mirror MERCEDES-BENZ CLS 2014 Owner's Manual

Position of the steering wheel for
driving
The steering wheel is moved to the last
selected position when:
Rthe driver's door is closed
Rwith KEYLESS-GO:you press the Start/
Stop button once on vehicles with
KEYLESS-GO
or
Rwith the SmartKey:you insert the
SmartKey into the ignition lock.
When you close the driver's door with the
ignition switched on, the steering wheel is
also automatically moved to the previously
set position.
The last position of the steering wheel is
stored when you switch off the ignition or
when you store the settingwith the memory
function (Ypage 112).
Crash-responsive EASY-EXIT feature
If the crash-responsiveEASY-EXITfeature is
triggeredinanaccident,the steeringcolumn
will moveupwards when the driver's door is
opened. This occurs irrespective of the
position of the SmartKey in the ignition lock.
This makes it easier to exit the vehicle and
rescue the occupants.
The crash-responsiveEASY-EXITfeature is
only operational if the EASY-EXIT/ENTRY
feature is activated in the on-board computer.
(Ypage 233)
Mirrors
Exterior mirrors
Adjusting theexterior mirrors
GWARNING
You could lose control of your vehicle if you
do the followingwhile driving:
Radjust the driver's seat,head restraint,
steeringwheel or mirrors
Rfasten the seat belt
There isarisk of an accident.
Adjust the driver's seat, head restraint,
steeringwheel and mirror and fasten your
seat belt before starting the engine.
GWARNING
The exterior mirror on the front-passenger
side reduces the size of the image. Visible
objects are actually closer than they appear.
This means that you could misjudge the
distancefrom road users travelingbehind,
e.g. when changinglane. There isarisk of an
accident.
For this reason, alwaysmake sure of the
actual distancefrom the road users traveling
behind by glancingover your shoulder.
XTurn the SmartKey to position1or2in the
ignition (Ypage 147).
XPress buttonfor the left-hand exterior
mirror or buttonfor the right-hand
exterior mirror.
The indicator lamp in the corresponding
button lights up in red.
Mirrors109
Seats, steering wheel and mirrors
Z

The indicator lamp goes out again after
some time. You can adjust the selected
mirror using adjustmentbutton$as long
as the indicator lamp is lit.
XPress adjustmentbutton$up, down,or
to theleft or right until you have adjusted
theexteriormirror to thecorrectposition.
You should haveagood overview of traffic
conditions.
The convex exteriormirrors providealarger
field of vision.
After the engine has been started, the
exterior mirrors are automatically heatedif
the rear window defroster is switched on and
the outside temperature is low. Heating takes
amaximum of 10 minutes.
iThe exterior mirrors can also be heated
manually by switching on the rear window
defroster.
Folding theexterior mirrorsinorout
electrically
XTurn the SmartKey to position1or2in the
ignition (Ypage 147).
XBriefly press button.
Bothexterior mirrors fold in or out.
iMake sure that the exterior mirrors are
always folded out fully while driving. They
could otherwise vibrate.
iIf you are drivingfaster than 30 mp/h
(47 km/h), you can no longer fold in the
exterior mirrors.
Setting theexterior mirrors
If the battery has been disconnected or
completely discharged, the exterior mirrors
must be reset.The exterior mirrors will
otherwise not fold in when you select the
"Fold in mirrors when locking" function in the
on-board computer (Ypage 233)
XTurn the SmartKey to position1in the
ignition lock (Ypage 147).
XBriefly press button.
Folding the exterior mirrors in or out
automatically
If the "Fold in mirrors when locking" function
is activated in the on-board computer
(Ypage 233):
Rthe exterior mirrors fold in automatically as
soon as you lock the vehicle from the
outside.
Rthe exterior mirrors fold out again
automatically as soon as you unlock the
vehicle and then open the driver's or front-
passenger door.
iIf the exterior mirrors have been folded in
manually,they do not fold out.
Exterior mirror pushed out of position
If an exterior mirror has been pushed out of
position, proceed as follows:
XVehicles without electrically folding
exterior mirrors:move the exterior mirror
into the correct position manually.
XVehicles with electrically folding
exterior mirrors:press and hold mirror-
folding buttonuntil you hearaclick and
then the mirrors engage in position
(Ypage 110).
The mirror housing is engaged again and
you can adjust the exterior mirrors as usual
(Ypage 109).
110Mirrors
Seats, steering whee la nd mirrors

Automaticanti-glaremirrors
The rear-view mirror and theexteriormirror
on thedriver'sside automatically go intoanti-
glaremodeifthefollowingconditionsare met
simultaneously:
Rthe ignition is switched on and
Rincident light from headlamps strikes the
sensor in the rear-view mirror.
The mirrors do not go into anti-glare mode if
reverse gear is engaged or if the interior
lighting is switched on.
Parking position for the exterior
mirror on the front-passenger side
Setting and storing the parking position
Using reverse gear
Button for the driver's side exterior mirror
Button for the front-passenger side
exterior mirror
$Adjustment button
!Memory buttonM
You can position the front-passenger side
exterior mirror in suchaway that you can see
the rear wheel on that side as soon as you
engage reverse gear. You can store this
position.
XPark the vehicle and turn the SmartKey to
position2in the ignition lock
(Ypage 147).
XPress buttonfor the exterior mirror on
the front-passenger side.
XEngage reverse gear.
The exterior mirror on the front-passenger
side moves to the preset parking position.
XUse adjustmentbutton$to adjust the
exterior mirror toaposition that allows you
to see the rear wheel and the curb.
The parking position is stored.
iIf you shift the transmission to another
position, the exterior mirror on the front-
passenger side returnstothe driving
position.
Using the memorybutton
Button for the driver's side exterior mirror
Button for the front-passenger side
exterior mirror
$Adjustment button
!Memory buttonM
You can position the front-passenger side
exterior mirror in suchaway that you can see
the rear wheel on that side as soon as you
engage reverse gear. This setting can be
stored using memory buttonM!.
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XWith the exterior mirror on the front-
passenger side activated, use adjustment
button$to adjust the exterior mirror. In
the exterior mirror, the rear wheel and the
curb should be visible.
Mirrors111
Seats, steering wheel and mirrors
Z

XPress memory buttonM!and one of the
arrows on adjustmentbutton$within
three seconds.
The parking position is stored if the exterior
mirror does not move.
XIf the exterior mirror moves out of position,
repeat the steps.
Calling upastored parking position
setting
Button for the driver's side exterior mirror
Button for the front-passenger side
exterior mirror
$Adjustmentbutton
!Memory buttonM
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XAdjust the exterior mirror on the front-
passenger side using button.
XEngage reverse gear.
The exterior mirror on the front-passenger
side moves to the stored parking position.
The exterior mirror on the front-passenger
side moves back to its original position:
Ras soon as you exceedaspeed of9mph
(15 km/h)
Rif you press buttonfor the exterior
mirror on the driver'sside
Memoryfunction
Storing settings
GWARNING
If you use the memoryfunctiononthe driver's
side while driving, you could lose control of
the vehicle asaresult of the adjustments
being made. There isarisk of an accident.
Only use the memory function on the driver's
side when the vehicle is stationary.
GWARNING
Children could become trapped if they
activate the memory function, particularly
when unattended. There isarisk of injury.
When leavingthe vehicle, always takethe
SmartKey with you and lock the vehicle. Never
leave children unsupervised in the vehicle.
With the memory function,you can store up
to three differentsettings, e.g. for three
differentpeople.
The following settings are stored asasingle
memory preset:
Rposition of the seat, backrest and head
restraint
Ractive multicontour seat: seat contour,
dynamic function level
Rdriver's side: position of the exterior
mirrorsonthe driver's and front-passenger
sides
112Memoryfunction
Seats, steering wheel and mirrors

XAdjust the seat(Ypage 100).
XOn the driver'sside, adjust the steering
wheel (Ypage 106)and the exteriormirrors
(Ypage 109).
XPress memory buttonMand one of the
storage position buttons1,2or3within
three seconds.
The settings are stored in the selected
presetposition.Atone sounds when the
settings have been completed.
Calling upastoredsetting
XPressand hold therelevant storage
position button1,2or3until theseat,
steeringwheel and exteriormirrors are in
the stored position.
iThe settingprocedure is interrupted as
soon as you release the storage position
button.
Memory function113
Seats, steering wheel and mirrors
Z

Rif the camera is exposed to very bright light
Rif the area is lit by fluorescentlight or LED
lighting (thedisplay may flicker)
Rif there isasudden change in temperature,
e.g. when drivingintoaheatedgarage in
winter
Rif the camera lens is dirtyorobstructed
Rif the rear of your vehicle is damaged. In
this event, have the camera position and
settingchecked ataqualified specialist
workshop.
General notes
Example: Coupe
Rear view camerais located in the handle
strip of the trunk lid.
Rear view camerais an optical parking and
maneuveringaid. It shows the area behind
your vehicle with guide lines in the COMAND
display.
The area behindthe vehicle is displayed as a
mirror image, as in the rear view mirror.
iThe textofmessages shown in the
COMAND display depends on the language
setting. The following are examples of rear
view camera messages in the COMAND
display.
Activating/deactivating the rear view
camera
XTo activate:make sure that the SmartKey
is in position2in the ignition lock.
XMake sure that the "Activation byRgear"
setting is active in COMAND,see the
separate COMAND operatinginstructions.
XEngage reversegear.
The area behind the vehicle is shown in the
COMAND display with guide lines.
To deactivate:the rear view camera is
deactivated if you:
Rshift the transmission to positionP
Rdrive 33 ft (10 m) forwards
Rshift the transmission fromRto another
position after 15 seconds
Rdrive forwards ataspeed of over5mph
(10 km/h)
Displays in the COMAND display
The rear view camera may showadistorted
view of obstacles, show them incorrectly or
not at all. The rear view camera does not show
objects in the following positions:
Rvery close to the rear bumper
Runder the rear bumper
Rin the area immediately above the tailgate
handle
!Objects not at ground level may appear to
be further away than they actually are, e.g.:
Rthe bumper ofaparked vehicle
Rthe drawbar ofatrailer
Rthe ball coupling ofatrailer tow hitch
Rthe rear section of an HGV
Raslanted post
Use the guidelines only for orientation.
Approachobjects no further than the
bottom-most guideline.
200Driving systems
Driving and parking

Yellow guide line atadistanceof
approximately 13 ft(4.0m)from the rear
of the vehicle
White guide line without turning the
steering wheel, vehicle width including
the exterior mirrors (static)
$CLSCoupe:yellow guide line for the
vehicle width including the exterior
mirrors,for current steering wheel angle
(dynamic)
!Yellow lane marking tires at current
steering wheel angle(dynamic)
Yellow guide line atadistance of
approximately3ft(1.0 m) from the rear
of the vehicle
%Vehicle center axle (marker assistance)
Bumper
Red guide line atadistance of
approximately 12 in (0.30 m) from the
rear of the vehicle
The guide linesare shownwhen the
transmission is in positionR.
The distance specifications only apply to
objectsthat are at ground level.
Additional messages for vehicles withPARKTRONIC
Front warning display
Additional PARKTRONIC measurement
operational readiness indicator
$Rear warning display
Vehicles with PARKTRONIC:if
PARKTRONIC is operational (Ypage 193), an
additional operational readiness indicator will
appearinCOMAND display.Ifthe
PARKTRONIC warning displays are active or
light up, warning displaysand$are also
active or light up correspondingly in the
COMAND display.
Driving systems201
Driving and parking
Z

"Reverse parking" function
Backing up straight intoaparking space
without turning the steering wheel
White guide line without turning the
steering wheel, vehicle width including
the exterior mirrors (static)
CLS Coupe:yellow guide line for the
vehicle width including the exterior
mirrors, for current steering wheel angle
(dynamic)
$Yellowguide line atadistance of
approximately3ft(1.0 m) from the rear
of the vehicle
!Red guide line atadistance of
approximately 12 in (0.30 m) from the
rear of the vehicle
XMake sure that the rear view camera is
switched on (Ypage 200).
The lane and the guide lines are shown.
XWith the help of white guide lines,check
whether the vehicle will fit into the parking
space.
XUsing white guide linesasaguide,
carefully reverse until you reach the end
position.
Red guide line!is then at the end of the
parking space. The vehicle is almost
parallel in the parking space.
Reverse perpendicular parking with the
steering wheel at an angle
Parking space marking
CLS Coupe:yellow guide line for the
vehicle width including the exterior
mirrors, for current steering wheel angle
(dynamic)
XMake sure that the rear view camera is
switched on (Ypage 200).
The lane and the guide lines are shown.
XDrive past the parking space and bring the
vehicle toastandstill.
XWhile the vehicle is atastandstill, turn the
steering wheel in the direction of the
parking space until yellow guide line
reaches parking space marking.
XKeep the steering wheel in that position
and back up carefully.
Backing up with the steering wheel turned
CLS Coupe:yellow guide line for the
vehicle width including the exterior
mirrors, for current steering wheel angle
(dynamic)
202Driving systems
Driving and parking

Problems with Night View Assist Plus
ProblemPossible causes/consequences andSolutions
The picture quality of
Night View Assist Plus
has deteriorated.
The windshield wipers are smearing the windshield.
XReplace the wiper blades (Ypage 126).
The windshield is smeared after the vehicle has been cleaned in a
car wash.
XCleanthe windshield (Ypage 314).
There is windshield chip damage in the camera's field of vision.
XReplace the windshield.
The windshield is fogged up on the inside.
XDefrost the windshield (Ypage 140).
The windshield is iced up.
XDe-ice the windshield (Ypage 139).
There is dirt on the inside of the windshield.
XCleanthe inside of the windshield (Ypage 314).
Lane Tracking package
General notes
The Lane Tracking package consistsofBlind
Spot Assist (Ypage 207) and Lane Keeping
Assist (Ypage 209).
Blind Spot Assist
General notes
Blind Spot Assist usesaradar sensor system
to monitor the areas on both sides of your
vehicle. It supports you fromaspeed of
approximately 20 mph(30km/h).Awarning
displayinthe exteriormirrors draws your
attention to vehicles detected in the
monitored area. If you thenswitchonthe
correspondingturnsignal to change lanes,
you will also receiveavisual and audible
collision warning. BlindSpot Assist uses
sensors in the rear bumper for monitoring
purposes.
For BlindSpot Assist to assist you, the radar
sensor system must be operational.
Important safety notes
GWARNING
BlindSpot Assist does not reactto:
Rvehicles overtaken too closely on the side,
placingtheminthe blind spot area
Rvehicles which approach withalarge speed
differential and overtake your vehicle
Asaresult, Blind Spot Assist may not give
warnings in such situations. There isarisk of
an accident.
Always observe the traffic conditions
carefully, and maintainasafe lateral distance.
Blind Spot Assist is only an aid. It may fail to
detect some vehicles and is no substitute for
attentive driving. Always ensure that there is
sufficient distance to the side for other road
users and obstacles.
iUSA only:
Driving systems207
Driving and parking
Z

This device has been approved by the FCC
asa"Vehicular RadarSystem". The radar
sensor is intended foruse in an automotive
radar system only. Removing, tampering
with, or altering the device will void any
warranties, and is not permitted by the
FCC. Do not tamper with, alter, or use in
any non-approved way.
Any unauthorized modification to this
device could void the user’s authority to
operate the equipment.
Monitoring range of the sensors
In particular, the detection of obstacles can
be impaired if:
Rdirt on the sensors or anything else
covering the sensors
Rpoor visibility, e.g. due to fog, heavy rain,
snow or spray
Rnarrow vehicles, e.g. motorcycles or
bicycles
Rthe road has very wide lanes
Rthe road has narrow lanes
Ryou are not driving in the middle of the lane
Rthere are barriers or similarlane borders
Vehiclesinthemonitoringrangeare then not
indicated.
BlindSpotAssist monitors the area up to
10 ft (3 m) behind your vehicle and directly
next to your vehicle, as shown in the diagram.
If the lanes are narrow, vehicles driving in the
lane beyond the lane next to your vehicle may
be indicated, especially if the vehicles are not
driving in the middle of their lane. This may
be the case if there are vehicles driving at the
inner edge of their lanes.
Due to the nature of the system:
Rwarnings may be issued in error when
driving close to crash barriers or similar
solid lane borders.
Rthe warning is canceled when driving for an
extended period next to long vehicles, such
as trucks.
The two radar sensors for Blind Spot Assist
are integrated into the sides of the rear
bumper. Make sure that the bumper is free of
dirt, ice or slush in the vicinity of the sensors.
The sensors must not be covered, for
example by cycle racks or overhanging loads.
Followingasevere impact or in the event of
damage to the bumpers, have the function of
the sensors checked ataqualified specialist
workshop. Blind Spot Assist may otherwise
not work properly.
Indicator and warning display
Yellowindicator lamp/red warning lamp
Active Blind Spot Assist is not active at
speeds below approximately 20 mph
(30 km/h). Vehicles in the monitoring range
are then not indicated.
When Blind Spot Assist is activated, indicator
lampin the exterior mirrors lights up
yellow at speeds of up to 20 mph(30km/h).
At speeds above 20 mph (30 km/h) the
208Driving systems
Driving and parking