warning light MERCEDES-BENZ CLS 2014 Owner's Manual

60 seconds or until the driverorfront
passenger have fastenedtheir seatbelts.
If the driver/frontpassenger unfasten their
seat belt while the vehicle is in motion,the
seat belt warning lamp lights up and a
warning tonesounds again.
The warning toneceases even if the driver or
front-passenger seat belt has still not been
fastened after 60 seconds. Theseat belt
warning lamp stops flashing but remains
illuminated.
After the vehicle comes toastandstill, the
warning toneisreactivated and the seat belt
warning lampflashes again if the vehicle
speed again exceeds 15 mph (25 km/h).
Theseat belt warning lamp only goes
out if:
Rboth the driver and the frontpassenger
have fastened their seat belts.
or
Rthevehicle is stationaryandadoor is open.
iFor moreinformationontheseat
belt warning lamp, see "Warning and
indicator lamps in theinstrumentcluster,
seat belts" (Ypage 265).
Emergency TensioningDevices, seat
belt force limiters
GWARNING
Pyrotechnic Emergency Tensioning Devices
that have been deployed are no longer
operational and are unable to performtheir
intended protective function. This poses an
increased risk of injury or even fatal injury.
Therefore, have pyrotechnic Emergency
Tensioning Devices which have been
triggered immediately replaced ataqualified
specialist workshop.
!If the front-passenger seat is not
occupied, do not engage the seat belt
tongue in the buckle on the front-
passenger seat. Otherwise, the Emergency
Tensioning Device could be triggered in the
event of an accident.
iVehicles with PRE-SAFE®:Emergency
Tensioning Devices that are triggered by an
electric motor can be deployed as often as
desired and do not need to be replaced.
The front seat belts and the outer seat belts
in the rear are equipped with Emergency
Tensioning Devices and seat belt force
limiters.
The ETDs tighten the seat belts in an accident,
pulling them close against the body.
The ETDs do not correct incorrectseat
positions or incorrectly fastened seat belts.
The ETDs do not pull vehicle occupants back
towards the backrest.
The ETDs can only be activated when:
Rthe ignition is switched on
Rthe restraint systems are operational; see
"SRS warning lamp"(Ypage 41)
Rthe belt tongue is engaged in the buckle on
each of the front seat belts.
The ETDs on the outside seats in the rear
compartmentare triggeredindependently of
the lock status of the seat belts.
The ETDs are triggereddepending on the type
and severity of an accident:
Rif, in the event ofahead-on or rear-end
collision, the vehicledecelerates or
accelerates rapidly inalongitudinal
direction during the initialstages of the
impact
Rif,inthe event ofasideimpact,onthe side
opposite the impact the vehicle
decelerates or accelerates rapidlyina
lateraldirection
Rif,incertainsituations where the vehicle
rolls over,the system determines that it
can provide additional protection
If the ETDsare deployed, you will hearabang,
andasmall amountofpowder may also be
released. Only in rare cases will the bang
affect your hearing. The powder that is
released generally does not constitute a
Occupant safety59
Safety
Z

health hazard and does not indicate that there
isafire in the vehicle. The dust might cause
some temporary breathing difficulty for
people with asthma or other breathing
trouble. To avoid this, you may wish to get out
of the vehicle as soon as it is safe to do so.
You can also open the window to allow fresh
air to enter the vehicle interior. TheSRS
warning lamp lights up.
If the seat belt is also equipped withaseat
belt force limiter and this is triggered, the
force exerted by the seat belt on the vehicle
occupant is reduced.
The seat belt force limiters for the front seats
are synchronized with the front air bags,
which take onapart of the deceleration force.
This results in the force exerted on the
occupant being distributed overagreater
area.
Children in the vehicle
Child restraint systems
Important safety notes
GWARNING
According to accident statistics, children are
safer when properly restrained in the rear
seating positions than in the front seating
position. Thus, we strongly recommendthat
children be placed in the rear seats whenever
possible. Regardless of seating position,
children 12 years old and under must be
seated and properly secured in an appropriate
infant restraint,toddler restraint,orbooster
seat recommended for the size and weight of
the child.
The infant or child restraint must be properly
secured with the vehicle's seat belt, the seat
belt and top tether strap, or lower anchors and
top tether strap, fully in accordance with the
child seat manufacturer's instructions.
Occupants, especially children, should always
sit as upright as possible, wear the seat belt
properly and use an appropriately sized infant
restraint,toddler restraint,orbooster seat
recommended for the size and weight of the
child.
Children can be killed or seriously injured by
an inflating air bag. Note the following
important information when circumstances
require you to placeachild in the front
passenger seat:
RYour vehicle is equipped with air bag
technology designed to deactivate the front
passenger front air bag in your vehicle
when the system senses the weight of a
typical 12-month-old child or less along
with the weight ofastandard appropriate
child restraint on the front passenger seat.
RFor children larger than the typical
12-month-old child, the front passenger
front air bag may or may not be activated.
Always make sure theindicator
lamp is illuminated, indicatingthat the front
passenger front air bag is deactivated.
RAchild inarear-facing child restraint on the
front passenger seat will be seriously
injured or even killed if the front passenger
front air bag inflates inacollision which
could occur under some circumstances,
even with the air bag technology installed
in your vehicle. The only means to
completely eliminate this risk is to never
placeachild inarear-facing child restraint
in the front seat. We therefore strongly
recommendthat you always placeachild
inarear-facing child restraint inabackseat.
RIf you must installarear-facing child
restraint on the front passenger seat
because circumstances require you to do
so, make sure theindicator
lamp is illuminated, indicatingthat the front
passenger front air bag is deactivated.
Should theindicator lamp not
illuminateorgoout while the restraint is
installed, please checkinstallation.
Periodically check theindicator
lamp while drivingtomake sure the
indicator lamp is illuminated. If the
indicator lamp goes out or
remainsout, do not transportachild on the
60Children in thevehicle
Safety

GWARNING
If children are left unsupervised in the vehicle,
they could:
Ropen the doors, thus endangering other
people or road users.
Rget out and disrupt traffic.
Roperate the vehicle's equipment.
Additionally, children couldset the vehiclein
motion if, for example, they:
Rrelease the parking brake.
Rshifting the automatic transmission out of
park positionP
RStart the engine.
There isarisk of an accident and injury.
When leaving the vehicle, alwaystake the
SmartKey with you and lock the vehicle. Never
leave children or animals unattended in the
vehicle. Always keep the SmartKey out of
reach of children.
GWARNING
If persons, particularlychildren are subjected
to prolonged exposure to extreme heator
cold,there isariskofinjury,possiblyeven
fatal. Never leave children unattendedinthe
vehicle.
GWARNING
If the child restraint system is subjected to
direct sunlight, parts may get very hot.
Children mayburn themselves on these parts,
particularly on the metal parts of the child
restraint system. There isarisk of injury.
If you leave the vehicle, takingthe child with
you, alwaysensure that the child restraint
system is not exposed to direct sunlight.
Protectitwithablanket,for example. If the
child restraint system has been exposed to
direct sunlight, let it cool down before
securing the child in it. Never leave children
unattended in the vehicle.
If an infantorchild is traveling in the vehicle:
RSecure the child withachild or infant seat
restraint system appropriate to the age and
weight of the child.
RMake sure that the infant or child is
properly secured at all times while the
vehicle is in motion.
Mercedes-Benzrecommends that you always
properly secure all infants and children with
achild or infantseat restraint system for the
trip.
The use of seat belts and infantand child
restraint systemsisrequired by lawin:
Rall50states
Rthe U.S. territories
Rthe District of Columbia
RallCanadianprovinces
Infants and children must alwaysbeseated in
an appropriate infant or child restraint system
recommendedfor the size and weight of the
child.The infant or child restraint system
must be properly secured in accordance with
the manufacturer's instructions.
All infant or child restraint systems must meet
the following standards:
RU.S. Federal Motor Vehicle Safety
Standards 213 and 225
RCanadianMotor Vehicle Safety Standards
213 and 210.2
Confirmation that the child restraint system
corresponds to the standards can be found
on an instruction label on the child restraint
system. This confirmation can also be found
in the installation instructions that are
included with the child restraint system.
Always read and follow the manufacturer's
instructions when using an infant or child
restraint system or booster seat.
Observe the warning labels in the vehicle
interior or on the infant or child restraint.
62Children in the vehicle
Safety

ABS works fromaspeedof about5mph
(8 km/h)upwards,regardless of road-surface
conditions.ABS works on slippery surfaces,
evenifyou only brake gently.
The yellowABS warning lamp in the
instrument cluster lights up when the ignition
is switched on. It goes out when the engine is
running.
Braking
XIf ABS intervenes:continue to depress the
brake pedal vigorously until the braking
situation is over.
XTo makeafull brake application:
depress the brake pedal with full force.
If ABS intervenes when braking, you will feel
apulsing in the brake pedal.
The pulsating brake pedal can be an
indication of hazardous road conditions, and
functions asareminder to take extracare
while driving.
BAS (Brake Assist System)
iObserve the "Important safety notes"
section (Ypage 66).
GWARNING
If BAS is malfunctioning, the braking distance
in an emergencybraking situation is
increased. There isarisk of an accident.
In an emergencybraking situation, depress
the brake pedal with full force. ABS prevents
the wheels from locking.
BAS operates in emergencybraking
situations. If you depress the brake pedal
quickly, BAS automatically boosts the braking
force, thus shortening the stopping distance.
The brakes will function as usual once you
release the brake pedal. BAS is deactivated.
BAS PLUS (Brake Assist System
PLUS)
General information
iObserve the "Important safety notes"
section (Ypage 66).
BAS PLUS is only available in vehicles
equipped with DISTRONIC PLUS.
For BAS PLUS to assist you when driving, the
radar sensor system must be:
Ractivated (Ypage 232)
Roperational
With the help of the radar sensor system, BAS
PLUS can detect obstacles that are in the
path of your vehicle for an extended period of
time.
If the radar sensor system is malfunctioning,
BAS PLUS will not be available. The brake
system is still available with complete brake
boosting effect and BAS.
BAS PLUS provides braking assistance in
hazardous situations at speeds greater than
4mph (7 km/h).
At speeds of up to approximately 40 mph
(70 km/h),BAS PLUS can also react to
stationary objects. Examples of stationary
objectsare stopped or parked vehicles.
Important safety notes
GWARNING
BAS PLUS cannot alwaysclearly identify
objectsand complex traffic situations. BAS
PLUS cannot intervene in these cases. There
isarisk of an accident.
Always pay careful attention to the traffic
situation and be ready to brake.
GWARNING
BAS PLUS does not react:
Rto people or animals
Rto oncoming vehicles
Rto crossingtraffic
Rwhen cornering
Driving safety systems67
Safety
Z

Asaresult, BAS PLUS may not intervene in all
critical situations. There isarisk of an
accident.
Always pay careful attention to the traffic
situation and be ready to brake.
In particular, the detection of obstacles can
be impaired if there is:
Rdirt on the sensorsoranythingelse
covering the sensors
Rsnow or heavy rain
Rinterference by other radar sources
Rthere are strong radar reflections, for
example in parking garages
Ranarrow vehicle travelinginfront, e.g. a
motorbike
Ravehicle travelinginfrontonadifferent line
relative to the center of your vehicle
Following damage to the frontend of the
vehicle, have the configurationand operation
of the radarsensorschecked ataqualified
specialist workshop. This also applies to
collisions at low speeds where thereisno
visible damage to the frontofthe vehicle.
Braking assistance
To preventacollision with the vehicle in front,
BAS PLUS calculates the brake force
necessary if:
Ryou approach an obstacle, and
RBAS PLUS has detectedarisk of collision
When driving ataspeed under 20 mph
(30 km/h):ifyou depress the brake pedal,
BAS PLUS is activated. The increase in brake
pressure will be carried out at the last
possible moment.
When driving ataspeed greater than
20 mph (30 km/h):ifyou depress the brake
pedal sharply, BAS PLUS automatically raises
the brake pressure toavalue adapted to the
traffic situation.
If BAS PLUS demands particularly high
braking force, preventative passenger
protection measures (PRE-SAFE®)are
activated simultaneously.
XKeep the brake pedal depressed until the
emergencybraking situation is over.
ABS preventsthe wheels from locking.
BAS PLUS is deactivated and the brakes
function as usual if:
Ryou release the brake pedal
Rthere is no longerarisk of collision
Rno obstacle is detected in front of your
vehicle
ESP®(Electronic Stability Program)
Important safety notes
iObserve the "Important safety notes"
section (Ypage 66).
GWARNING
If ESP®is malfunctioning, ESP®is unable to
stabilize the vehicle. Additionally, further
driving safety systems are deactivated. This
increases the risk of skidding and an accident.
Drive on carefully. Have ESP®checked at a
qualified specialist workshop.
!Vehicles with 4MATIC: switch off the
ignition when the parking brake is being
tested onabrake dynamometer.
Application of the brakes by ESP®may
otherwise destroy the brake system.
Vehicles without 4MATIC: observe the notes
on ESP®(Ypage 330) when towing the
vehicle witharaised rear axle.
ESP®is deactivated if the warning lamp
in the instrument cluster lights up
continuously when the engine is running.
If thewarning lamp and the
warning lamp are lit continuously, ESP®is not
available due toamalfunction.
Observe the information on warning lamps
(Ypage 269) and display messages which
may be shown in the instrument cluster
(Ypage 238).
68Driving safety systems
Safety

If ESP®detects that the vehicle is deviating
from the direction desiredbythe driver, one
or more wheels are braked to stabilize the
vehicle.The engine output is also modified to
keep the vehicle on the desired course within
physical limits. ESP®assists the driver when
pulling away on wet or slippery roads. ESP®
can also stabilize the vehicle during braking.
If ESP®intervenes, theESP®warning
lamp flashes in the instrumentcluster.
If ESP®intervenes:
XDo not deactivateESP®under any
circumstances.
XOnly depressthe accelerator pedal as far
as necessary when pulling away.
XAdapt your drivingstyle to suit the
prevailing road and weatherconditions.
iOnly use wheels with the recommended
tire sizes. Only then will ESP®function
properly.
ETS/4ETS (Electronic Traction System)
ETS/4ETS traction control is part of ESP®.
Traction control brakes the drive wheels
individuallyifthey spin. This enables you to
pull away and accelerate on slippery surfaces,
for example if the road surface is slippery on
one side. In addition, more drive torque is
transferred to the wheel or wheels with
traction.
Traction control remains active, even if you
deactivate ESP®.
Deactivating/activating ESP®(except
AMG vehicles)
GWARNING
If you deactivate ESP®,ESP®no longer
stabilizes the vehicle. There is an increased
risk of skidding and an accident.
Only deactivate ESP®in the situations
described in the following.
!Avoid spinningthe driven wheels for an
extended period with ESP®deactivated.
You could otherwise damage the drivetrain.
XTo deactivate:(Ypage 227).
The ESP®OFF warning lamp in the
instrument cluster lights up.
XTo activate:(Ypage 227).
The ESP®OFF warning lamp in the
instrument cluster goes out.
ESP®is activated automatically when the
engine is started.
The ECO start/stop function switches the
engine off automatically when the vehicle
stops moving. The engine starts
automatically when the driver wants to pull
away again. ESP®remains in its previously
selected status. Example: if ESP®was
deactivated before the engine was switched
off, ESP®remains deactivated when the
engine is switched on again.
If ESP®is deactivated and one or more wheels
start to spin, theESP®warning lamp in
the instrument cluster flashes. In such
situations, ESP®will not stabilize the vehicle.
It may be best to deactivate ESP®in the
following situations:
Rwhen using snow chains
Rin deep snow
Ron sand or gravel
If you deactivate ESP®:
RESP®no longer improves driving stability.
Rtraction control is still activated.
RESP®still provides support when you
brake.
Rengine torque is not limited and the drive
wheels are able to spin. The spinning
wheels produceacutting effect for better
traction.
Driving safety systems69
Safety
Z

Deactivating/activating ESP®(AMG
vehicles)
Activating/deactivating SPORT handling
mode
GWARNING
WhenSPORT handling mode is activated,
there isagreater risk of skidding and
accidents.
Only activateSPORT handling mode in the
situations described in the following.
XTo activate:briefly press button.
TheSPORT handling mode warning
lamp in the instrument cluster lights up.
TheSPORT handling modemessage
appears in the multifunction display.
SPORT handling mode is designed for
driving on designated roads when the
vehicle's own oversteering and
understeering characteristics are desired.
DrivinginSPORT handling mode requires
an extremely qualified and experienced
driver who is able to cope with these critical
driving conditions.
XTo deactivate:briefly press button.
TheSPORT handling mode warning
lamp in the instrument cluster goes out.
ESP®is activated automatically when the
engine is started.
It may be best to activateSPORT handling
mode in the following situations:
Rwhen using snow chains
Rin deep snow
Ron sand or gravel
If SPORT handling mode is activated and one
or more wheels start to spin, theESP®
warning lamp in the instrument cluster
flashes. ESP®only stabilizes the vehicle to a
limited degree.
When SPORT handling mode is activated:
RESP®only improves driving stability to a
limited degree.
Rtraction control is still activated.
RESP®still provides support when you
brake.
Rengine torque is only restricted toalimited
degree, and the drive wheels are able to
spin. The spinningwheels produce a
cutting effect for better traction.
Vehicles with ECO start/stop function: the
ECO start/stop function switches the engine
off automatically when the vehicle comes to
astop. The engine startsautomatically when
the driver wants to pull away again. ESP®
remains in its previously selected status. For
example, if ESP®was deactivated before the
engine was switched off, ESP®remains
deactivated when the engine is switched on
again.
Deactivating/activating ESP®
GWARNING
If you deactivate ESP®,ESP®no longer
stabilizes the vehicle. There is an increased
risk of skidding and an accident.
Only deactivate ESP®in the situations
described in the following.
!Avoid spinningthe driven wheels for an
extended period with ESP®deactivated.
You could otherwise damage the drivetrain.
70Driving safety systems
Safety

XTo deactivate:press buttonuntilthe
ESP®OFF warning lamp lights up in
the instrument cluster.
TheOFFmessage appearsinthe
multifunctiondisplay.
Deactivate ESP®when drivingon
designated roads when the vehicle's own
oversteeringand understeering
characteristics are desired. Drivingwithout
ESP®requiresanextremely qualified and
experienced driverwho is able to cope with
these critical driving conditions.
XTo activate:briefly press button.
The ESP®OFF warning lamp in the
instrumentcluster goes out. TheON
message appears in the multifunction
display.
ESP®is activated automatically when the
engine is started.
If ESP®is deactivated and one or morewheels
start to spin,theESP®warninglamp in
the instrumentcluster does not flash. In such
situations, ESP®will not stabilize the vehicle.
It may be best to deactivateESP®in the
followingsituations:
Rwhen using snowchains
Rin deep snow
Ron sand or gravel
If you deactivateESP®:
RESP®no longer improves drivingstability.
Rtraction control is still activated.
RPRE-SAFE®is no longer available, nor is it
activated if you brakefirmly and ESP®
intervenes.
RPRE-SAFE®Brake is no longer available, it
is also not activated if you brakefirmly and
ESP®intervenes.
RESP®still provides support when you
brake.
Rengine torque is no longer limited and the
drive wheels are able to spin.The spinning
wheels produceacuttingeffect for better
traction.
Vehicles with ECO start/stop function: the
ECO start/stop function switches the engine
off automatically when the vehicle comes to
astop. The engine starts automatically when
the driver wants to pull away again. ESP®
remains in its previously selected status. For
example, if ESP®was deactivated before the
engine was switched off, ESP®remains
deactivated when the engine is switched on
again.
EBD (electronic brake force
distribution)
iObserve the "Important safety notes"
section (Ypage 66).
GWARNING
If EBD has malfunctioned, the rear wheels can
still lock, e.g. under full braking. This
increases the risk of skidding and an accident.
You should therefore adapt your driving style
to the different handling characteristics. Have
the brake system checked ataqualified
specialist workshop.
Observe information regarding indicator and
warning lamps (Ypage 267) as well as
displaymessages (Ypage 240).
EBD monitors and controls the brake
pressure on the rear wheels to improve
driving stability while braking.
Driving safety systems71
Safety
Z

In order to maintain the appropriatedistance
to the vehicle in front and thus prevent a
collision, you must apply the brakes yourself.
Due to the nature of the system, particularly
complicated driving conditionsmay cause
unnecessarywarningsortheunnecessary
intervention of PRE-SAFE®Brake.
Followingdamagetothe front end of the
vehicle, have the configurationand operation
of the radarsensorschecked ataqualified
specialist workshop. This also applies to
collisions at low speeds where thereisno
visible damage to the frontofthe vehicle.
Function
XTo activate/deactivate:activate or
deactivate PRE-SAFE®Brake in the on-
board computer (Ypage 228).
If the PRE-SAFE®Brake is not activated, the

symbol appears in the multifunction
display.
If you approachavehicle in front very quickly,
this function warns you fromaspeed of
approximately4mph (7 km/h). An
intermittent warning tone sounds and the
distance warning signal lamp in the
instrumentcluster lightsup.
XBrake immediately to defuse the situation.
or
XTake evasiveaction provided it is safe to do
so.
Fromaspeed of approximately4mph
(7 km/h), if the driver and frontpassenger
have fastened their seat belts, PRE-SAFE®
Brakecan brake the vehicle automatically at
speeds up to approximately 124 mph
(200 km/h).
You can preventthe intervention of the PRE-
SAFE®Brakeatany time by:
Rdepressingthe accelerator pedal further.
Ractivating kickdown.
Rreleasing the brake pedal.
The brakingaction of PRE-SAFE®Brakeis
ended automatically if:
Ryou maneuver to avoid the obstacle.
Rthereisnolonger any danger ofarear-end
collision.
Rthereisnolonger an obstacle detected in
frontofyour vehicle.
If you approach an obstacle and PRE-SAFE®
Brakedetectsarisk ofacollision, the system
will alert you both visually and acoustically. If
you do not brake or takeevasive action,the
system will warn you by automatically braking
the vehicle gently. If thereisanincreased risk
of collision, preventative passenger
protection measures (PRE-SAFE®)are
activated (Ypage 54). Ifarisk of collision
remains at speeds of over 20 mph
(30 km/h) and you do not brake, takeevasive
action or significantly accelerate, automatic
brakingmay be performed up to and including
emergency braking. Automatic emergency
brakingisnot performed until immediately
prior to an accidentthat can no longer be
avoided.
Theftdeterrent locking system
Immobilizer
The immobilizer prevents your vehicle from
being started without the correct SmartKey.
XTo activate with the SmartKey:remove
the SmartKey from the ignition lock.
XTo activate with KEYLESS-GO:switchthe
ignition off and open the driver'sdoor.
XTo deactivate:switchonthe ignition.
When leaving the vehicle, always takethe
SmartKey with you and lock the vehicle.
Anyone can start the engineifavalid
SmartKey has been left inside the vehicle.
iThe immobilizer is always deactivated
when you start the engine.
In the event that the enginecannot be
started when the starter battery is fully
charged, the immobilizer may be faulty.
Theft deterrent locking system73
Safety
Z

SmartKey battery
Important safety notes
GWARNING
Batteries contain toxic and corrosive
substances. If batteries are swallowed, it can
result in severe health problems. There is a
risk of fatal injury.
Keep batteries out of the reach of children. If
abattery is swallowed, seek medical attention
immediately.
Mercedes-Benz recommends that you have
the batteries replaced ataqualified specialist
workshop.
Checking the battery
XPress theorbutton.
The battery is working properly if battery
check lamplights up briefly.
The battery is discharged if battery check
lampdoes not light up briefly.
XChange the battery (Ypage 79).
iIf the SmartKey battery is checked within
the signal reception range of the vehicle,
pressing theorbutton:
Rlocks or
Runlocks the vehicle
iYou can getabattery at any qualified
specialist workshop.
Replacing the battery
You requireaCR20253Vcell battery.
XTake the mechanical key out of the
SmartKey (Ypage 78).
Battery compartmentcover
Mechanical key
XPress mechanical keyinto the opening
in the SmartKey in the direction of the
arrow until battery compartmentcover
opens. Do not hold battery compartment
coverclosed while doing so.
XRemove battery compartmentcover.
$Battery
XRepeatedly tap the SmartKey against your
palm until battery$falls out.
XInsert the new battery with the positive
terminal facing upwards. Usealint-free
cloth to do so.
XMake sure that the surface of the battery is
free of lint, grease and other contaminants.
SmartKey79
Opening and closing
Z