reset MERCEDES-BENZ CLS 2014 Owner's Manual

Automaticanti-glaremirrors
The rear-view mirror and theexteriormirror
on thedriver'sside automatically go intoanti-
glaremodeifthefollowingconditionsare met
simultaneously:
Rthe ignition is switched on and
Rincident light from headlamps strikes the
sensor in the rear-view mirror.
The mirrors do not go into anti-glare mode if
reverse gear is engaged or if the interior
lighting is switched on.
Parking position for the exterior
mirror on the front-passenger side
Setting and storing the parking position
Using reverse gear
Button for the driver's side exterior mirror
Button for the front-passenger side
exterior mirror
$Adjustment button
!Memory buttonM
You can position the front-passenger side
exterior mirror in suchaway that you can see
the rear wheel on that side as soon as you
engage reverse gear. You can store this
position.
XPark the vehicle and turn the SmartKey to
position2in the ignition lock
(Ypage 147).
XPress buttonfor the exterior mirror on
the front-passenger side.
XEngage reverse gear.
The exterior mirror on the front-passenger
side moves to the preset parking position.
XUse adjustmentbutton$to adjust the
exterior mirror toaposition that allows you
to see the rear wheel and the curb.
The parking position is stored.
iIf you shift the transmission to another
position, the exterior mirror on the front-
passenger side returnstothe driving
position.
Using the memorybutton
Button for the driver's side exterior mirror
Button for the front-passenger side
exterior mirror
$Adjustment button
!Memory buttonM
You can position the front-passenger side
exterior mirror in suchaway that you can see
the rear wheel on that side as soon as you
engage reverse gear. This setting can be
stored using memory buttonM!.
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XWith the exterior mirror on the front-
passenger side activated, use adjustment
button$to adjust the exterior mirror. In
the exterior mirror, the rear wheel and the
curb should be visible.
Mirrors111
Seats, steering wheel and mirrors
Z

XPress memory buttonM!and one of the
arrows on adjustmentbutton$within
three seconds.
The parking position is stored if the exterior
mirror does not move.
XIf the exterior mirror moves out of position,
repeat the steps.
Calling upastored parking position
setting
Button for the driver's side exterior mirror
Button for the front-passenger side
exterior mirror
$Adjustmentbutton
!Memory buttonM
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XAdjust the exterior mirror on the front-
passenger side using button.
XEngage reverse gear.
The exterior mirror on the front-passenger
side moves to the stored parking position.
The exterior mirror on the front-passenger
side moves back to its original position:
Ras soon as you exceedaspeed of9mph
(15 km/h)
Rif you press buttonfor the exterior
mirror on the driver'sside
Memoryfunction
Storing settings
GWARNING
If you use the memoryfunctiononthe driver's
side while driving, you could lose control of
the vehicle asaresult of the adjustments
being made. There isarisk of an accident.
Only use the memory function on the driver's
side when the vehicle is stationary.
GWARNING
Children could become trapped if they
activate the memory function, particularly
when unattended. There isarisk of injury.
When leavingthe vehicle, always takethe
SmartKey with you and lock the vehicle. Never
leave children unsupervised in the vehicle.
With the memory function,you can store up
to three differentsettings, e.g. for three
differentpeople.
The following settings are stored asasingle
memory preset:
Rposition of the seat, backrest and head
restraint
Ractive multicontour seat: seat contour,
dynamic function level
Rdriver's side: position of the exterior
mirrorsonthe driver's and front-passenger
sides
112Memoryfunction
Seats, steering wheel and mirrors

XAdjust the seat(Ypage 100).
XOn the driver'sside, adjust the steering
wheel (Ypage 106)and the exteriormirrors
(Ypage 109).
XPress memory buttonMand one of the
storage position buttons1,2or3within
three seconds.
The settings are stored in the selected
presetposition.Atone sounds when the
settings have been completed.
Calling upastoredsetting
XPressand hold therelevant storage
position button1,2or3until theseat,
steeringwheel and exteriormirrors are in
the stored position.
iThe settingprocedure is interrupted as
soon as you release the storage position
button.
Memory function113
Seats, steering wheel and mirrors
Z

The blueindicator lamp in the
instrument cluster lights up when the high-
beam headlamps are switched on.
XTo switch off the high-beam
headlamps:move the combination switch
back to its normal position.
The blueindicator lamp in the
instrument cluster goes out.
iVehicles with Adaptive Highbeam Assist:
when Adaptive Highbeam Assist is active,
it controls activation of the high-beam
headlamps (Ypage 121).
High-beam flasher
High-beam headlamps
Turn signal, right
$High-beam flasher
!Turn signal, left
XTo switch on:turn the SmartKey in the
ignition lock to position1or2,orstart the
engine.
XPull the combination switch in the direction
of arrow$.
Hazard warning lamps
XTo switch on the hazard warning lamps:
press button.
All turn signals flash. If you now switch on
aturn signal using the combination switch,
only the turn signal lamp on the
corresponding side of the vehicle will flash.
XTo switch off the hazard warning
lamps:press button.
The hazard warning lamps automatically
switch on if:
Ran air bag is deployed
Rthe vehicle decelerates rapidly from a
speed of more than 45 mph (70 km/h) and
comes toastandstill
The hazard warning lamps switch off
automatically if the vehicle reachesaspeed
of over6mph (10 km/h) again afterafull
brake application.
iThe hazard warning lamps still operate if
the ignition is switched off.
Headlampcleaning system
The headlamps are cleaned automatically if
the "Wipe with washer fluid" function is
operated five times (Ypage 125)while the
lightsare on and the engineisrunning. When
you switchoff the ignition, the automatic
headlamp cleaning systemisreset and
counting is resumed from 0.
120Exterior lighting
Lights and windshield wipers

drivingstyle in termsofconsumption,taking
the actual and selected conditionsinto
consideration.Your driving style can
significantly influence the vehicle's
consumption.
The ECO display consistsofthree bars:
RAcceleration
RConstant
RCoasting
The percent value is the average value of the
three bars. The three bars and the mean value
begin at the value of 50%.Ahigher
percentage indicatesamoreeconomical
driving style.
The ECO display doesnot indicate the actual
fuelconsumption andafixedpercentage
count in the ECO display doesnot indicate a
fixedconsumption figure.
Apart from driving style, consumption is
dependent on many factors such as,e.g.:
Rload
Rcheck
Rcoldstart
Rchoice of route
Relectrical consumers switched on
These factors are not taken into
consideration by the ECO display.
The evaluation of your driving styleiscarried
outusing the following three categories:
RAcceleration(evaluation of all
acceleration processes):
-The bar fills up: moderate acceleration,
especially at higher speeds
-The bar empties: sporty acceleration
RConstant(assessment of driving behavior
at all times):
-The bar fills up: constant speed and
avoidance of unnecessary acceleration
and deceleration
-The bar empties: fluctuations in speed
RCoasting(assessment of all deceleration
processes):
-The bar fills up: anticipatory driving,
keeping your distance and early release
of the accelerator. The vehicle can coast
without use of the brakes.
-The bar empties: frequent braking
iAn economical driving style specially
requires driving at moderate engine
speeds.
To achieveahigher value in the categories
AccelerationandConstant:
Robserve the gearshift recommendations.
Rdrive in drive programE.
iOn long journeys ataconstant speed, e.g.
on the highway, only the bar forConstant
will change.
iThe ECO displaysummaries the driving
characteristics from the start of the journey
to its completion. For this reason, the bars
change dynamically at the beginning of the
journey. On longer journeys, there are
fewer changes. For more dynamic changes,
carry outamanual reset.
Further information on the ECO display
(Ypage 223).
Driving tips171
Driving and parking
Z

Warning and display messages in the
multifunction display
XActivate ATTENTION ASSIST using the on-
board computer (Ypage228).
If ATTENTION ASSIST is active, you willbe
warned no sooner than 20 minutes after
yourjourney has begun. You then hear an
intermittent warning tonetwice and the
Attention Assist:Drowsiness
detectedmessage appears in the
multifunction display.
XIf necessary, takeabreak.
XPressthebutton to confirmthe
message.
On longjourneys, takeregular breaksingood
timetoallow yourself to rest properly. If you
do not takeabreak,you will be warned again
after 15 minutes at theearliest. The
preconditionfor this is that
ATTENTION ASSIST still detectstypical
indicators of fatigue or increasing lapses in
concentration.
When ATTENTION ASSIST is deactivated, the

symbol and OFF appear in the
multifunction display in the assistance
graphics display when the engine is running.
ATTENTION ASSIST is reset when you
continue your journey and startsassessing
your tiredness again if:
Ryou switch off the engine.
Ryou take off your seat belt and open the
driver's door, e.g. forachange of drivers or
to takeabreak.
Night View Assist Plus
Important safety notes
Night View Assist Plus is only an aid and is not
asubstitute for attentive driving. Do not rely
on the Night View Assist Plus display.You are
responsible for the distance to the vehicle in
front,for vehicle speed and for braking in
good time. Drive carefully and always adapt
your driving style to suit the prevailing road
and traffic conditions.
The system may be impaired or may not
function if:
Rthere is poor visibility, e.g. due to snow,
rain, fog or spray
Rthe windshield is dirty, fogged up or
covered, for instance byasticker, in the
vicinityofthe camera
Ron bends, on uphill gradients or downhill
gradients
Pedestrian recognition may be impaired or
inoperative if:
Rpedestrians are partially or entirely
obscured by objects, e.g. parked vehicles
Rthe silhouette of the pedestrian in the Night
View Assist Plus display is incompleteor
interrupted, e.g. by powerful light
reflections
Rpedestrians do not contrast adequately
from the background
Rpedestrians are not in an upright position,
e.g. sitting, squatting or lying
In addition to the illumination provided by the
normal headlamps, Night View Assist Plus
uses infrared light to illuminate the road.
Night View Assist Plus camerapicks up
the infrared light and displaysamonochrome
image in COMAND. The image displayed in
COMAND corresponds toaroad lit up by high-
beam headlamps. This enables you to see the
road's course and any obstacles in good time.
If pedestrian recognition is activated,
pedestrians recognized by the system are
204Driving systems
Driving and parking

Text fieldshows the selected menu or
submenu as well as display messages.
The following messages may appear in the
multifunction display:
\nShift recommendation (Ypage 161)
 Active Parking Assist (Ypage 196)
Adaptive Highbeam Assist
(Ypage 122)
ECO start/stop function
(Ypage 150)
HOLD function (Ypage 186)
Menus and submenus
Menu overview
Press the\norbutton on the
steeringwheel to call up the menu bar and
selectamenu.
Operating the on-board computer
(Ypage 220).
Dependingonthe equipment installed in the
vehicle, you can call up the following menus:
RTripmenu (Ypage 222)
RNavimenu (navigation instructions)
(Ypage 224)
RAudiomenu (Ypage 225)
RTelmenu (telephone) (Ypage 226)
RDriveAssistmenu (assistance)
(Ypage 227)
RServ.menu (Ypage 229)
RSettingsmenu (settings) (Ypage 229)
RAMGmenu in AMG vehicles (Ypage 234)
Trip menu
Standard display
XPress and hold thebutton on the
steeringwheel until theTripmenu with
trip odometerand odometeris
shown.
Trip computer "From Start" or "From
Reset"
Example: trip computer "From Start"
Distance
Time
$Average speed
!Average fuel consumption
XPress the\norbutton on the
steeringwheel to select theTripmenu.
XPressorto selectFrom Start
orFrom Reset.
The values in theFrom Startsubmenu are
calculated from the start ofajourney whilst
the values in theFrom Resetsubmenu are
calculated from the last time the submenu
was reset (Ypage 223).
TheFrom Starttrip computer is
automatically reset when:
Rthe ignition has been switched off for more
than four hours.
R999 hours have been exceeded.
R9,999 miles have been exceeded.
222Menus and submenus
On-board computer and displays

TheFrom Resettrip computer is
automatically reset if the value exceeds
9,999 hours or 99,999miles.
ECO display
Example: ECO display
XPress the\norbutton on the
steeringwheel to select theTripmenu.
XSelectECO DISPLAYwithor.
If the ignition remains switched off for longer
than four hours, the ECO display will be
automatically reset.
Further information on the ECO display
(Ypage 170).
Displaying the range and current fuel
consumption
XPress the\norbutton on the
steeringwheel to select theTripmenu.
XPress theorbutton to select the
currentfuel consumption (not for AMG
vehicles) and the approximate range.
The approximate range that can be covered
depends on the fuel level and your current
driving style. If there is onlyasmall amount
of fuel left in the fuel tank,the display shows
avehicle being refueledinstead of the
range.
Digital speedometer
Shift recommendation (Ypage 161)
Digital speedometer
XPress the\norbutton on the
steeringwheel to select theTripmenu.
XPress theorbutton to select the
digital speedometer.
iIf the gearshift recommendation is shown
at the top of the multifunction display,itis
no longer shown at the bottom of the
multifunction display.
Resetting values
Example: resetting the trip computer "From Start"
XPress the\norbutton on the
steeringwheel to select theTripmenu.
XPress theorbutton to select the
function that you wish to reset.
XPress thebutton.
XPress thebutton to selectYesand
press thebutton to confirm.
You can reset the values of the following
functions:
RTrip odometer
R"From Start" trip computer
R"From Reset" trip computer
RECO display
Menus and submenus223
On-board computer and displays
Z

iWhen you reset the values in the "ECO
display",the values in the trip computer
"From start"are likewise reset. When you
reset the values in the trip computer "From
start", the values in the "ECO display" are
likewise reset.
Navigation system menu
Displaying navigation instructions
In theNavimenu, the multifunction display
shows navigation instructions. For more
information on navigation,see the separate
operatinginstructions.
XSwitchonCOMAND (see the separate
operatinginstructions).
XPress the\norbutton on the
steering wheel to select theNavimenu.
Routeguidance not active
Direction of travel
Current road
Routeguidance active
No change of direction announced
Distance to the destination
Distance to the nextchange of direction
$Current road
!"Follow the road's course" symbol
Change of direction announced without a
lane recommendation
Road intowhich the change of direction
leads
Distance to change of direction and visual
distancedisplay
$Change-of-direction symbol
Whenachange of direction is announced, you
will see symbol$for the change of direction
and distancegraphic.The distance
indicator shortenstowards the top of the
displayasyou approach the point of the
announced change of direction.
Change of direction announced with a
lane recommendation
Road into which the change of direction
leads
Distancetochange of direction and visual
distance display
$New lane duringachange of direction
!Uninterrupted lane
Lane recommendation
%Change-of-direction symbol
On multilane roads, the system can display
lane recommendation$for the next change
of direction. During the change of direction,
additional lanes may be displayed.
Lane recommendations are only displayed if
the relevant data is available on the digital
map.
224Menus and submenus
On-board computer and displays

mirrors willnot fold out automatically
(Ypage110).
You can then only fold out the exterior mirrors
using button.
Restoringthe factory settings
XPress the\norbutton on the
steering wheeltoselect theSett.menu.
XPress theorbutton to select the
Factory Settingsubmenu.
XPressto confirm.
TheReset All Settings?message
appears.
XPress theorbutton to select
NoorYes.
XPressto confirm the selection.
If you have selectedYes,the multifunction
display showsaconfirmation message.
For safety reasons, theDaytime Running
Lightsfunction in theLightssubmenu is
only reset if the vehicleisstationary.
AMG menu in AMG vehicles
AMG displays
Digital speedometer
Gear indicator
$Upshift indicator
!Engine oil temperature
Coolant temperature
%ECO start/stop function status indicator
(Ypage 151)
XPress the\norbutton on the
steering wheel to select theAMGmenu.
Upshift indicatorUP$indicates that the
engine has reached the overrevving range
when in the manual gearshift program.
Upshift indicatorUP$fades out other
messages until you have shifted up.
When the engine oil temperature is below
176‡(80 †) the oil temperature is shownin
blue. Avoid drivingatfull engineoutput during
this time.
SETUP
Driveprogram (C/SS+/M)
ESP®mode (ON/OFF)orSPORT handling
mode (SPORT)
$Suspension tuning(COMFORT/SPORT/
SPORT+)
SETUP shows the drive program, the ESP®
(Electronic Stability Program) mode and the
suspension tuning.
XPress the\norbutton on the
steering wheel to select theAMGmenu.
XPress thebutton repeatedly until
SETUP is displayed.
or
XBriefly press the AMG button on the center
console (Ypage 191).
234Menus and submenus
On-boar dc omputer and displays