described order of the battery terminals
when connecting and disconnecting a
battery.
RWhen jump-starting, make sure that the
battery poles with identical polarity are
connected.
RIt is particularly important to observe the
described order when connecting and
disconnecting the jumper cables.
RNever connect or disconnectthe battery
terminals while the engine is running.
GWARNING
Batteryacid is caustic. There isarisk of injury.
Avoid contact with the skin, eyes or clothing.
Do not inhale any battery gases. Do not lean
over the battery. Keep children away from
batteries. Wash battery acid immediately with
water and seek medical attention.
HEnvironmental note
Batteries contain dangerous
substances. It is against the
law to dispose of them with
the household rubbish. They
must be collected separately
and recycled to protect the
environment.
Dispose of batteries in an
environmentally friendly
manner. Take discharged
batteries toaqualified
specialist workshop or a
special collection point for
used batteries.
!Have the battery checked regularly at a
qualified specialist workshop.
Observe the service intervals in the
MaintenanceBooklet or contactaqualified
specialist workshop for more information.
!You should have all work involving the
battery carried out ataqualified specialist
workshop. In theexceptional casethatitis
necessaryfor you to disconnect thebattery
yourself, makesure that:
Ryou switch off theengineand remove the
SmartKey. On vehicles withKEYLESS-
GO, ensure that theignition is switched
off.Check that all the indicator lamps in
the instrumentcluster are off.Otherwise,
electroniccomponents, such as the
alternator,may be damaged.
Ryou first remove the negative terminal
clamp and then the positive terminal
clamp. Never swap the terminal clamps.
Otherwise, the vehicle's electronic
system may be damaged.
Rthe transmission is locked in positionP
after disconnectingthe battery. The
vehicle is secured against rolling away.
You can then no longer move the vehicle.
Battery (vehicle)323
Breakdown assistance
Z

The battery and the cover of the positive
terminal clamp must be installed securely
during operation.
Comply with safety precautions and take
protective measures when handling
batteries.
Risk of explosion.
Fire, open flames and smokingare
prohibited when handling the
battery. Avoid creatingsparks.
Battery acid is caustic. Avoid
contact with skin, eyes or clothing.
Wear suitable protective clothing,
especially gloves, apron and
faceguard.
Rinse any acid spills immediately
with clear water. Contact a
physician if necessary.
Wear eye protection.
Keep children away.
Observe this Operator's Manual.
For safety reasons, Mercedes-Benz
recommends that you only use batteries
which have been tested and approved for
your vehicle by Mercedes-Benz.These
batteries provide increased impact
protection to prevent vehicle occupants from
suffering acid burns should the battery be
damaged in the event of an accident.
In order for the battery to achieve the
maximum possible service life, it must always
be sufficiently charged.
The vehicle battery, like other batteries, can
discharge over time if you do not use the
vehicle. In this case, have the battery
disconnected ataqualified specialist
workshop. You can also charge the battery
withacharger recommended by Mercedes-
Benz.Contactaqualified specialist workshop
for further information.
Have the battery condition of charge checked
more frequently if you use the vehicle mainly
for short trips or if you leave it standingidle
foralengthy period. Consultaqualified
specialist workshop if you wish to leave your
vehicle parked foralong period of time.
iRemove the SmartKey if you park the
vehicle and do not require any electrical
consumers. The vehicle will then use very
little energy, thus conserving battery
power.
iIf the power supply has been interrupted,
e.g. if you reconnect the battery, you will
have to:
Rset the clock.Information on setting the
clock can be found in the separate
operating instructions.
On vehicles with COMAND and a
navigation system, the clock is set
automatically.
Rreset the function for folding the exterior
mirrors in/out automatically, by folding
the mirrors out once (Ypage 110).
Charging the battery
GWARNING
During charging and jump-starting, explosive
gases can escape from the battery. There is a
risk of an explosion.
Particularly avoid fire, open flames, creating
sparks and smoking. Ensure there is sufficient
ventilation while charging and jump-starting.
Do not lean overabattery.
GWARNING
Battery acid is caustic. There isarisk of injury.
Avoid contact with the skin, eyes or clothing.
Do not inhale any battery gases. Do not lean
324Battery (vehicle)
Breakdown assistance

XFirst, remove the jumper cablesfrom earth pointand negative terminal!,then from
positiveclampand positiveterminal$.Begineachtime at the contacts on your own
vehicle first.
XClose coverof positiveclampafterremoving the jumper cables.
XHave the battery checkedataqualified specialist workshop.
iJump-startingisnot considered to beanormal operatingcondition.
iJumper cables and further information regardingjump-starting can be obtained at any
qualified specialist workshop.
Towing and tow-starting
Importantsafetynotes
GWARNING
Functionsrelevant to safety are restricted or
no longer available if:
Rthe engineisnot running.
Rthe brake system or the power steering is
malfunctioning.
Rthereisamalfunction in the voltage supply
or the vehicle's electrical system.
If your vehicle is being towed, much more
forcemay be necessary to steer or brake.
There isarisk of an accident.
In such cases, useatow bar. Beforetowing,
make sure that the steering moves freely.
GWARNING
If the weight of the vehicle to be towed or tow-
started is greater than the permissible gross
weight of your vehicle:
Rthe towingeye could detach itself
Rthe vehicle/trailer combination could
rollover.
There isarisk of an accident.
When towingortow-starting another vehicle,
its weight should not be greater than the
permissible gross weight of your vehicle.
Information on your vehicle's gross vehicle
weight ratingcan be found on the vehicle
identification plate (Ypage 372).
!If DISTRONIC PLUS or the HOLD function
is activated, the vehicle brakes
automatically in certain situations. To
preventdamage to thevehicle,deactivate
DISTRONICPLUS and the HOLD function in
the following or other similar situations:
Rwhen towing the vehicle
Rin the car wash
!Only secure the tow rope or tow bar at the
towing eyes. Otherwise,the vehicle could
be damaged.
!Do not use the towing eye for recovery,
this could damage the vehicle.Ifindoubt,
recover the vehicle withacrane.
!When towing, pullawayslowly and
smoothly.Ifthe tractive power is too high,
the vehicles could be damaged.
!Do not tow with sling-type equipment.
This could damage the vehicle.
!When towing vehicles with KEYLESS-GO,
use the key instead of the Start/Stop
button. Otherwise, the automatic
transmission may shift to positionPwhen
the driver's or front-passenger door are
opened, which could lead to damage to the
transmission.
!The vehicle can be towedamaximum of
30 miles (50km). The towing speed of
30 mph (50 km/h) must not be exceeded.
If the vehicle has to be towed more than
30 miles(50km), the entire vehicle must be
raised and transported.
328Towing and tow-starting
Breakdown assistance

It is better to have the vehicle transported
than to have it towed.
If the vehicle has suffered transmission
damage, have it transported onatransporter
or trailer.
The automatic transmission must be in
positionNwhen the vehicle is being towed.
The battery must be connected and charged.
Otherwise,you:
Rcannot turn the SmartKey to position2in
the ignition lock
Rcannot shift the automatic transmission to
positionN
iDeactivate the automatic locking feature
(Ypage 83). You could otherwisebelocked
out when pushing or towing the vehicle.
Installing/removing the towing eye
Installing the towing eye
GWARNING
The exhaust tail pipe may be very hot. There
isarisk of burns when removing the rear
cover.
Do not touch the exhaust pipe.Take particular
carewhen removingtherear cover.
Example:towing eye covers
Towing eye covers (AMG vehicles)
The mountings for the removable towing eyes
are located in the bumpers. They are at the
front and at the rear, behind the covers.
XRemove the towing eye from the vehicle
tool kit (Ypage 320).
XPull coverout of the bumper in the
direction of the arrow by inserting your
fingers into the recess.
XPress the mark on coverinwards in the
direction of the arrow.
Towing and tow-starting329
Breakdown assistance
Z

XTake coveroff the opening.
XScrew in and tighten the towing eye
clockwise to the stop.
Removing the towing eye
XUnscrew and remove the towing eye.
XPosition the top of coverin the bumper
and press it in at the bottom until it
engages.
XAttach coverto the bumper and press
until it engages.
XPlace the towing eye in the vehicle tool kit.
Towing the vehicle with the rear axle
raised
!The ignition must be switched off if you
are towing the vehicle with the rear axle
raised. Intervention by ESP®could
otherwise damage the brake system.
Only possible for vehicles without
4MATIC.
XSwitchonthe hazard warning lamps
(Ypage 120).
XTurn the SmartKey to position0in the
ignition lock and remove the SmartKey
from the ignition lock.
XWhen leaving the vehicle, take the
SmartKey or the KEYLESS-GO key with you.
When towing your vehicle with the rear axle
raised, it is importantthat you observe the
safety instructions (Ypage 328).
Towingavehicle with both axles on
theground
It is importantthat you observe the safety
instructions when towing away your vehicle
(Ypage 328).
The automatic transmission automatically
shifts to positionPwhen you open the driver's
or front-passenger door or when you remove
the SmartKey from the ignition lock. In order
to ensure that the automatic transmission
stays in positionNwhen towing the vehicle,
you must observe the following points:
XMake sure that the vehicle is stationary and
the SmartKey in the ignition lock is in
position0.
XTurn the SmartKey to position2in the
ignition lock.
On vehicles with KEYLESS-GO, use the
SmartKey instead of the Start/Stop button
(Ypage 147).
XDepress and hold the brake pedal.
XShift the automatic transmission to
positionN.
XRelease the brake pedal.
XRelease the parking brake.
XSwitch on the hazard warning lamps
(Ypage 120).
XLeave the SmartKey in position2in the
ignition lock.
iWhen towing with the hazard warning
lamps switched on, use the combination
switch as usualtosignalachange of
direction. In this case, only the indicator
lamps for the direction of travel flash. After
resetting the combination switch, the
hazard warning lamp starts flashing again.
Transporting the vehicle
!Only lash the vehicle down by the wheels
or wheel rims, not by parts of the vehicle
such as axle or steering components.
Otherwise, the vehicle could be damaged.
The towing eye can be used to pull the vehicle
ontoatrailer or transporter for transporting
purposes.
330Towing and tow-starting
Breakdown assistance

XTurn the SmartKey to position2in the
ignition lock.
XShift the automatic transmission to
positionN.
As soon as the vehicle is loaded:
XPrevent the vehicle from rolling away by
applying the parking brake.
XShift the automatic transmission to
positionP.
XTurn the SmartKey to position0in the
ignition lock and remove the SmartKey
from the ignition lock.
XSecure the vehicle.
Notes on 4MATIC vehicles
!Vehicles with 4MATICmust not be towed
with either the frontorthe rear axle raised,
as doing so will damage the transmission.
If the vehicle has transmission damage or
damage to the front or rear axle, have it
transported onatransporter or trailer.
In the event of damage to the electrical
system
If the battery is defective, the automatic
transmission will be locked in positionP.To
shift the automatic transmission to position
N,you must provide power to the vehicle's
electrical system in the same way as when
jump-starting (Ypage 326).
Have the vehicle transported onatransporter
or trailer.
Tow-starting (emergency engine
starting)
!Vehicles with automatic transmission
must not be started by tow-starting. This
could otherwise damage the transmission.
You can find information on "Jump-starting"
at (Ypage 326).
Fuses
Important safety notes
GWARNING
If you manipulate or bridgeafaulty fuse or if
you replace it withafuse withahigher
amperage, the electric cables could be
overloaded. This could result inafire. There
isarisk of an accident and injury.
Always replace faulty fuses with the specified
new fuses having the correct amperage.
!Only use fuses that have been approved
for Mercedes-Benzvehicles and which
have the correct fuse ratingfor the system
concerned. Otherwise, componentsor
systems could be damaged.
The fuses in your vehicle serve to close down
faulty circuits. Ifafuse blows,all the
componentsonthecircuit and their functions
stop operating.
Blown fusesmust be replacedwith fuses of
the same rating, which you can recognize by
the color and value. The fuse ratings are listed
in the fuse allocation chart.
Ifanewly inserted fuse also blows, have the
cause traced and rectified ataqualified
specialist workshop, e.g. an authorized
Mercedes-BenzCenter.
Beforechangingafuse
XSecure the vehicle against rolling away
(Ypage 167).
XSwitchoff all electrical consumers.
XTurn the SmartKey to position0in the
ignition lock and remove it (Ypage 147).
or
XOn vehicles with KEYLESS-GO, make sure
the ignition is switched off (Ypage 147).
All indicator lamps in the instrument cluster
must be off.
Fuses331
Breakdown assistance
Z